Using Laser Pointer; Setting Projector Ids For Remote Control - Panasonic PT-L6510U Operating Instructions Manual

Using laser pointer

The remote control contains a laser source that can appear as a colored spot on the screen which you can use as
a pointer. The laser beam is activated while the "LASER" button is pressed and held.
Laser Transmitter Window
Operation
indication lamp

Setting projector IDs for remote control

When controlling multiple projectors individually or simultaneously with a single remote control, projector IDs must
be set into the remote control as described in the following steps:
1. Press the "ID SET" button on remote control.
ID number "ALL" will be displayed on the OSD.
2. Press and hold the "ID SET" button for more than 2 seconds.
The ID number will change into "1". The "ID SET" button will now toggle through ID numbers "2", "3", "ALL", "1",
and so on each time it is subsequently pressed.
3. Select the ID number you wish and then press the "ENTER" button.
Note
• The projector ID number in the remote control is set to "ALL" by default. It is therefore not necessary to set a
projector ID number when only one projector is used.
• The projector can be turned ON/OFF from the remote control only if the projector ID is set in the remote
control. For more details on projector ID setting, see page 36.
Warning
DO NOT STARE INTO THE LASER BEAM OR AIM IT AT ANY
PERSON'S EYE. LASER RADIATION CAN CAUSE SERIOUS
INJURY TO THE HUMAN EYE.
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGHT: 640-660nm
MAXIMUM OUTPUT: 1mW
CLASS II LASER PRODUCT
PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J
IN EFFECT AS OF DATE OF MANUFACTURE.
MANUFACTURER: MANUFACTURED:
B
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
IEC60825–1:1993+A1:1997
EN60825–1:1994+A11:1996
WAVE LENGTH :640–660nm
MAX OUTPUT:1mW
RAYONNEMENT LASER
NE PAS REGARDER DANS LE FAISCEAU
APPAREIL A LASER DE CLASSE2
LASER–STRAHLUNG
NICHT IN DEN STRAHL BL ICKEN
LASER KLSSE 2
RADIZIONI LASER
NON GUARDARE NEL RAGGIO LUCE
APPARECCHIO LASER DI CLASSE2
MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.
1-1 Matsushita-cho,Ibaraki,Osaka,567-0026,Japan
MODEL NO.:N2QAEA000003
REMOTE CONTROL
For LCD Projector
MADE IN CHINA
PUSH
Caution
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGHT: 640-660nm
MAXIMUM OUTPUT: 1mW
CLASS II LASER PRODUCT
Laser Specifications:
PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J
IN EFFECT AS OF DATE OF MANUFACTURE.
MANUFACTURER: MANUFACTURED:
B
Wavelength: 640 to 660 nm
LASER RADIATION
Output power: 1 mW (Class II)
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
IEC60825–1:1993+A1:1997
EN60825–1:1994+A11:1996
WAVE LENGTH :640–660nm
MAX OUTPUT:1mW
RAYONNEMENT LASER
NE PAS REGARDER DANS LE FAISCEAU
APPAREIL A LASER DE CLASSE2
LASER–STRAHLUNG
NICHT IN DEN STRAHL BL ICKEN
LASER KLSSE 2
RADIZIONI LASER
NON GUARDARE NEL RAGGIO LUCE
APPARECCHIO LASER DI CLASSE2
MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.
1-1 Matsushita-cho,Ibaraki,Osaka,567-0026,Japan
MODEL NO.:N2QAEA000003
REMOTE CONTROL
For LCD Projector
MADE IN CHINA
• Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
• This remote control unit cannot be repaired.
15