Operating Instructions; Power On / Off; Audible Beep Confirmation; Mute - Jensen VM9411 Instruction Manual

VM9411

OPERATING INSTRUCTIONS

Power On / Off

Press the /MUTE button (1) to turn the unit on. The buttons
on the front of the unit light up and "WELCOME" appears
briefly in the LCD panel (17), followed by the current mode
status. If the TFT screen is open, only the current mode
status is displayed.
Press and hold the /MUTE button (1) on the front panel or
the POWER button (4) on the remote to power off the
unit.The monitor is drawn back into the main compartment
and the LCD screen displays "BYE-BYE".

Audible Beep Confirmation

An audible beep tone confirms each function selection. The
beep tone cannot be disabled.

Mute

Press the /MUTE button (1) on the front panel or the MUTE
button (3) on the remote to mute the volume from the unit.
Press the MUTE button again to restore the volume. "MUTE"
is displayed on the LCD monitor. Adjusting the volume or
using any of the audio set-up features cancels the mute
function.

Playing Source Selection

Press the SRC/P.MODE button (15) on the front panel or the
SRC button (8) on the remote to change between available
playing sources in the following order: Tuner, DVD/CD, XM,
iPod, Aux In, Camera (rear view video camera) and TV. The
playing mode is displayed on the TFT and LCD screens.
AUX IN Mode
An external peripheral device can be connected to this unit
via standard RCA connectors for video and left/right audio.
CAMERA Mode
"CAMERA" mode is only available if the camera is connected
and during reverse driving. To install a rear view video
camera, connect the camera video output cable to the
camera video input cable on the head unit. Refer to the wiring
diagram for proper wiring connections.

Volume Adjustment

To increase or decrease the volume level, turn the ROTARY
ENCODER (6) on the front panel or press the VOL+/ VOL-
buttons (15, 16) on remote control. When the volume level
reaches "0" or "40", a beep sounds, indicating that the
adjustment limit has been reached. The volume ranges from
"0" to "40". The LCD or TFT screen displays the volume level
for 3 seconds.
Programmable Turn-On Volume
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
To program a specific volume level, push and hold the
AUDIO button (2) while the yellow volume bar is displayed on
the screen. The unit will beep two times to confirm your turn-
on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your
audio system to meet the acoustical characteristics of your
vehicle, which vary depending on the type of vehicle and its
measurements. To get the best possible sound quality from
your new system, be sure to adjust the settings for the
speakers as well. Proper setting of the Fader and Balance
boosts the effects of the cabin equalizer.
Accessing the Audio Control Menu
Press the VOL/LOC/DX knob (6) on the front panel once to
display the "AUDIO" menu.
Selecting an Audio Feature for Adjustment
Continuously press the VOL/LOC/DX knob (6) on the front
panel, or press the (>>)/( ) buttons (14, 22) on the remote
<<
control or the (/\)/(V) buttons (18, 19) on the joystick to select
the audio feature to be adjusted.
Adjusting an Audio Feature
Rotate the VOL/LOC/DX knob (6), press the (|<<)/(>>|)
buttons (17, 19) on the remote control, or press the (<)/(>)
buttons (16, 17) on the joystick to adjust the selected feature
to the desired setting.
Table 5: Audio Adjustments
Audio Function Adjustable Range
EQ User
Flat
Jazz
Pop
Classical
Rock
Vocal
Bass -14 to +14
Treble -14 to +14
Fader -7 to +7
Balance -9 to +9
15
Table 5: Audio Adjustments
Audio Function Adjustable Range
Sub -9 to +9
Loud Off, 1-4
NOTE: The Bass and Treble levels are only adjustable
when EQ is set to "User" mode.
Loudness
• The Loudness level/function is dependent on the main
volume setting. As the volume is increased, less
Loudness compensation is applied to the audio signal.
This is referred to "Auto-Loudness". The possible
loudness settings are as follows:
• Off
• 1 - Slight bass boost at low volume level
• 2 - Moderate bass boost at low volume level
• 3 - Good bass boost at low to mid volume level
• 4 - maximum bass boost at mid volume level
Exiting the Audio Control Menu
Press and hold the VOL/LOC/DX knob (6) or stop making
adjustments for a few seconds to exit the audio control menu.

Six-Channel Audio Control

NOTE: Before adjusting the volume of any speaker,
please refer to "Surround Setup" on page 24.
Table 6: 6-Channel Audio Adjustments
Item Adjustable Range
Master Volume 00 to 40
Front Left Channel Volume -10 to +10
Front Right Channel Volume -10 to +10
Rear Left Channel Volume -10 to +10
Rear Right Channel Volume -10 to +10
Center Channel Volume -10 to +10
Subwoofer Volume -10 to +10

Rear Zone

If a monitor is installed in the rear zone and connected to the
rear zone AV output, passengers in the back seat can control