Page 1 TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping, and safe-driving information. Air conditioning and multimedia systems, as well as Interior other interior features for a comfortable driving experi- features ence.
Page 2: Table Of Contents
TABLE OF CONTENTS Index Refer “NAVIGATION SYSTEM OWNER’S MANUAL” information regarding the equipment listed below. • Multimedia system • Rear view monitor system 1-4. Opening and closing the Before driving windows and moon roof Power windows..... 90 Power back window....93 1-1.
Page 3 AVS (Adaptive Variable When driving Suspension System) ..238 Four-wheel drive system ..239 AUTO LSD system ..... 244 2-1. Driving procedures Driving assist systems..246 Driving the vehicle....148 Engine (ignition) switch ..158 2-5. Driving information Automatic transmission..161 Off-road precautions...
Page 4 TABLE OF CONTENTS Index • Personal/interior lights..315 Maintenance and care • Interior light ...... 316 3-4. Using the storage features 4-1. Maintenance and care List of storage features..317 Cleaning and protecting • Glove boxes ..... 318 the vehicle exterior ... 382 •...
Page 5 When trouble arises Vehicle specifications 5-1. Essential information 6-1. Specifications Emergency flashers .... 460 Maintenance data (fuel, oil level, etc.) ... 512 If your vehicle needs to be towed ........ 461 Fuel information....523 If you think something is Tire information ....528 wrong ........
Page 6 Pictorial index Exterior Windshield wipers P. 195  Moon roof P. 96 Hood Outside rear view P. 399 mirrors P. 84 Front side marker lights P. 187 Headlights (low beam) P. 187  Fog lights P. 193 Headlights (high beam) P.
Page 7 Stop/tail and rear side  marker lights P. 187 Roof luggage Tail lights P. 187 carrier P. 88 Rear window defogger P. 307 Fuel filler door P. 100 Back window P. 93 Side doors Rear window P. 35 wiper P. 199 Camera License plate Tires...
Page 8 Pictorial index Interior Seat belts P. 69 Front console box P. 320 Head restraints P. 65 Horn P. 167 Bottle holders P. 337 SRS driver airbag P. 112 Cup holders P. 333 SRS front passenger airbag P. 112 Auxiliary boxes P.
Page 9 Personal/interior lights P. 315  Type A Moon roof switches Personal/interior lights P. 96 P. 315 Overhead console Rear seat entertainment * P. 331 system Conversation mirror SRS curtain shield P. 347 airbags P. 112 Assist grips Personal/interior P. 362 lights P.
Page 10 Pictorial index Interior Type B Personal/interior Personal/interior lights lights P. 315 P. 315 Rear seat entertainment Overhead console * system P. 331 SRS curtain shield Conversation mirror airbags P. 112 P. 347 Personal/interior Assist grips lights P. 315 P. 362 Vanity mirrors P.
Page 11 Door lock switch Driving position memory Inside door lock  switches P. 62 button P. 36 P. 35 Power window Auxiliary box Window lock switches P. 90 P. 338 switch P. 90  : If equipped : Refer to “NAVIGATION SYSTEM OWNER’S MANUAL”.
Page 12 Pictorial index Interior Cup holders P. 333 Ashtray P. 345 Shift lever P. 161 Map holder P. 324 Shift lock override button P. 499...
Page 13 Vehicles without rear seat entertainment system Rear air conditioning system P. 303 Cup holders P. 333 Power outlet P. 348...
Page 14 Pictorial index Interior Vehicles with rear seat entertainment system A/V input port Rear air conditioning system P. 303 Cup holders P. 333 Power outlet P. 348 Headphone jacks...
Page 15 Vehicles with rear console box Rear console box P. 328 Cup holders P. 333 Cup holders P. 333 Seat heater switches Auxiliary box P. 338 P. 355 : Refer to “NAVIGATION SYSTEM OWNER’S MANUAL”.
Page 16 Pictorial index Instrument panel Headlight switch P. 187 Turn signal lever P. 165  Fog light switch P. 193 Gauges and meters P. 168  Multi-information display P. 178 Windshield wipers and washer switch P. 195 Rear window wiper and washer switch P.
Page 17 Rear window defogger switch/  Rear window defogger and outside rear Multimedia system P. 310  view mirror defogger switch P. 307 Rear view monitor system  Windshield wiper de-icer P. 309 Accessory meter Security indicator P. 184 P. 105, 107 Air conditioning system P.
Page 18 Pictorial index Instrument panel Emergency flasher switch P. 460 Accessory meter  control switches P. 184 Multi-information display Intuitive parking assist  control switches P. 178 switch P. 220 Front wheel drive control switch P. 239 Coin holder P. 319 Center differential lock switch P.
Page 19 Power back window switch P. 93 Engine (ignition) switch VSC OFF switch P. 244, 247, 249, 250 P. 158  : If equipped : 4WD models : 2WD models : Vehicles with multi-information display...
Page 20 Pictorial index Instrument panel   Audio remote control switches Telephone switches Talk switch Vehicle-to-vehicle Cruise control  distance button switch P. 202, 206 P. 206...
Page 21 Personal/interior light Tilt and telescopic steering  main switch P. 314 control switch P. 80 Outside rear view Instrument panel light mirror switches control dial P. 84 P. 172  BSM main switch Tilt and telescopic steering P. 227  lock release lever P.
Page 22 Pictorial index Luggage compartment Shopping Seatback folding/ bag hook Power outlet returning switches P. 367 P. 348 P. 60 Power back Back door Child restraint Shopping  door switch strap anchor bracket bag hook P. 41 P. 42 P. 133 P.
Page 23: For Your Information
Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 24 ● Anti-lock brake system ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. Vehicle data recordings Your Toyota is equipped with several sophisticated computers that will record certain data, such as: •...
Page 25 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle) is obtained •...
Page 26 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 27 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 28 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 29: Before Driving
Before driving 1-1. Key information 1-4. Opening and closing the windows and moon roof Keys ........30 Power windows ....90 1-2. Opening, closing and Power back window ... 93 locking the doors Moon roof......96 Wireless remote control ..31 1-5.
Page 30: 1-1. Key Information
Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (P. 500) NOTICE ■...
Page 31: 1-2. Opening, Closing And Locking The Doors
1-2. Opening, closing and locking the doors Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Vehicles with power back door Locks all doors Check that the door is securely locked.
Page 32 1-2. Opening, closing and locking the doors ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Back door: A buzzer sounds and the emergency flashers flash twice to indicate that the back door has been opened/closed.
Page 33 ■ Customization ● That can be configured at Toyota dealer (vehicles without multi-informa- tion display) Settings (e.g. wireless remote control) can be changed. (Customizable features P. 539) ●...
Page 34 1-2. Opening, closing and locking the doors ■ Certification for wireless remote control MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ4-34R IC (Canada) IDs: Transmitter: 1470A-1T Receiver: 1470A-6R MADE IN USA This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Page 35: Side Doors
1-2. Opening, closing and locking the doors Side doors The vehicle can be locked and unlocked using the wireless remote control, key or door lock switch. ■ Wireless remote control P. 31 ■ Locks all doors Closes the windows and moon roof (turn and hold) Unlocks all doors Turning the key unlocks the...
Page 36 1-2. Opening, closing and locking the doors ■ Inside door lock button Locks the door Unlocks the door Pulling the door handle can open the front door even if the inside door lock button is in the lock position. Locking the front doors from the outside without a key Move the inside door lock button to the lock position.
Page 37 1-2. Opening, closing and locking the doors Rear door child-protector lock The door cannot be opened from inside the vehicle when the lock is set. Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
Page 38 1-2. Opening, closing and locking the doors ■ Setting and canceling the functions Vehicles with multi-information display P. 181 Vehicles without multi-information display To switch between setting and canceling, follow the procedure below: Close all the doors and turn the engine switch to the ON posi- tion.
Page 39 1-2. Opening, closing and locking the doors ■ When locking the doors using the key The door cannot be locked if the key is in the engine switch. ■ Key reminder buzzer A buzzer sounds if the driver’s door is opened, while the engine switch is in the ACC or LOCK position to remind you to remove the key.
Page 40: Back Door
1-2. Opening, closing and locking the doors Back door The back door can be locked/unlocked and opened by the following procedures. ■ Locking and unlocking the back door Unlocks all doors Opens the back window (turn and hold) Locks all doors Closes the back window (turn and hold) Door lock switches...
Page 41 1-2. Opening, closing and locking the doors ■ Opening the back door from inside the vehicle (vehicles with power back door) Push and hold the switch to open/close. Power back door switch (vehicles with power back door) Push and hold the switch to close.
Page 42 1-2. Opening, closing and locking the doors Rear step bumper For rear end protection and eas- ier step-up loading. To get on the rear step bumper, use the shaded area in the illus- tration. ■ Back door strap Use the strap when closing. ■...
Page 43 ■ Customization that can be configured at Toyota dealer Settings (e.g. power back door) can be changed. (Customizable features P. 539) CAUTION ■...
Page 44 1-2. Opening, closing and locking the doors CAUTION ■ Operating the back door Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ● Remove any heavy loads, such as snow and ice, from the back door before opening it.
Page 45 When installing an accessory part to the back door, using a genuine Toyota part is recommended. ■ Back door closer (vehicles with a power back door) ●...
Page 46 When installing an accessory part to the back door, using a genuine Toyota part is recom- mended. ■...
Page 47 Do not touch the damper stay rod with gloves or other fabric items. ● Do not attach any accessories other Damper stay rod than genuine Toyota parts to the back door. ● Do not place your hand on the damper stay or apply lateral forces to it.
Page 48: Adjustable Components (Seats, Mirrors, Steering Wheel)
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Manual seat Passenger’s seat Driver’s seat Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever Seat cushion (front) angle adjustment knob Seat lumbar support adjustment switch...
Page 49 1-3. Adjustable components (seats, mirrors, steering wheel) Power seat Passenger’s seat Driver’s seat Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch Vertical height adjustment switch Driver’s seat leg support adjustment switch (if equipped) Seat lumbar support adjustment switch...
Page 50 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of...
Page 51: Rear Seats
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats ■ Second seats Separated seat Seat position adjustment lever Seatback angle adjustment lever...
Page 52 1-3. Adjustable components (seats, mirrors, steering wheel) Bench seat Seat position adjustment lever Seatback angle adjustment lever :The second center seat can be moved forward further than side seats.
Page 53 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Third seats Manual seat Seatback angle adjustment lever...
Page 54 1-3. Adjustable components (seats, mirrors, steering wheel) Power seat Seatback angle adjustment switch Seatback folding/returning switch Moving a second seat for third seat access ■ Getting in the vehicle Pull up the lever and fold down the seatback. The seat will slide forward.
Page 55 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Getting out of the vehicle Depress the release pedal and fold down the seatback. The seat will slide forward. Move the seat to the front-most position Make sure that no passenger is seated on the second seat before depressing the release pedal.
Page 56 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Folding down the second seat Separated seat Pull the lever to unlock the seat- back and then fold the seatback down. Bench seat Pull the lever to unlock the seat- back and then fold the seatback down.
Page 57 1-3. Adjustable components (seats, mirrors, steering wheel) Folding down the third seat ■ Before folding down the third seat To release the hooked end tab, insert the key or concaved end tab into the hole on the buckle. Retract the belt slowly when releasing and stowing the seat belt.
Page 58 1-3. Adjustable components (seats, mirrors, steering wheel) Adjust the center head restraint to the downmost position. Stow the third seat belt buckles.
Page 59 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Folding down the third seat (manual seat) Pull the head restraint lock release lever to fold the head restraint. Pull the lever to unlock the seatback and then fold the seat- back down. From rear door side From back door side...
Page 60 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Folding down the third seat (power seat) From rear door side Press and hold the seatback folding switch until the seatback folds down fully and the buzzer sounds. The outside head restraints are folded automatically.
Page 61 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When adjusting a rear seat ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt.
Page 62: Driving Position Memory (Driver's Seat)
1-3. Adjustable components (seats, mirrors, steering wheel)  Driving position memory (driver’s seat) Your preferred driving position (the position of the driver’s seat, steering wheel and outside rear view mirrors) can be entered into the computer’s memory and recalled with the touch of a button. Two different driving positions can be entered into memory.
Page 63 1-3. Adjustable components (seats, mirrors, steering wheel) Linking driving position memory with door unlock operation Memorized driving positions can be recalled when you unlock the driver’s door using the wireless remote control and open the driver’s door. ■ Setting the linked door unlock operation Set the driving positions into the memory system using the “1”...
Page 64 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Retained accessory power Each memorized position (except for the tilt and telescopic steering column) can be activated within 30 seconds after the driver’s door is opened, even if the key is not in the engine switch. ■...
Page 65: Head Restraints
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Front seats Vertical adjustment Pull the head restraints up. Down Push the head restraint down while pushing the lock release Lock release button button. Second center and outside seats Vertical adjustment...
Page 66 1-3. Adjustable components (seats, mirrors, steering wheel) Third outside seats To use Lift up the head restraint until it locks. To fold Pull the head restraint lock release lever to fold the head restraint. ■ Removing the head restraints Front seats Pull the head restraint up while pushing the lock release button.
Page 67 1-3. Adjustable components (seats, mirrors, steering wheel) Third seats Pull the head restraint up while pushing the lock release button. The head restraint of outside seat can- not be removed. ■ Installing the head restraints Front seats Align the head restraint with the installa- tion holes and push it down to the lock position.
Page 68 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints (front and second outside seats) Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. ■...
Page 69: Seat Belts
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 70 1-3. Adjustable components (seats, mirrors, steering wheel) Releasing the belt Press the release button. ■ Adjusting the height of the belt Down Move the height adjuster up and down as needed until you hear a click.
Page 71 1-3. Adjustable components (seats, mirrors, steering wheel) Third center seat belt The third center seat belt is a 3-point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely latched for proper operation. Make sure that the buckle securely latched for ready use of the center seat belt.
Page 72 1-3. Adjustable components (seats, mirrors, steering wheel) Stow the seat belt tabs in the cover set in the roof as shown. ■ Extracting the belt Pull the belt out partially, and then remove the tabs from the cover. Seat belt comfort guide (third center seat) If the shoulder belt sits close to a person’s neck, use the seat belt comfort guide.
Page 73 1-3. Adjustable components (seats, mirrors, steering wheel) Slide the belt past the slot of the guide. The elastic cord must be behind the seat belt. Seat belt pretensioners (front seats) The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal...
Page 74 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 75 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system.
Page 76 ● If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer. ■ Seat belt damage and wear ●...
Page 77 Seat belt damage and wear ● Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 78 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Using a seat belt extender ● Do not wear the seat belt extender if you can fasten the seat belt without the extender. ● Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
Page 79: Steering Wheel (Manually Adjustable Type)
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel (manually adjustable type) The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and press the lever down. Adjust to the ideal position by moving the steering wheel horizontally and vertically.
Page 80: Steering Wheel (Power-Adjustable Type)
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel (power-adjustable type) The steering wheel can be adjusted to a comfortable position. Down Toward the driver Away from the driver Auto tilt away When the key is removed from the engine switch, the steering wheel returns to its stowed posi- tion by moving up and away to enable easier driver entry and...
Page 81: Anti-Glare Inside Rear View Mirror
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position...
Page 82 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode ON/ The indicator comes on when automatic mode is turned on.
Page 83 1-3. Adjustable components (seats, mirrors, steering wheel) ■ To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them. ■ If a sun visor interferes with the mirror Hold and rotate the mirror to adjust the support.
Page 84: Outside Rear View Mirrors
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch when the engine switch is in the ACC or ON position. Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch.
Page 85 1-3. Adjustable components (seats, mirrors, steering wheel) From inside (if equipped) Press the switch. Pressing again will unfold the mir- rors. Linked mirror function when reversing (if equipped) Press the switch to turn on/off linked mirror function. The outside rear view mirrors will automatically tilt downwards...
Page 86 1-3. Adjustable components (seats, mirrors, steering wheel) ■ When the mirrors are fogged up (vehicles with outside rear view mirror defoggers) Turn on the mirror defoggers to defog the mirrors. (P. 307) ■ Automatic adjustment of the mirror angle (vehicles with driving posi- tion memory) A desired mirror face angle can be entered to memory and recalled automat- ically by the driving position memory.
Page 87 1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE ■ If the mirrors are frozen Do not operate the control or scrape the mirror faces. Use a spray de-icer to free the mirror.
Page 88: Roof Luggage Carrier
1-3. Adjustable components (seats, mirrors, steering wheel) Roof luggage carrier Roof rails Cross rails Adjustment the position of cross rails Turn the knobs counterclockwise to loosen the cross rails. Slide the cross rails to the appro- priate position for loading lug- gage.
Page 89 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Cross rail adjustment Make sure the cross rails are locked securely by applying pressure forward and rearward. Failure to do so may cause an accident, death or serious injury in the event of emergency braking or a collision.
Page 90: 1-4. Opening And Closing The Windows And Moon Roof
1-4. Opening and closing the windows and moon roof Power windows The power windows can be opened and closed using the following switches. Closing One-touch closing (Front windows only) Opening One-touch opening (Front windows only) : To stop the window partway, operate the switch in the oppo- site direction.
Page 91 If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
Page 92 1-4. Opening and closing the windows and moon roof ■ Customization that can be configured at Toyota dealer Settings (e.g. power windows) can be changed. (Customizable features P. 539) CAUTION ■ Closing the windows Observe the following precautions. Failing to do so may result in death or serious injury.
Page 93: Power Back Window
1-4. Opening and closing the windows and moon roof Power back window The power back window can be opened and closed using the switch and key. From inside One-touch closing Closing One-touch opening Opening :Pressing the switch in the opposite direction will stop win- dow travel partway.
Page 94 1-4. Opening and closing the windows and moon roof ■ The power back window can be operated when ● The engine switch is in the ON position. ● The power back window can be opened when the rear window wiper is working.
Page 95 If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer. ■ Customization that can be configured at Toyota dealer Settings (e.g. power back window) can be changed. (Customizable features P. 539) CAUTION ■...
Page 96: Moon Roof
1-4. Opening and closing the windows and moon roof  Moon roof Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing Open The moon roof stops slightly before the fully open position to reduce wind noise.
Page 97 Check to make sure that the moon roof is com- pletely stopped and then release the switch. If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
Page 98 An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off. ■ Customization that can be configured at Toyota dealer Settings (e.g. moon roof) can be changed. (Customizable features P. 539)
Page 99 1-4. Opening and closing the windows and moon roof CAUTION ■ Opening the moon roof Observe the following precautions. Failing to do so may cause death or serious injury. ● Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Page 100: Refueling Opening The Fuel Tank Cap
1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle ● Turn the engine switch to the LOCK position and ensure that all the doors and windows are closed. ●...
Page 101 1-5. Refueling Hang the fuel tank cap on the back of the fuel filler door. Closing the fuel tank cap After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
Page 102 1-5. Refueling ■ Fuel types (P. 515) ■ E85 Fueling Stations (Flex-fuel engine) E85 fueling stations and fuel pumps can be identified by the indication “E85 85% Ethanol”. For more information about fueling stations, please refer to the U.S. Department of Energy Web site. http://www.afdc.energy.gov/afdc/locator/stations/ ■...
Page 103 Do not top off the fuel tank. ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 104 1-5. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface. ■ E85 fuel E85 fuel can be used only in flex-fuel vehicles.
Page 105: 1-6. Theft Deterrent System
1-6. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. This system is designed to help prevent vehicle theft but does not guarantee absolute security against all vehicle thefts.
Page 106 1-6. Theft deterrent system FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For vehicles sold in Canada This device complies with Industry Canada licence-exempt RSS stan- dard(s).
Page 107: Alarm
1-6. Theft deterrent system Alarm The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations when the alarm is set. ● A locked door is unlocked or opened in any way other than using the wireless remote control door lock function or key.
Page 108 1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. ● Nobody is in the vehicle. ●...
Page 109 1-6. Theft deterrent system ■ Alarm-operated door lock In the following cases, depending on the situation, the door may automati- cally lock to prevent improper entry into the vehicle: ● When a person remaining in the vehicle locks the door and the alarm is activated.
Page 110: 1-7. Safety Information
1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (P. 48) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 111 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat while driving. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 112: Srs Airbags
1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. SRS front airbags SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas-...
Page 113 1-7. Safety information Airbag system components Side airbags Curtain shield airbag sen- sors AIR BAG ON and AIR BAG OFF indicator lights SRS warning light Curtain shield airbags Driver’s seat position sen- Front passenger airbag Driver airbag Knee airbags Driver’s seat belt buckle Side and curtain shield air- switch bag sensors...
Page 114 1-7. Safety information Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above.
Page 115 1-7. Safety information ■ Operating conditions (front airbags) ● The SRS front airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approxi- mately 12-18 mph [20-30 km/h] frontal collision with a fixed wall that does not move or deform).
Page 116 1-7. Safety information ■ Conditions under which the SRS airbags may deploy (inflate), other than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration. ●...
Page 117 1-7. Safety information ■ Types of collisions that may not deploy the SRS airbag (side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
Page 118 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or...
Page 119 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
Page 120 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
Page 121 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 122 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad or lower portion of the instrument panel. These items can become projectiles when SRS driver, front passenger and knee airbags deploy.
Page 123 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer.
Page 124: Front Passenger Occupant Classification System
1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.
Page 125 1-7. Safety information Conditions and operation of the front passenger occupant classification system ■ Adult AIR BAG ON and AIR BAG OFF indica- AIR BAG ON tor lights Indicator/ SRS warning light warning light Front passenger’s seat belt reminder Flashing light Front passenger airbag Front passenger knee airbag...
Page 126 1-7. Safety information ■ Unoccupied AIR BAG ON and AIR BAG OFF indica- Not illumi- tor lights nated Indicator/ SRS warning light warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Front passenger knee airbag Side airbag on the front passenger seat Devices Activated Curtain shield airbag in the front passen-...
Page 127 1-7. Safety information : When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/her as an adult depending on his/her physique or posture. : Never install a rear-facing child restraint system on the front pas- senger seat.
Page 128 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 129: Child Restraint Systems
1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Page 130 1-7. Safety information Forward facing — Convertible seat Booster seat ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belts. ●...
Page 131 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 132 1-7. Safety information CAUTION ■ Child restraint precautions ● Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop, sudden swerve or accident.
Page 133: Installing Child Restraints
1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 134 1-7. Safety information ■ Using the seat belts Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (P. 69 ■ Using the top tether strap Anchor brackets (for top tether strap) Second seats (Separated seat) Anchor brackets are provided for all of the second seats.
Page 135 1-7. Safety information Second seats (Bench seat) Anchor brackets are provided for all of the second seats. Third seats Anchor bracket is provided for the third center seat. Installation with LATCH system (second seat only) Second seat (except center seat) Fold the seatback while pulling the lever.
Page 136 1-7. Safety information Second center seat (bench seat) Fold the seatback while pulling the lever. Return the seatback and secure it at the 1st lock posi- tion (most upright position). Adjust the seatback to the 8th lock position. (P. 51) 1st lock position 8th lock position Type A...
Page 137 1-7. Safety information Type B Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. The anchors are installed in the lower seatback under a flap. Confirm the position of the anchors below the sym- bol in the seatback.
Page 138 1-7. Safety information Installing child restraints using a seat belt (child restraint lock function belt) Rear facing Infant seat/convertible seat ■ Place the child seat on the rear seat facing the rear of the vehi- cle. Run the seat belt through the child seat and insert the plate into the buckle.
Page 139 1-7. Safety information While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 140 1-7. Safety information While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 141 1-7. Safety information Removing a child restraint installed with a seat belt Push the buckle release button and fully retract the seat belt. Child restraint systems with a top tether strap Second seat Secure the child restraint using the LATCH anchors or seat belt, and adjust the head restraint to the upmost position.
Page 142 1-7. Safety information Second seat Latch the hook onto the anchor bracket and tighten the top tether strap. Make sure the top tether strap is securely latched. Hook Top tether strap Anchor bracket Third center seat Open the anchor bracket cover. Latch the hook onto the anchor bracket and tighten the top tether strap.
Page 143 1-7. Safety information ■ Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819. CAUTION ■...
Page 144 1-7. Safety information CAUTION ■ When installing a child restraint system ● Only put a forward-facing or booster child seat on the front seat when unavoidable. When installing a forward- facing or booster child seat on the front passenger seat, move the seat as far back as possible even if the AIR BAG OFF indicator light is illuminated.
Page 145 1-7. Safety information CAUTION ■ When installing a child restraint system (vehicles with bench type sec- ond seat) Observe the following precautions. Failure to do so may cause death or serious injury to the child or other pas- sengers in the event of a sudden stop or accident. ●...
Page 146 1-7. Safety information...
Page 147: When Driving
When driving 2-1. Driving procedures 2-4. Using other driving systems Driving the vehicle.... 148 Cruise control....202 Dynamic laser cruise Engine (ignition) switch ..158 control ......206 Automatic transmission..161 Intuitive parking assist..220 Turn signal lever ....165 Parking brake....
Page 148: 2-1. Driving Procedures
2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine (P. 158) ■ Driving With the brake pedal depressed, shift the shift lever to D. (P. 161) Release the parking brake. (P.
Page 149 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down operation.
Page 150 2-1. Driving procedures ■ Operating your vehicle in a foreign country Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (P. 515) ■ When turning off the engine The emission system operating sounds may continue for a short time after the engine is turned off.
Page 151 Have the vehicle inspected by your Toyota dealer immediately. ● Do not shift the shift lever to P while the vehicle is moving.
Page 152 2-1. Driving procedures CAUTION ■ When driving the vehicle ● Do not adjust the position of the steering wheel, the seat, or the inside or outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.
Page 153 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● Do not race the engine. If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, and may cause an accident. ●...
Page 154 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in...
Page 155 2-1. Driving procedures CAUTION ■ When taking a nap in the vehicle Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.
Page 156 If you hear a squealing or scraping noise while driving (brake pad wear limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed.
Page 157 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ● Brake function ●...
Page 158: Engine (Ignition) Switch
2-1. Driving procedures Engine (ignition) switch ■ Engine switch LOCK The steering wheel is locked and the key can be removed. (The key can be removed only when the shift lever is in P.) Some electrical components such as the audio system can be used.
Page 159 2-1. Driving procedures ■ Turning the key from ACC to LOCK Shift the shift lever to P. (P. 161) Push in the key and turn to the LOCK position. ■ Steering lock release When starting the engine, the engine switch may seem stuck in the LOCK posi- tion.
Page 160 2-1. Driving procedures NOTICE ■ To prevent battery discharge Do not leave the engine switch in the ACC or ON position for long periods if the engine is not running. ■ When starting the engine ● Do not crank for more than 30 seconds at a time. This may overheat the starter and wiring systems.
Page 161: Automatic Transmission
2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever While the engine switch is on, depress the brake pedal and move the shift lever. ■ Shift position uses Shift position Function Parking the vehicle or starting the engine Reversing...
Page 162 2-1. Driving procedures Changing shift ranges in S mode Shift the shift lever to the S position and operate the shift lever. Upshifting Downshifting The initial shift range in S mode is automatically set to 5 or 4 accord- ing to vehicle speed. However, the initial shift range may be set to 3 or 2 if the AI-SHIFT has operated while the shift lever was in the D ...
Page 163 If the S indicator does not come on even after shifting the shift lever to This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer, immediately. (In this situation, the vehicle will operate as if the shift lever is in D.) ■...
Page 164 2-1. Driving procedures ■ Downshifting restrictions warning buzzer (in the S mode) To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (The warning buzzer will sound twice.) ■...
Page 165: Turn Signal Lever
2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 166: Parking Brake
2-1. Driving procedures Parking brake parking brake*. (Depressing the pedal again releases the parking brake.) U.S.A. Canada At this time, the indicator will come on. *: Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot.
Page 167: Horn
2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel (vehicles with manual tilt and tele- scopic steering) Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (P.
Page 168: Instrument Cluster Gauges And Meters
2-2. Instrument cluster Gauges and meters Vehicles with multi-information display The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank.
Page 169 2-2. Instrument cluster Multi-information display P. 178 Automatic transmission fluid temperature gauge Displays the automatic transmission fluid temperature.
Page 170 2-2. Instrument cluster Vehicles without multi-information display The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Voltmeter Displays the charge state.
Page 171 2-2. Instrument cluster Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.
Page 172 While driving ● When the voltmeter indicates more than 19 V or less than 9 V, the battery may be malfunctioning. Have your vehicle checked at your Toyota dealer. ● When the engine oil pressure gauge does not work properly, immediately stop the engine and contact your Toyota dealer.
Page 173: Indicators And Warning Lights
2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster (vehicles with multi-information display) Instrument cluster (vehicles without multi-information display)
Page 174 2-2. Instrument cluster Center panel Outside rear view mirrors [vehicles with BSM (Blind Spot Moni- tor)]...
Page 175 2-2. Instrument cluster ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Tail light indicator (P. 165) (P. 187) (Canada) Headlight high beam AUTO LSD indicator indicator (P. 191) (P. 244, 247) Security indicator Center differential lock (P.
Page 176 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
Page 177 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 178: Multi-Information Display
2-2. Instrument cluster  Multi-information display The multi-information display presents the driver with a variety of driving-related data. ● Trip information (P. 178) Displays driving range, fuel consumption and other cruis- ing-related information. ● Warning messages (P. 480) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.
Page 179 2-2. Instrument cluster Zoom display of odometer and trip meters Displays the odometer and one of the trip meters simultaneously. Average Fuel Economy Displays the average fuel consumption since the function was reset. ● The function can be reset by pushing the SELECT RESET button for more than 2 seconds when the Average Fuel Economy is displayed.
Page 180 2-2. Instrument cluster Trip Timer Displays the driving time. To calculate the driving time, press the SELECT RESET button, and to stop the calculation, press it again. To reset the calculation, press the SELECT RESET button for more than 2 seconds. Average Speed Displays the average vehicle speed since the engine was started or the function was reset.
Page 181 2-2. Instrument cluster Feature customization The vehicle can be customized while the vehicle is stopped. Press the SETUP button to select the item you want to cus- tomize unit. UNITS KEYLESS ENTRY FEEDBACK KEYLESS ENTRY RELOCK TIMER KEYLESS ENTRY ALL DOORS UNLOCK DOOR AUTO LOCKING DOOR AUTO UNLOCKING HEADLAMPS AUTO OFF TIMER...
Page 182 2-2. Instrument cluster Items Screen text Select in this order Double switch KEYLESS ENTRY operation to 1 PRESS 2 PRESSES ALL DOORS unlock all the UNLOCK doors ABOVE 12 MPH SHIFT OUT Automatic door DOOR AUTO OF PARK (20 km/h) LOCKING locking function DRIVER DOOR...
Page 183 ■ Feature customization error • If SYSTEM ERROR message is indicated, turn the engine switch off and then on again. • If SYSTEM ERROR message is indicated again, contact your Toyota dealer. CAUTION ■ Caution while driving Do not adjust the display.
Page 184: Accessory Meter
2-2. Instrument cluster Accessory meter Outside temperature display Displays the outside air temperature. (P. 343) Outside temperature and trip information display (if equipped) Displays the outside temperature and trip information. (P. 171343) Clock (P. 342) H (Hour) button P. 342 (...
Page 185 2-2. Instrument cluster Outside temperature and trip information display (if equipped) Every time the INFO button is pushed, the display toggles through these information. ● OUTSIDE (outside temperature display) Displays the outside air temperature. ● AVG (average fuel consumption after refueling) Displays the average fuel consumption since the vehi- cle was last refueled.
Page 186 2-2. Instrument cluster ● Display off ■ The accessory meter can be operated when The engine switch must be in the ON position. ■ To select the unit A (English/U.S. customary system) or unit B (metric unit) (vehicles without multi-information display) Press the SETUP button to change the units.
Page 187: Operating The Lights And
2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Type A Vehicles with day- time running light system: The daytime running lights turn on. (P. 191) side marker, U.S.A. Canada parking, tail, license plate, daytime run- ning lights...
Page 188 2-3. Operating the lights and wipers Type B Vehicles with day- time running light system: The daytime running lights turn on. (P. 191) side marker, U.S.A. Canada parking, tail, license plate, daytime run- ning lights equipped) (P. 191) and instrument panel lights turn on.
Page 189 2-3. Operating the lights and wipers Type C The daytime running lights turn off. The headlights, side marker, parking, tail, license plate, day- time running lights (P. 191) and instru- ments panel lights turn on and off auto- matically. (When the engine switch is in the ON position) side...
Page 190 2-3. Operating the lights and wipers Type D The daytime running lights turn off. The headlights, side marker, parking, tail, license plate, day- time running lights (P. 191) and instru- ments panel lights turn on and off auto- matically. (When the engine switch is in the ON position) side...
Page 191 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams.
Page 192 ■ Customization ● That can be configured at Toyota dealer. (vehicles without multi-informa- tion display) Settings (automatic light off system) can be changed. (Customizable features P. 539) ● It is possible to change the settings. (vehicles with multi-information dis- play) (Feature customization P.
Page 193: Fog Light Switch
2-3. Operating the lights and wipers  Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. Type A Front fog lights ON ...
Page 194 2-3. Operating the lights and wipers Type B Front fog lights ON...
Page 195: Windshield Wipers And Washer
2-3. Operating the lights and wipers Windshield wipers and washer Wiper intervals can be adjusted for intermittent operation (when is selected.) Type A Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation Increases the intermittent...
Page 196 2-3. Operating the lights and wipers Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. Type B Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 197 2-3. Operating the lights and wipers Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. ■ The windshield wiper and washer can be operated when The engine switch must be in the ON position.
Page 198 Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. ■ When a nozzle becomes blocked In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
Page 199: Rear Window Wiper And Washer
2-3. Operating the lights and wipers Rear window wiper and washer Type A Intermittent window wiper operation Normal window wiper operation Washer/wiper dual operation Washer/wiper dual operation The rear window wiper oper- ates while the washer squirts.
Page 200 ● The engine switch must be in the ON position. ● The back window is fully closed. ■ Customization that can be configured at Toyota dealer Settings (e.g. washer linkage wiper control) can be changed. (Customizable featuresP. 539) NOTICE ■...
Page 201: Headlight Cleaner Switch
2-3. Operating the lights and wipers  Headlight cleaner switch Washer fluid can be sprayed on the headlights. Press the switch to clean the headlights. ■ The headlight cleaner can be operated when The engine switch is in the ON position and the headlights are turned on. NOTICE ■...
Page 202: 2-4. Using Other Driving Systems
2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicator Cruise control switch ■ Setting the vehicle speed Press the ON-OFF button to activate the cruise control. Cruise control indicator will come on.
Page 203 2-4. Using other driving systems ■ Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
Page 204 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
Page 205 2-4. Using other driving systems CAUTION ■ To avoid operating the cruise control by mistake Switch the cruise control off using the ON-OFF button when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
Page 206: Dynamic Laser Cruise Control
2-4. Using other driving systems  Dynamic laser cruise control Dynamic laser cruise control supplements conventional cruise con- trol with a vehicle-to-vehicle distance control. In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates or decelerates in order to maintain a set following distance from vehi- cles ahead.
Page 207 2-4. Using other driving systems ■ Setting the vehicle speed (vehicle-to-vehicle distance con- trol mode) Press the ON-OFF button to activate the cruise control. Cruise control indicator will come on. Press the button again to deactivate the cruise control. Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
Page 208 2-4. Using other driving systems ■ Adjusting the set speed To change the set speed, operate the lever until the desired set speed is displayed. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
Page 209 2-4. Using other driving systems ■ Changing the vehicle-to-vehicle distance Pressing the button changes Preceding vehicle mark vehicle-to-vehicle dis- tance as follows: Long Medium Short The vehicle-to-vehicle distance is set automatically to long mode when the engine switch is turned to the ON position. If a vehicle is running ahead of you, the preceding vehicle mark will also be displayed.
Page 210 2-4. Using other driving systems ■ Canceling and resuming the speed control Pulling the lever toward you cancels the cruise control. The speed setting is also can- celed when the brakes are applied. Pushing lever resumes the cruise control and returns vehicle speed to the set speed.
Page 211 2-4. Using other driving systems Driving in vehicle-to-vehicle distance control mode This mode employs a laser radar sensor to detect the presence of vehicles up to approximately 400 ft. (120 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to main- tain a suitable following distance from the vehicle ahead.
Page 212 2-4. Using other driving systems Example of follow-up cruising When following a vehicle driving slower than the set speed The system continues follow-up cruising while adjusting for changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle dis- tance set by the driver.
Page 213 2-4. Using other driving systems Selecting conventional constant speed control mode Constant speed control mode differs from vehicle-to-vehicle distance control mode. When constant speed control mode is selected, your vehicle will maintain a set speed regardless of whether or not there are other vehicles in the lane ahead.
Page 214 (4WD models) :Vehicle-to-vehicle distance control driving must be reset by pressing the ON-OFF button again. If vehicle-to-vehicle distance control driving is automatically canceled for any other reason, there may be a malfunction in the system. Contact your Toyota dealer.
Page 215 2-4. Using other driving systems ■ Automatic cancelation of constant speed control The cruise control will stop maintaining the vehicle speed in the following sit- uations: ● Actual vehicle speed is more than approximately 10 mph (16 km/h) below the set vehicle speed At this time, the memorized set speed is not retained.
Page 216 2-4. Using other driving systems CAUTION ■ Before using dynamic laser cruise control Do not overly rely on vehicle-to-vehicle distance control. Be aware of the set speed. If automatic deceleration/acceleration is not appropriate, adjust the vehicle speed, as well as the distance between your vehicle and vehicles ahead by applying the brakes etc.
Page 217 2-4. Using other driving systems CAUTION ■ Situations unsuitable for dynamic laser cruise control Do not use dynamic laser cruise control in any of the following situations. Doing so may result in inappropriate speed control and could cause an acci- dent resulting in death or serious injury.
Page 218 2-4. Using other driving systems CAUTION ■ When the sensor may not be correctly detecting the vehicle ahead Apply the brakes as necessary when any of the following types of vehicles are in front of you. As the sensor may not be able to correctly detect these types of vehicles, the approach warning (P.
Page 219 ● Do not disassemble the sensor. ● Do not attach accessories or stickers to the sensor, surrounding area. ● Do not modify or paint the sensor. ● If the laser radar sensor needs to be replaced, contact your Toyota dealer.
Page 220: Intuitive Parking Assist
2-4. Using other driving systems  Intuitive parking assist The intuitive parking assist is designed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer when parking the vehicle. This system uses sensors to detect obstructions.
Page 221 2-4. Using other driving systems ■ Intuitive parking assist switch Press the switch to turn on. (To turn off, press the switch again.) When on, the indicator light comes on to inform the driver that the system is operational. The distance and buzzer ■...
Page 222 2-4. Using other driving systems Rear corner sensors Distance shown Indicator Zone in in. and buzzer (mm) Approximately 33.5 — 20.5 Intermittent (850 — 520) Approximately Fast 20.5 — 15.7 intermittent (520 — 400) Approximately Near 15.7 (400) or Continuous less Front corner sensors Distance shown...
Page 223 2-4. Using other driving systems ■ When two or more obstacles are detected simultaneously The buzzer system responds to the nearest zone. ■ When multiple obstacles are detected in front and behind the vehicle at the same time The buzzer will change in the following manner. ●...
Page 224 2-4. Using other driving systems Sensors that operate and detection range The following diagrams show the sensor detection range. Note that sensors may not be able to detect obstacles that are extremely close to the vehicle. ■ Detection range of the sensors Back sensors Rear corner sensors Front corner sensors...
Page 225 Objects lower than the sensors or thin stakes etc. may be detected ini- tially, but as they draw closer, they may cease to be detected. • A towing hitch is mounted to the vehicle. • A non-genuine Toyota suspension (lowered suspension etc.) is installed. • When attaching a two-way radio antenna.
Page 226 This ISM device complies with Canadian ICES-001. ■ If the indicator is continuously on Have the vehicle inspected by your Toyota dealer. ■ If the indicator remains blinking but do not sound the buzzer Clean the sensors with soft cloth.
Page 227: Bsm (Blind Spot Monitor)
2-4. Using other driving systems  BSM (Blind Spot Monitor) The Blind Spot Monitor is a system that assists the driver to confirm safety when changing lanes. The system uses radar sensors to detect vehicles that are traveling in an adjacent lane in the area that is not reflected in the outside rear view mirror (the blind spot), and advises the driver of the vehi- cles existence via the outside rear view mirror indicator.
Page 228 2-4. Using other driving systems The Blind Spot Monitor system detection areas The blind spot that vehicles can be detected in are outlined below. The range of the detection area extends to: Approximately 11.5 ft. (3.5 m) from the side of the vehicle The first 1.6 ft.
Page 229 2-4. Using other driving systems ■ Conditions under which the Blind Spot Monitor will not detect a vehicle The Blind Spot Monitor is not designed to detect the following types of vehi- cles and/or objects: ● Vehicles traveling in the opposite direction ●...
Page 230 2-4. Using other driving systems ● Instances of the Blind Spot Monitor unnecessarily detecting a vehicle and/or object may increase under the following conditions: • When there is only a short distance between your vehicle and a guard- rail, wall etc. •...
Page 231 2-4. Using other driving systems For vehicles sold in Canada IC: 4135A-BSDTX This device complies with the radio standards specification RSS-220 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 232 If the sensor moves even slightly off position, the system may mal- function and vehicles that enter the detection area may not be detected. If the sensor or surrounding area is subject to a strong impact, always have the area inspected by your Toyota dealer. ● Do not disassemble the sensor.
Page 233: Electronically Modulated Air Suspension
2-4. Using other driving systems  Electronically modulated air suspension The electronically modulated air suspension allows the driver to control the vehicle’s height in order to adjust for driving conditions. Select the desired height with the height control switch. Height control switch Height control mode select switch Selecting vehicle height...
Page 234 2-4. Using other driving systems ■ Height modes ● N mode (normal mode): For ordinary driving Normal height ● HI mode (high mode): For driving on bumpy roads 1.2 in. (30 mm) higher than the normal height The HI mode is unavailable when the vehicle’s speed exceeds 18 mph (30 km/h).
Page 235 2-4. Using other driving systems ■ Automatic leveling function Regardless of the number of occupants or the luggage load, vehicle height in any mode is always adjusted to a fixed height by the automatic leveling function. ■ When HI mode is selected The vehicle height will change to N mode when driving at the speeds of 18 mph (30 km/h).
Page 236 2-4. Using other driving systems CAUTION ■ The electronically modulated air suspension must be turned off in the following circumstances: Otherwise, the automatic leveling function may cause the vehicle’s height to change, and you may catch part of your body in the vehicle, resulting in an unexpected accident: ●...
Page 237 2-4. Using other driving systems NOTICE ■ Be careful in any place where overhead space is limited. When changing to a higher mode or after unloading, the vehicle height will rise. This may cause damage to the vehicle. ■ Do not select LO mode when driving on bumpy roads. If the underbody of the vehicle touches a rugged road surface, the vehicle may be damaged.
Page 238: Avs (Adaptive Variable Suspension System)
2-4. Using other driving systems  AVS (Adaptive Variable Suspension System) AVS controls the suspension according to the road and driving con- ditions. Selecting an optimum driving mode allows good vehicle posture and steering wheel operation. Sport mode For winding mountain road driving or high speed driving.
Page 239: Four-Wheel Drive System
2-4. Using other driving systems  Four-wheel drive system Use the front wheel drive control switch to select the following trans- fer modes. : Vehicles with multi-information display : Vehicles without multi-information display 2WD (high speed position, two-wheel drive) Normal driving. 4H (high speed position, four-wheel drive) Greater traction than two wheel drive.
Page 240 2-4. Using other driving systems Shifting between 4H and 4L ■ Shifting from 4H to 4L Stop the vehicle completely. Shift the shift lever to N. Push and turn the front wheel drive control switch fully clock- wise. Maintain this condition until the 4LO indicator turns on. ■...
Page 241 2-4. Using other driving systems ■ Shifting between 2WD and 4H ● Reduce your speed to less than 62 mph (100 km/h) and set the front wheel drive control switch between 2WD and 4H. When the ambient temperature is 5.0°F (-15°C) or lower, shifting from 2WD to 4H cannot be performed with the vehicle speed above 43 mph (70 km/h).
Page 242 In this case, you may not be able to shift between 2WD and 4H, 4H and 4L, and the cen- ter differential lock may not be operable. Have the vehicle inspected by your Toyota dealer immediately. ■ Shifting to 4L position The VSC OFF indicator will come on.
Page 243 2-4. Using other driving systems CAUTION ■ Shifting from 2WD to 4H while driving Never operate the front wheel drive control switch if the wheels are slipping. Stop the slipping or spinning before shifting. ■ When the vehicle is parked If the shift lever is moved before the 4LO indicator turns on/off, the transfer mode may not be shifted completely.
Page 244: Auto Lsd System
2-4. Using other driving systems AUTO LSD system The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when one of the rear wheels spin- ning occurs in a ditch or rough surface.
Page 245 2-4. Using other driving systems When the AUTO LSD system is operating If the rear wheels spin, the slip indicator flashes to indicate that the AUTO LSD system has con- trolled the spinning of the rear wheels. ■ If the engine is turned off and restarted The AUTO LSD system and the indicators are automatically turned off.
Page 246: Driving Assist Systems
2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
Page 247 2-4. Using other driving systems When VSC/Trailer Sway Control/TRAC/A-TRAC are operating The slip indicator will flash while VSC/Trailer Sway Con- trol/TRAC/ A-TRAC systems are operating. To disable VSC, Trailer Sway Control and/or TRAC (2WD models and 2WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and/or TRAC may reduce power from the engine to the wheels.
Page 248 2-4. Using other driving systems ■ AUTO LSD mode Stop the vehicle completely, and press the VSC OFF switch for more than 3 seconds, when the system is in the TRAC OFF mode. The VSC OFF and AUTO LSD indicators will come on. The system is in TRAC off, AUTO LSD on and VSC, Trailer Sway Control off mode.
Page 249 2-4. Using other driving systems To disable VSC, Trailer Sway Control and/or A-TRAC (4H mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and/or A-TRAC may reduce power from the engine to the wheels.
Page 250 ■ When the TRAC OFF indicator comes on even if the VSC OFF switch has not been pressed TRAC cannot be operated. Contact your Toyota dealer. ■ Sounds and vibrations caused by the ABS, TRAC, A-TRAC, VSC, Trailer Sway Control and brake assist system ●...
Page 251 2-4. Using other driving systems ■ If the brake system overheats TRAC or A-TRAC will cease operation, and the slip indicator will change from flashing to being on continuously to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.) ■...
Page 252 The ABS, VSC and Trailer Sway Control will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.
Page 253 2-4. Using other driving systems CAUTION ■ If trailer sway occurs Observe the following precautions. Failing to do so may cause death or serious injury. ● Firmly grip the steering wheel. Steer straight ahead. Do not try to control trailer swaying by turning the steering wheel. ●...
Page 254: 2-5. Driving Information
2-5. Driving information Off-road precautions This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off-road applications.
Page 255 2-5. Driving information CAUTION ■ Off-road vehicle precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 256 2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
Page 257 2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places.
Page 258 2-5. Driving information NOTICE ■ To prevent the water damage ● Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ●...
Page 259: Cargo And Luggage
2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment whenever possible. ● Be sure all items are secured in place. ●...
Page 260 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle...
Page 261 2-5. Driving information As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.
Page 262 Roof luggage carrier precautions To use the roof rails as a roof luggage carrier, you must fit the roof rails with two or more genuine Toyota cross rails or their equivalent. When you load cargo on the roof luggage carrier, observe the following: ●...
Page 263 2-5. Driving information CAUTION ■ Roof luggage carrier precautions ● If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then during the trip to make sure the cargo remains in its place. ●...
Page 264: Vehicle Load Limits
2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. ■ Total load capacity (vehicle capacity weight): (P. 513) Total load capacity means the combined weight of occupants, cargo and luggage.
Page 265 2-5. Driving information CAUTION ■ Overloading the vehicle Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
Page 266: Winter Driving Tips
2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 267 2-5. Driving information ■ When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. ■ When parking the vehicle Park the vehicle and move the shift lever to P without setting the parking brake.
Page 268 2-5. Driving information Regulations on the use of snow chains ● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains. ● Install the chains on the rear tires. ●...
Page 269 NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota deal- ers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the operation of the tire pressure warning valves and transmitters.
Page 270: Trailer Towing
To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional...
Page 271 2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
Page 272 2-5. Driving information ■ GAWR (Gross Axle Weight Rating) The maximum allowable gross Front GAWR axle weight. The gross axle weight is the load placed on each axle (front and rear). Rear GAWR ■ TWR (Trailer Weight Rating) The maximum allowable gross (With brakes) trailer weight.
Page 273 2-5. Driving information ■ Unbraked TWR (Unbraked Trailer Weight Rating) The trailer weight rating for tow- (Without brakes) ing a trailer without a trailer ser- vice brake system. ■ Tongue Weight The load placed on the trailer hitch ball. (P. 276)
Page 274 2-5. Driving information Weight limits ● The gross trailer weight must never exceed the TWR described in the table. (P. 275) ● The gross combination weight must never exceed the GCWR described in the table. (P. 275) ● The gross vehicle weight must never exceed the GVWR indi- cated Certification...
Page 275 2-5. Driving information GCWR, TWR and Unbraked TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR and TWR Driving Model code Engine GCWR system 7400 lb.
Page 276 2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. •...
Page 277 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
Page 278 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
Page 279 2-5. Driving information Positions for towing hitch receiver Hitch receiver pin hole posi- tion: 46.2 in. (1172.3 mm) Connecting trailer lights Use the wire harness stored in the rear end under the vehicle body. 4 pin connector 4 pin, 7 pin connectors...
Page 280 2-5. Driving information ■ Service connector for towing brake controller (with towing package) Your vehicle is equipped with a service connector for the trailer brake controller as shown. Access the service connector. Remove the scuff plate. Remove the clip (screw type) and trim board.
Page 281 2-5. Driving information ● Disconnecting Set the height control of electronically modulated air suspen- sion system to N mode. Set the electronically modulated air suspension system to MAN. (manual). Turn off the engine. Set the supporting leg of the trailer on the ground and raise the hitch by 4 in.
Page 282 ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
Page 283 2-5. Driving information ● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak- ing a turn. ● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.
Page 284 2-5. Driving information ● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoid- able, do so only after performing the following: Apply the brakes and keep them applied.
Page 285 2-5. Driving information ■ Matching trailer ball height to trailer coupler height No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer. Coupler Trailer ball ■...
Page 286 Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
Page 287 2-5. Driving information If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases. CAUTION ■...
Page 288 ■ When towing a trailer Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. ● If the gross trailer weight exceeds unbraked TWR, trailer brakes are required.
Page 289 NOTICE ■ When installing a trailer hitch Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ■ Do not directly splice trailer lights Do not directly splice trailer lights.
Page 290: Dinghy Towing
2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
Page 291 2-5. Driving information...
Page 292: Interior Features
Interior features 3-1. Using the air conditioning system and defogger Front air conditioning system ......294 Rear air conditioning system ......303 Rear window and outside rear view mirror defoggers .... 307 Windshield wiper de-icer ......309 3-2. Using the multimedia system Multimedia system types ......
Page 293 Interior features 3-4. Using the storage features 3-5. Using the other interior features List of storage features ..317 Sun visors ......340 • Glove boxes....318 Vanity mirrors....341 • Coin holder ....319 Clock ........ 342 • Front console box ..320 Outside temperature •...
Page 294: Front Air Conditioning System
3-1. Using the air conditioning system and defogger Front air conditioning system Airflow and outlets are automatically adjusted according to the tem- perature setting. Control panel Air outlet Windshield defogger selection dial Driver’s side temperature control dial Front passenger’s side temperature Air conditioning ON/OFF switch control dial Automatic mode...
Page 295 3-1. Using the air conditioning system and defogger Display Front passenger’s side Fan speed display Airflow display temperature setting display Temperature setting Driver’s side temperature display for rear passengers setting display Using the automatic mode Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting.
Page 296 3-1. Using the air conditioning system and defogger Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter- clockwise (cool). The air conditioning system switches between individual and simultaneous modes each time is pressed. ●...
Page 297 3-1. Using the air conditioning system and defogger ■ Changing the air outlets Turn the air outlet selection dial. The air outlets switch each time either side of air outlet selection dial is turned. Air flow as shown according to the mode selected. When the dial is set to , air flows to the upper body.
Page 298 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the feet. When the dial is set to , air flows to the feet and the wind- shield defogger operates. Recirculated air mode will auto- matically switch to outside air mode.
Page 299 3-1. Using the air conditioning system and defogger Defogging the windshield Press The indicator comes on. The air conditioning system con- trol operates automatically. Recirculated air mode will auto- matically switch to outside air mode. Adjusting the position and opening and closing the air outlets Driver side outlets Direct air flow to the left or right, up or down.
Page 300 3-1. Using the air conditioning system and defogger Passenger side outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent. ■ Using the automatic mode Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions.
Page 301 There may be a problem in the air conditioning system if the indi- cator continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer. ■ Ventilation and air conditioning odors ●...
Page 302 3-1. Using the air conditioning system and defogger CAUTION ■ To prevent the windshield from fogging up Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.
Page 303: Rear Air Conditioning System
3-1. Using the air conditioning system and defogger Rear air conditioning system Airflow and outlets are automatically adjusted according to the tem- perature setting. Temperature setting Automatic mode Airflow control display Temperature control Fan speed control for rear passengers ■ Button lock function During Simultaneous mode (the indicator on is on), the rear air condi-...
Page 304 3-1. Using the air conditioning system and defogger Using the automatic mode Press The indicator comes on. The air conditioning system will operate, and air outlets and fan speed will be set automatically. Press to increase the temperature and decrease it. Adjusting the settings ■...
Page 305 3-1. Using the air conditioning system and defogger is pressed, air When flows to the upper body and feet. The indicator comes on. is pressed, air When flows to the feet. The indicator comes on. ■ Adjusting the fan speed (decrease ...
Page 306 3-1. Using the air conditioning system and defogger Adjusting the position and opening and closing the air outlets Roof side outlets Direct air flow to the left or right, up or down. NOTICE ■ To prevent battery discharge Do not leave the air conditioning system on longer than necessary when the engine is stopped.
Page 307: Rear Window And Outside Rear View Mirror Defoggers
3-1. Using the air conditioning system and defogger  Rear window and outside rear view mirror defoggers These features are used to defog the rear window, and to remove raindrops, dew and frost from the outside rear view mirrors. On/off Press the button to turn on the rear window defogger.
Page 308 3-1. Using the air conditioning system and defogger CAUTION ■ When the outside rear view mirror defoggers are on (vehicles with out- side rear view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
Page 309: Windshield Wiper De-Icer
3-1. Using the air conditioning system and defogger  Windshield wiper de-icer This feature is used to prevent ice from building up on the wind- shield and wiper blades. On/off Press the button to turn on the windshield wiper de-icer. The indicator light will come on.
Page 310: 3-2. Using The Multimedia System
3-2. Using the multimedia system  Multimedia system types Entune Audio Plus Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”. Entune Premium Audio Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.  : If equipped...
Page 311: Usb Port/Aux Port
3-2. Using the multimedia system USB port/AUX port Connect an iPod, USB memory device or portable audio player to the USB port/AUX port as indicated below. Select “iPod”, “USB” or “AUX” on the “Select Audio Source” screen and the device can be operated via multimedia system.
Page 312: Using The Aux Port
3-2. Using the multimedia system Using the AUX port To use the AUX port, connect a portable player, then select “AUX” on the “Select Audio Source” screen. Connecting a portable audio player P. 311 ■ Operating portable audio players connected to the multimedia system The volume can be adjusted using the vehicle’s audio controls.
Page 313: 3-3. Using The Interior Lights
3-3. Using the interior lights Interior lights list Your Toyota is equipped with an illuminated entry system to assist in entering the vehicle. Due to the function of the system, the lights shown in the following illustration automatically turn on/off accord- ing to whether the doors are locked/unlocked, whether the doors are opened/closed, and the engine switch position.
Page 314: Personal/Interior Light Main Switch
20 minutes. ■ Customization ● That can be configured at Toyota dealer (vehicles without multi-informa- tion display) Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features P. 539) ●...
Page 315: Personal/Interior Lights
3-3. Using the interior lights Personal/interior lights Personal/interior lights ■ Front Type A On/off Type B On/off ■ Center Type A On/off...
Page 316: Interior Light
3-3. Using the interior lights Personal/interior lights and interior light Type B On/off ■ Rear On/off Interior light DOOR position The interior light comes on when a back door is opened. It turns off when the door is closed.
Page 317: 3-4. Using The Storage Features
3-4. Using the storage features List of storage features Overhead console Glove boxes Auxiliary boxes Bottle holders Cup holders Rear console box (if equipped) Cup holder (if equipped) Front console box • Card holder • Map holder • Pen holder •...
Page 318: Glove Boxes
3-4. Using the storage features Glove boxes CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may result in the following when cabin temperature becomes high: ●...
Page 319: Coin Holder
3-4. Using the storage features Glove boxes and coin holder Pull the lever up. ■ Glove box light The glove box light turns on when the tail lights are on. CAUTION ■ Caution while driving Keep the glove box closed. In the event of sudden braking or sudden swerv- ing, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.
Page 320: Front Console Box
3-4. Using the storage features Coin holder and front console box CAUTION ■ Caution while driving Keep the coin holder closed. Injuries may result in the event of an accident or sudden braking. Front console box Pull the knob up and lift the lid.
Page 321 3-4. Using the storage features Front console box ■ When using the front console box lid as an armrest Pull the knob up and slide the lid forward. If necessary, the console box lid can slide forward. Pull the lid forward by grasping the front of the lid.
Page 322 3-4. Using the storage features Front console box The box can be removed. Hanging file folders can be hung on the rails when the box is removed. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 323: Card Holder
3-4. Using the storage features Card holder Card holder Pull the knob up and lift the lid. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 324: Map Holder
3-4. Using the storage features Map holder Map holder Center console Push the tab down to release the lock. Remove the lid. Stow the lid. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 325 3-4. Using the storage features Map holder Front console box Pull the knob up and lift the lid. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 326: Pen Holder
3-4. Using the storage features Pen holder Pen holder Pull the knob up and lift the lid. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 327: Tissue Pocket
3-4. Using the storage features Tissue pocket Tissue pocket Pull the knob up and lift the lid. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 328: Rear Console Box
3-4. Using the storage features Rear console box Rear console box (if equipped) Upper box Push the knob and lift the lid. Lower box Pull the knob up and lift the upper box.
Page 329 3-4. Using the storage features Rear console box ■ The separator can be used at either of two positions shown in the illus- tration Change the separator position. ■ The separator can be stowed Stow the separator to the lid. ■...
Page 330 3-4. Using the storage features Rear console box ■ The inside tray can be removed Pull the tray up. ■ When closing the rear console box lid Close the rear console box by lifting the grip on the inside of the upper box.
Page 331: Overhead Console
3-4. Using the storage features Rear console box and overhead console CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking. ■ When opening/closing the lower box Be careful not to get your hands or feet caught between the lower box and the upper box.
Page 332 3-4. Using the storage features Overhead console Type B Push the knob forward to open the console. CAUTION ■ Caution while driving Do not leave the overhead console open while driving. Items stored in it may fall out and cause injury.
Page 333: Cup Holders
3-4. Using the storage features Cup holders Cup holders Front Front console box Pull the lid down. Rear...
Page 334 3-4. Using the storage features Cup holders Rear console box (if equipped) Attach the separator when using either console box as a cup holder. Both cup holders cannot be used at the same time. ■ Removing the cup holder (front) Push the tab down to release the lock.
Page 335 3-4. Using the storage features Cup holders Pull the cup holder up. ■ Removing the separator (rear console box) Inside Pull the separator up. Outside Pull the separator up.
Page 336 3-4. Using the storage features Cup holders ■ The position of the separator can be changed (rear console box) Inside Change the separator position. Outside Change the separator position. ■ The separator can be adjusted (rear console box) Adjust the separator.
Page 337: Bottle Holders
3-4. Using the storage features Cup holders and bottle holders CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 338: Auxiliary Boxes
3-4. Using the storage features Bottle holders and auxiliary boxes Rear NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
Page 339 3-4. Using the storage features Auxiliary boxes Rear Pull the lid up. Rear console box (if equipped) Pull the lever up to release the lock. Pull the handle. CAUTION ■ Caution while driving Keep the auxiliary boxes closed. Injuries may result in the event of an accident or sudden braking.
Page 340: 3-5. Using The Other Interior Features
3-5. Using the other interior features Sun visors ■ Main visor Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Side extender: Place in side position then slide backwards. ■ Sub visor (if equipped) Flip down.
Page 341: Vanity Mirrors
3-5. Using the other interior features Vanity mirrors Vehicles without vanity light Open the cover. Vehicles with vanity light Open the cover. The light turns on when the cover is opened. Adjust the brightness of the light.
Page 342: Clock
3-5. Using the other interior features Clock Adjusts the hours. Adjusts the minutes. ■ For quicker adjustment of the clock Hold down the M or H button continuously. This allows faster advancement of the minutes and hours. ■ The clock is displayed when The engine switch is in the ACC or ON position.
Page 343: Outside Temperature Display
3-5. Using the other interior features Outside temperature display Displays the outside air temperature. The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C). Switches the outside air temperature display between °C (Celsius) and °F (Fahrenheit). equipped) Vehicles without multi-informa- tion display:...
Page 344 3-5. Using the other interior features ■ When – –°C or – –°F is displayed The system may be malfunctioning. Take your vehicle to your Toyota dealer. ■ The outside air temperature is displayed when The engine switch is in the ON position.
Page 345: Portable Ashtray
3-5. Using the other interior features Portable ashtray The ashtray can be installed in a cup holder. ■ The ashtray can be removed Pull the ashtray up. CAUTION ■ When not in use Keep the ashtray closed. Injuries may result in the event of sudden braking, sudden swerving or an accident.
Page 346: Cigarette Lighter
3-5. Using the other interior features Cigarette lighter Push the cigarette lighter. The cigarette lighter will pop up when it is ready for use. ■ The cigarette lighter can be used when The engine switch is in the ACC or ON position. CAUTION ■...
Page 347: Conversation Mirror
3-5. Using the other interior features Conversation mirror Push the lid. The mirror can be adjusted by pushing the mirror edge. CAUTION ■ Caution while driving Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
Page 348: Power Outlets
3-5. Using the other interior features Power outlets The power outlet can be used for a following component. 12 V: Accessories that run on less than 10 A. 120 V AC: Accessories that use less than 100 W. Instrument panel (12 V)
Page 349 3-5. Using the other interior features Inside the front console box (12 V) Pull the knob up to release the lock. Lift the lid. Back of the front console box (12 V) : Vehicles without rear seat entertainment system...
Page 350 3-5. Using the other interior features Back of the front console box (120 V AC) Power outlet socket Luggage compartment (12 V) : Vehicles with rear seat entertainment system ■ The power outlet can be used when 12 V The engine switch is in the ACC or ON position. 120 V AC The engine switch is in the ON position.
Page 351 Do not modify, disassemble or repair the power outlet or its inverter, in any way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs. ■...
Page 352 3-5. Using the other interior features NOTICE ■ To avoid damaging the power outlet and the plug ● Close the power outlet lid when not in use. ● Foreign objects or liquids that enter the power outlet may cause a short circuit.
Page 353 If the power outlet is loose when an electrical appliance plug is con- nected Replace the outlet. Contact a Toyota dealer for any necessary replacements. ■ If the power outlet gets dirty Turn the main switch off and use a soft, clean cloth to wipe it gently.
Page 354: Seat Heaters
3-5. Using the other interior features  Seat heaters ■ Front seat The indicator comes on. Adjusts the seat tempera- ture. The further you turn the dial upward, the warmer the seat becomes.  : If equipped...
Page 355 3-5. Using the other interior features ■ Rear seat (vehicles with rear console box) Press the LO or HI switch to warm the seats to a low or high temperature respectively. High temperature The indicator (yellow) comes Low temperature The indicator (green) comes ■...
Page 356 3-5. Using the other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the disabled •...
Page 357: Seat Heaters And Ventilators
3-5. Using the other interior features  Seat heaters and ventilators Blows air from the seats The indicator comes on. The higher the number, the stron- ger the airflow becomes. Heats the seats The indicator comes on. The higher the number, the warmer the seats become.
Page 358 3-5. Using the other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the disabled •...
Page 359: Armrests
3-5. Using the other interior features  Armrests Separated seat Adjusting to the desired angle: Lower the armrest from the highest position to the lowest position. Raise the armrest to the desired angle. Unlock the armrest: Lift the armrest to raise it to the highest position.
Page 360: Rear Side Sunshades
3-5. Using the other interior features  Rear side sunshades Rear door window Pull the tab up. Hook the sunshade onto the anchors. To lower the sunshade, pull the tab slightly to unhook the shade, and lower it slowly.  : If equipped...
Page 361 3-5. Using the other interior features Rear quarter window Pull the tab up. Hook the sunshade onto the anchors. To lower the sunshade, pull the tab slightly to unhook the shade, and lower it slowly. NOTICE ■ To ensure normal operation of the sunshade Observe the following precautions.
Page 362: Assist Grips
3-5. Using the other interior features Assist grips An assist grip (type A) installed on the ceiling can be used to sup- port your body while sitting on the seat. An assist grip (type B) installed on the pillar can be used when get- ting in or out of the vehicle and others.
Page 363: Floor Mat
3-5. Using the other interior features Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eye- lets.
Page 364 When installing the driver’s floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver’s seat. ●...
Page 365: Luggage Compartment Features
3-5. Using the other interior features Luggage compartment features ■ Tie-down hooks Tie-down hooks are provided for securing loose items.
Page 366 3-5. Using the other interior features ■ Cargo net hooks To hang the cargo net, use the cargo net hooks. The cargo net itself is not included as original equipment.
Page 367 3-5. Using the other interior features ■ Shopping bag hooks To hang shopping bags, use the shopping bag hooks.
Page 368 3-5. Using the other interior features ■ Auxiliary boxes Type A Pull the lever upwards to lift the deck board. Type B (if equipped) Open the cover.
Page 369 3-5. Using the other interior features CAUTION ■ When the tie-down hooks are not in use To avoid injury, always return the tie-down hooks to their retracted positions when they are not in use. ■ Caution while driving Keep the auxiliary box closed. Injuries may result in the event of an accident or sudden braking.
Page 370: Garage Door Opener
3-5. Using the other interior features  Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices. ® The garage door opener (HomeLink Universal Transceiver) is manufac- ®...
Page 371 3-5. Using the other interior features Press and hold down one of the ® buttons on the HomeLink the button on the transmitter. When indicator ® HomeLink changes from a slow to a rapid flash, you can release both buttons. ®...
Page 372 3-5. Using the other interior features ■ Programming a Rolling Code system (for U.S.A. owners) If your device is Rolling Code equipped, follow the steps under the ® heading “Programming the HomeLink ” before proceeding with the steps listed below. Locate the training button on the ceiling mounted garage door opener motor.
Page 373 ® the remaining HomeLink buttons. ■ Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. ■ Reprogramming a button ® The individual HomeLink buttons cannot be erased but can be reprogrammed.
Page 374 3-5. Using the other interior features ® Erasing the entire HomeLink memory (all three programs) Press and hold down the 2 out- side buttons for 10 seconds until the indicator flashes. If you sell your vehicle, be sure to erase the programs stored in the ®...
Page 375 3-5. Using the other interior features ■ When support is necessary Visit on the web at www.homelink.com or call 1-800-355-3515. CAUTION ■ When programming a garage door or other remote control device The garage door may operate, so ensure that people and objects are out of danger to prevent potential harm.
Page 376: Compass
3-5. Using the other interior features  Compass The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation To turn the compass on or off, press the switch. ■ Displays and directions Display Direction North...
Page 377 3-5. Using the other interior features Calibrating the compass Samoa: 5 Guam: 8 Saipan: 8 The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
Page 378 3-5. Using the other interior features ■ Deviation calibration Stop the vehicle where it is safe to drive in a circle. Press the switch until a number (1 to 15) appears on the com- pass display. Press the switch, and referring to the map above, select the number of the zone where you are.
Page 379 3-5. Using the other interior features ■ Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions: ● The vehicle is stopped immediately after turning. ● The vehicle is on an inclined surface. ●...
Page 380 3-5. Using the other interior features...
Page 381: Maintenance And Care
Maintenance and care 4-1. Maintenance and care Cleaning and protecting the vehicle exterior..382 Cleaning and protecting the vehicle interior..385 4-2. Maintenance Maintenance requirements ....388 General maintenance..391 Emission inspection and maintenance (I/M) programs ......394 4-3. Do-it-yourself maintenance Do-it-yourself service precautions ....
Page 382: Cleaning And Protecting The Vehicle Exterior
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 383 ■ Precaution regarding the Blind Spot Monitor If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, consult your Toyota dealer.
Page 384 4-1. Maintenance and care NOTICE ■ To prevent paint deterioration and corrosion on the body and compo- nents (aluminum wheels etc.) ● Wash the vehicle immediately in the following cases: • After driving near the sea coast • After driving on salted roads •...
Page 385: Cleaning And Protecting The Vehicle Interior
4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
Page 386 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 387 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. ●...
Page 388: 4-2. Maintenance
■ Repair and replacement It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 389 Continue to press and hold the button until “MAINT REQD RESET MODE COMPLETE” appears on the multi-information display. ■ Allow inspection and repairs to be performed by a Toyota dealer ● Toyota technicians are well-trained specialists and are kept up to date with the latest service information.
Page 390 4-2. Maintenance CAUTION ■ Warning in handling of battery ● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
Page 391: General Maintenance
“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
Page 392 4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be held securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 393 4-2. Maintenance Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? Tire •...
Page 394: Emission Inspection And Maintenance (I/M) Programs
If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
Page 395: 4-3. Do-It-Yourself Maintenance
• FMVSS No.116 DOT 3 or SAE Brake fluid level (P. 407) J1703 brake fluid • Rag or paper towel • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 396 4-3. Do-it-yourself maintenance Items Parts and tools • Bulb with same number and watt- age rating as original Light bulbs (P. 447) • Phillips-head screwdriver • Flathead screwdriver • Automatic transmission fluid ® DEXRON II or III Power steering fluid level •...
Page 397 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothing, and tools away from the moving fan and engine drive belt.
Page 398 4-3. Do-it-yourself maintenance NOTICE ■ If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. ■ If the brake fluid level is low or high It is normal for the brake fluid level to go down slightly as the brake pads wear or when the brake fluid level in the accumulator is high.
Page 399: Hood
4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood lock release lever. The hood will pop up slightly. Pull up the hood catch lever and lift the hood. CAUTION ■...
Page 400: Engine Compartment
4-3. Do-it-yourself maintenance Engine compartment Washer fluid tank (P. 413) Brake fluid reservoir (P. 407) Engine oil level dipstick (P. 401) Fuse box (P. 435) Engine coolant reservoir Battery (P. 410) (P. 405) Radiator (P. 407) Engine oil filler cap Cooling fans (P.
Page 401 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After turning off the engine, wait more than 5 minutes for the oil to drain back into the bot- tom of the engine.
Page 402 4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 403 4-3. Do-it-yourself maintenance ■ Engine oil consumption A certain amount of engine oil will be consumed while driving. In the follow- ing situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals. ●...
Page 404 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 405 If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system. ■...
Page 406 4-3. Do-it-yourself maintenance CAUTION ■ When the engine is hot Do not remove the radiator cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns. NOTICE ■...
Page 407 Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION ■...
Page 408 4-3. Do-it-yourself maintenance CAUTION ■ When filling the reservoir Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately.
Page 409 4-3. Do-it-yourself maintenance Power steering fluid ■ Fluid level The fluid level should be within the appropriate range. Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot) Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures.
Page 410 4-3. Do-it-yourself maintenance CAUTION ■ Checking the fluid level Take care, as the reservoir may be hot. NOTICE ■ When adding fluid Avoid overfilling, or the power steering may be damaged. ■ After replacing the reservoir cap Check the steering box case, vane pump and hose connections for leaks or damage.
Page 411 4-3. Do-it-yourself maintenance ■ Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: ● If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable. ● Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
Page 412 4-3. Do-it-yourself maintenance CAUTION ■ Emergency measures regarding electrolyte ● If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
Page 413 4-3. Do-it-yourself maintenance Washer fluid Add washer fluid in the following situations. ● The washer does not work. ● The low washer fluid warning light comes on. (vehicles without multi-information display) ● The warning message appears on the multi-information display. (vehicles with multi-information display) Open the lid.
Page 414 4-3. Do-it-yourself maintenance CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE ■...
Page 415: Tires
4-3. Do-it-yourself maintenance Tires Replace or rotate tires in accordance with maintenance sched- ules and treadwear. ■ Checking tires Check if the treadwear indicators are showing on the tires. Also check the tires for uneven wear, such as excessive wear on one side of the tread.
Page 416 ■ The tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (P. 472)
Page 417 ID codes must be regis- tered in the tire pressure warning computer and tire pressure warning system must be initialized. Have tire pressure warning valve and trans- mitter ID codes registered by your Toyota dealer. (P. 418) Initializing the tire pressure warning system ■...
Page 418 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer.
Page 419 4-3. Do-it-yourself maintenance ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light comes on after blinking for 1 minute to indicate a system malfunction.
Page 420 Initialization can be completed in several minutes. However, in the fol- lowing cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●...
Page 421 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 422 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 423: Tire Inflation Pressure
4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (P. 528)
Page 424 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.
Page 425 Reduced tire life due to wear ● Reduced safety ● Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ●...
Page 426 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. If the tires are not properly inflated, the following conditions may occur which could lead to an accident resulting in death or serious injury: ●...
Page 427: Wheels
● Bent wheels that have been straightened ■ Wheel precautions ● Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).
Page 428 ■ When replacing wheels The wheels of your Toyota are equipped with tire pressure warning valves and transmitters (except for spare tire) that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure.
Page 429 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 430: Air Conditioning Filter
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Replacement method Turn the engine switch off. Open the glove box. Remove the internal tray. Remove the inside cover by sliding up while pulling toward you.
Page 431 4-3. Do-it-yourself maintenance Remove the filter cover. Pull the filter out of the filter outlet. Remove the air conditioning filter and replace it with a new one. The“UP” marks shown on the filter should be pointing up.
Page 432 4-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) ■...
Page 433: Wireless Remote Control Battery
4-3. Do-it-yourself maintenance Wireless remote control battery Replace the battery with a new one if it is discharged. ■ You will need the following items: Lithium battery CR2032 ■ Replacing the battery Remove the cover using a coin protected with tape etc. Remove the discharged trans- mitter battery.
Page 434 ● The operational range is reduced. ■ Use a CR2032 lithium battery ● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. ● Replace only with the same or equivalent type recommended by your Toyota dealer. ●...
Page 435: Checking And Replacing Fuses
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch off. The fuses are located in the following places. To check the fuses, follow the instructions below.
Page 436 4-3. Do-it-yourself maintenance Remove the fuse with the pull- out tool.
Page 437 Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type C Normal fuse Blown fuse Contact your Toyota dealer.
Page 438 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment Fuse Ampere Circuit Multiport fuel injection system/ 15 A sequential multiport fuel injection system HORN 10 A Horn Multiport fuel injection system/ EFI NO.1 25 A sequential multiport fuel injection system IG2 MAIN 30 A...
Page 439 4-3. Do-it-yourself maintenance Fuse Ampere Circuit POWER NO.4 25 A Power windows 15 A Front fog lights Stop lights, high mounted stop- light, vehicle stability control sys- tem, anti-lock brake system, shift STOP 15 A lock system, multiport fuel injection system/sequential multiport fuel injection system, towing converter TOW BRK...
Page 440 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiplex communication system, Multiport fuel injection system/ sequential multiport fuel injection system, auto anti-glare inside rear ECU-B1 7.5 A view mirror, power front driver’s seat, power tilt and power tele- scopic, power back door, gateway Interior lights, personal lights, van- ity lights, engine switch light, foot DOME...
Page 441 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Electronically modulated air sus- AIR SUS NO.2 7.5 A pension system SPARE Spare fuse SPARE 15 A Spare fuse SPARE 30 A Spare fuse Electronically modulated air sus- AIR SUS 50 A pension system 30 A Power back door RR HTR...
Page 442 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiport fuel injection system/ A/PUMP NO.2 50 A sequential multiport fuel injection system HEAD LL, HEAD RL, MAIN 40 A HEAD LH, HEAD RH fuses : Replace the fuse with one of the same ampere rating as the original.
Page 443 4-3. Do-it-yourself maintenance ■ Under the instrument panel Fuse Ampere Circuit INVERTER 15 A Power outlet (120 V) FR P/SEAT LH 30 A Power front driver’s seat DR/LCK 25 A Multiplex communication system POWER No.5 30 A Power back door 7.5 A On-board diagnosis system PWR OUTLET...
Page 444 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Anti-lock brake system, vehicle sta- bility control system, multiplex com- munication system, intuitive parking assist system, power front driver’s seat, power tilt and power ECU-IG No.1 7.5 A telescopic, shift lock, tire pressure warning system, accessory meter, trailer towing, power outlet, electric moon roof, power back door, head light cleaner, Blind Spot Monitor...
Page 445 (P. 447) ● If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer. ■ If there is an overload in the circuits The fuses are designed to blow, protecting the wiring harness from damage.
Page 446 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. ● Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix. ●...
Page 447: Light Bulbs
You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 448 4-3. Do-it-yourself maintenance ■ Rear bulb locations Stop/tail and rear side marker lights Tail lights License plate lights Rear turn signal lights Back-up lights Replacing light bulbs ■ Headlight high beam Unplug connector while depressing the lock release.
Page 449 4-3. Do-it-yourself maintenance Turn the bulb base counterclock- wise. ■ Headlight low beam Unplug connector while depressing the lock release. Turn the bulb base counterclock- wise.
Page 450 4-3. Do-it-yourself maintenance ■ Front turn signal/parking lights and daytime running lights (if equipped) Turn the bulb base counterclock- wise. Remove the light bulb.
Page 451 4-3. Do-it-yourself maintenance ■ Front side marker lights Remove the fender liner clip. Partly remove the fender liner and turn the bulb base counter- clockwise.
Page 452 4-3. Do-it-yourself maintenance Remove the light bulb. ■ Front fog lights (if equipped) Remove the bolts and partly remove the fender liner. Unplug connector while depressing the lock release. Turn the bulb counterclockwise.
Page 453 4-3. Do-it-yourself maintenance ■ Stop/tail and rear side marker lights, rear turn signal lights Right side Open the back door and remove the cover. To protect the cover, place a rag between the flathead screwdriver or equivalent and cover as shown in the illustrations.
Page 454 4-3. Do-it-yourself maintenance Left side (vehicles with speaker in the luggage) Open the back door and remove the cover. To protect the cover, place a rag between the flathead screwdriver or equivalent and cover as shown in the illustrations. Turn the bulb bases counter- clockwise.
Page 455 4-3. Do-it-yourself maintenance Tail lights, back-up lights Remove the covers. (vehicles with power back door only) To protect the cover, place a rag between the flathead screwdriver or equivalent and cover as shown in the illustrations. Remove the nuts. Remove the rear combination light assembly in the order shown in the illustration.
Page 456 4-3. Do-it-yourself maintenance Turn the bulb base counterclock- wise. Tail light Back-up light Remove the light bulb. Tail light Back-up light ■ License plate lights Remove the screws and light unit.
Page 457 LED high mounted stoplight and side turn signal light The high mounted stoplight and side turn signal light consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.
Page 458 4-3. Do-it-yourself maintenance CAUTION ■ Replacing light bulbs ● Turn off the headlights. Do not attempt to replace the bulb immediately after turning off the headlights. The bulbs become very hot and may cause burns. ● Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb.
Page 459 When trouble arises 5-1. Essential information 5-2. Steps to take in an emergency Emergency flashers ..460 If a warning light turns on If your vehicle needs to or a warning buzzer be towed ......461 sounds......469 If you think something is If a warning message is wrong ......
Page 460: 5-1. Essential Information
5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when the engine is not running.
Page 461: If Your Vehicle Needs To Be Towed
If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or commercial towing service, using a wheel-lift type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 462 5-1. Essential information Towing with a wheel-lift type truck From the front Use a towing dolly under the rear wheels. From the rear Use a towing dolly under the front wheels. Using a flatbed truck If your is transported by a vehicle Front flatbed truck, it should be tied...
Page 463 5-1. Essential information Vehicles without electronically modulated air suspension If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45. Do not overly tighten the tie downs or the vehicle may be damaged.
Page 464 5-1. Essential information Emergency towing procedure TYPE A Securely attach cables or chains to the towing hooks. Take care not to damage the vehicle body. TYPE B Securely attach cables or chains to the towing hooks. Take care not to damage the vehicle body.
Page 465 5-1. Essential information CAUTION Observe the following precautions. Failure to do so may result in death or serious injury. ■ When towing the vehicle 2WD models: Be sure to transport the vehicle with all four wheels raised off the ground. If the vehicle is towed with the tires contacting the ground, the drivetrain and related parts may be damaged or an accident may occur due to a change in...
Page 466 5-1. Essential information NOTICE ■ To prevent damage to the vehicle when towing using a wheel-lift type truck ● Do not tow the vehicle from the rear when the engine switch is in the LOCK position or the key is removed. The steering lock mechanism is not strong enough to hold the front wheels straight.
Page 467: If You Think Something Is Wrong
5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 468: Fuel Pump Shut Off System
5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 469: Steps To Take In An Emergency If A Warning Light Turns On Or A Warning Buzzer Sounds
Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Charging system warning light Indicates a malfunction in the vehicle’s charging sys-...
Page 470 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: •...
Page 471 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light (warning buzzer) Check that all doors are Indicates that a door or closed.
Page 472 If the light does not go off, contact your Toyota dealer. When the light flashes: Have the system Indicates a malfunction in checked by your Toyota the automatic transmis- dealer. sion system. Tire pressure warning light When the light comes on:...
Page 473 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Low fuel level warning light Refuel the vehicle. Low level of fuel. Low washer fluid warn- ing light Fill the tank. Low level of washer fluid. Maintenance required reminder light Indicates that mainte- nance is required accord-...
Page 474 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Master warning light A buzzer sounds and the warning light comes on P. 480 and flashes to indicate that the master warning system has detected a malfunction. : Open door warning buzzer: The buzzer sounds to indicate that any door is opened (with the vehicle hav- ing reached a speed of 3 mph [5 km/h])
Page 475 Is the fuel tank cap loose? If it is, tighten it securely. The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible. ■...
Page 476 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. ● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) ●...
Page 477 ON position, have it checked by your Toyota dealer. ■ Customization that can be configured at Toyota dealer The vehicle speed linked seat belt reminder buzzer can be disabled. (Customizable features P. 539) CAUTION ■...
Page 478 5-2. Steps to take in an emergency CAUTION ■ Maintenance of the tire Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 479 5-2. Steps to take in an emergency CAUTION TPMS (tire pressure warning system) malfunctions may occur for a vari- ety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS (tire pressure warning system) from functioning properly.
Page 480: If A Warning Message Is Displayed (Vehicles With Multi-Information Display)
Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning message Details Indicates that the engine coolant temperature is too high A buzzer also sounds.
Page 481 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning message goes off. Warning message Details Correction procedure Indicates that one or more of the doors is not fully closed.
Page 482 If the light goes off, temperature is too high you may start the A buzzer also sounds. vehicle again. If the light does not go off, contact your Toyota dealer. Indicates a malfunction Have the system in the automatic trans- checked by your Toy- mission system ota dealer.
Page 483 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that all mainte- nance according to the driven distance on the maintenance schedule should be performed If necessary, perform soon. maintenance. Comes on approximately 4500 miles (7200 km) after (U.S.A.
Page 484 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the laser radar sensor is dirty or Clean the sensor. covered with ice. (if equipped) A buzzer also sounds. Indicates that the dynamic laser cruise If the windshield wipers control system is unable are on, turn them off or to judge vehicle-to-vehi-...
Page 485 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the Blind Spot Monitor sensor is Clean the sensor. dirty or covered with ice. A buzzer also sounds. Indicates that the Blind (if equipped) Spot Monitor sensor has Wait for sensor to cool been exposed to very down or warm up.
Page 486: If You Have A Flat Tire
5-2. Steps to take in an emergency If you have a flat tire Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ●...
Page 487 5-2. Steps to take in an emergency Taking out the jack and tool bag Pull the deck board up. Remove the cover and loosen the strap. Remove the tools. Tighten Loosen...
Page 488 5-2. Steps to take in an emergency Taking out the spare tire Assemble the jack handle exten- sion as shown. Remove the cover. Insert the end of the jack handle extension into lowering screw and turn it counterclock- wise. After the tire is lowered com- pletely to the ground, remove the holding bracket.
Page 489 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Wheel Flat tire chock positions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of Left- the front...
Page 490 5-2. Steps to take in an emergency Position the jack at the correct jack point as shown. Front Rear Front Make sure the jack is positioned on a level and solid place. Raise the vehicle until the tire is slightly raised off the ground. Remove all the wheel nuts and the tire.
Page 491 5-2. Steps to take in an emergency Install the tire and loosely tighten each wheel nut by hand by approximately the same amount. Tighten the nuts until the tapered Tapered portion portion comes into loose contact with the disc wheel. Disc wheel Lower the vehicle.
Page 492 5-2. Steps to take in an emergency CAUTION ■ Stowing the flat tire Failure to follow steps listed under stowing the tire may result in damage to the spare tire carrier and loss of the tire, which could result in serious injury or death.
Page 493 5-2. Steps to take in an emergency Confirm that the tire is not loose after tightening: Push and pull the tire Try rotating Visually check to ensure the tire is not hung on surrounding parts. If looseness or misassembly exists, repeat step 2 and step 3. Repeat step 3 any time the tire is lowered or disturbed.
Page 494 5-2. Steps to take in an emergency CAUTION ■ Using the jack handle Insert the square head securely until you hear a click to prevent the extension parts from coming apart unexpectedly. ■ Replacing a flat tire Observe the following precautions to reduce the risk of death or serious injury.
Page 495 5-2. Steps to take in an emergency CAUTION ■ Speed limit when using the temporary spare tire Do not drive at speeds in excess of 50 mph (80 km/h) when a temporary spare tire is installed on the vehicle. The temporary spare tire is not designed for driving at high speeds. Fail- ing to observe this precaution may lead to an accident causing death or serious injury.
Page 496 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 497: If The Engine Will Not Start
5-2. Steps to take in an emergency If the engine will not start If the engine still does not start after following the correct starting procedure (P. 158) or releasing the steering lock (P. 159), confirm the following points. ■ The engine will not start even when the starter motor oper- ates normally.
Page 498 One of the following may be the cause of the problem. ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. (P. 501) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
Page 499: If The Shift Lever Cannot Be Shifted From P
(a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 500: If You Lose Your Keys
5-2. Steps to take in an emergency If you lose your keys New genuine Toyota keys can be made by your Toyota dealer using one of the master keys and the key number stamped on your key number plate. (P. 30) ■...
Page 501: If The Vehicle Battery Is Discharged
You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. Confirm that the key and wire- less remote control are being carried.
Page 502 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible. ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting.
Page 503 5-2. Steps to take in an emergency CAUTION ■ Avoiding battery fires or explosions Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery. ● Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended termi- nal.
Page 504: If Your Vehicle Overheats
(radia- tor) for any leaks. Radiator Cooling fan If a large amount of coolant leaks, immediately contact your Toyota dealer. The coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir.
Page 505 If the fan is not operating: Stop the engine immediately and contact your Toyota dealer. If the fan is operating: Have the vehicle inspected at the nearest Toyota dealer. CAUTION ■ To prevent an accident or injury when inspecting under the hood of your vehicle ●...
Page 506 5-2. Steps to take in an emergency NOTICE ■ When adding engine coolant Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine. ■...
Page 507: If The Vehicle Becomes Stuck
5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. Stop the engine. Set the parking brake and put the shift lever in P.
Page 508 5-2. Steps to take in an emergency NOTICE ■ To avoid damaging the transmission and other components ● Avoid spinning the wheels and do not rev the engine. ● If the vehicle remains stuck after trying these procedures, the vehicle may require towing to be freed.
Page 509: If Your Vehicle Has To Be Stopped In An Emergency
5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmly depress it.
Page 510 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 511: Vehicle Specifications
Vehicle specifications 6-1. Specifications Maintenance data (fuel, oil level, etc.) ..512 Fuel information ....523 Tire information ....528 6-2. Customization Customizable features ..539 Items to initialize ....543...
Page 512: Specifications Maintenance Data (Fuel, Oil Level, Etc.)
6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions Overall length 205.1 in. (5210 mm) Overall width 79.9 in. (2030 mm) Overall height 77.0 in. (1955 mm) Wheelbase 122.0 in. (3100 mm) Front tread 67.9 in. (1725 mm) Rear tread 69.1 in.
Page 513 6-1. Specifications Weight Vehicle capacity Driving Model code Engine weight system (Trailer weight + cargo) (Occupants+luggage) USK60L-GKTSKA 1310 lb. (590 kg) 7400 lb. (3357 kg) 1330 lb. (600 kg) USK60L-GKTLKA 7300 lb. (3311 kg) 5.7L V8 1315 lb. (595 kg) USK60L-GKTZKA 7200 lb.
Page 514 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 515 6-1. Specifications Engine Model 3UR-FE and 3UR-FBE Type 8-cylinder V-type, 4-cycle, gasoline 3.70  4.02 in. (94.0  102.0 mm) Bore and stroke Displacement 345.6 cu.in. (5663 cm Valve clearance Automatic adjustment (engine cold) Drive belt tension Automatic adjustment Fuel Model 3UR-FE engine 3UR-FBE engine...
Page 516 ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toy- ota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC GF-5 multigrade engine oil...
Page 517 13.1 qt. (12.4 L, 10.9 Imp.qt.) Capacity Vehicles with towing package 14.1 qt. (13.3 L, 11.7 Imp.qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 518 Oil type and viscosity LT 75W-85 GL-5 or equivalent : Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent of matching quality to satisfy the above specification. Please con-...
Page 519 NOTICE ■ Automatic transmission fluid type Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmis- sion of your vehicle.
Page 520 6-1. Specifications Brakes Pedal clearance 4.1 in. (104 mm) Min. 0.04  0.24 in. (1  6 mm) Pedal free play Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in. (1.0 mm) Parking brake pedal travel 6 —...
Page 521 6-1. Specifications Tires and wheels Type A P275/65R18 114T, Tire size P255/70R18 112T (spare tire) Front tires: 33 psi (230 kPa, 2.3 kgf/cm or bar) Tire inflation pressure Rear tires: (Recommended cold tire 33 psi (230 kPa, 2.3 kgf/cm or bar) inflation pressure) Spare tire: 33 psi (230 kPa, 2.3 kgf/cm...
Page 522 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights 9005 (high beam) Headlights — (low beam) Front fog lights 9145 Front side marker lights Front turn signal/parking 4157NAK 27/8 lights Exterior Rear turn signal lights — Stop/tail and rear side 7443 21/5 marker lights...
Page 523: Fuel Information
6-1. Specifications Fuel information Gasoline engine (P. 515) You must only use unleaded gasoline. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A.
Page 524 In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer. ■...
Page 525 EPA’s lowest additives con- centration program. ● Toyota strongly recommends the use of Top Tier Detergent Gasoline. For more information on Top Tier Detergent Gasoline and a list of marketers, please go to the official website www.toptiergas.com.
Page 526 Non-recommendation of the use of gasoline containing MMT Some gasoline contains an octane enhancing additive called MMT (Methyl- cyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected.
Page 527 6-1. Specifications NOTICE ■ When use of non-specified fuels (Flex-fuel engine) The use of non-specified fuels will have a negative impact on starting and driving performance, and will cause damage to the fuel system components. Therefore, do not add fuels such as the following. •...
Page 528: Tire Information
6-1. Specifications Tire information Typical tire symbols Tire size (P. 530) DOT and Tire Identification Number (TIN) (P. 529) Location of treadwear indicators (P. 415) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Page 529 6-1. Specifications Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. Summer tire or all season tire (P. 419) An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.
Page 530 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol...
Page 531 U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 532 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
Page 533 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.
Page 534 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb.
Page 535 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 536 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on Intended outboard the other sidewall of the tire, or sidewall...
Page 537 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between adja- Ply separation cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, Pneumatic tire when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load...
Page 538 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear indica- designed to give a visual indication of the...
Page 539: 6-2. Customization
Programming these preferences requires specialized equipment and may be performed by an autho- rized Toyota dealership. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customized Item Function...
Page 540 6-2. Customization Customized Item Function Default setting setting Wireless Push twice remote con- Power back door oper- Push and hold trol ation One short  P. 31) push Switch operation Push and hold One short push Wireless remote control linked operation Operation signal vol- Power back Operation when door...
Page 541 6-2. Customization Customized Item Function Default setting setting Driver’s door unlocked in All doors Door lock one step, all Unlocking using a key unlocked in (P. 35) doors one step unlocked in two steps Open only Power Door key linked opera- windows Open and close Close only...
Page 542 6-2. Customization Customized Item Function Default setting setting 7.5 seconds Time elapsed before 15 seconds lights turn off 30 seconds Illumination Operation after the  P. 313) engine is off Operation when the doors are unlocked Seat Belt Vehicle speed linked Reminder seat belt reminder Buzzer...
Page 543: Items To Initialize
6-2. Customization Items to initialize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item When to initialize Reference • After reconnecting or changing Power back door the battery.
Page 544 6-2. Customization...
Page 545: For Owners
For owners Reporting safety defects for U.S. owners ....546 Seat belt instructions for Canadian owners (in French) ..... 547 SRS airbag instructions for Canadian owners (in French) ..... 550...
Page 546: Reporting Safety Defects For U.s. Owners
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 547: Seat Belt Instructions For Canadian Owners (In French)
Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.
Page 550: Srs Airbag Instructions For Canadian Owners (In French)
SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English.
Page 559: Index
Index Abbreviation list ..... 560 Alphabetical index....562 What to do if......573 For vehicles with Entune Audio Plus or Entune Premium Audio, refer to the “NAVIGATION SYSTEM OWNER’S MANUAL” for information regarding the multimedia system. Multimedia system types: P. 310...
Page 560: Abbreviation List
Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Two Wheel Drive Four Wheel Drive Anti-Lock Brake System Accessory AI-SHIFT Artificial Intelligence shifting Automatic Locking Retractor A-TRAC Active Traction Control AUTO LSD Automatic Limited Slip Differential Adaptive Variable Suspension System Blind Spot Monitor Child Restraint System Electronic Control Unit Event Data Recorder...
Page 561 Abbreviation list ABBREVIATIONS MEANING Power Supplemental Restraint System Tire Identification Number TPMS Tire Pressure Warning System TRAC Traction Control Treadwear indicators Trailer Weight Rating Vehicle Identification Number Vehicle Stability Control...
Page 562: Alphabetical Index
Alphabetical index Alphabetical index A/C........294, 303 Alarm......... 107 AAC disc Antenna ABS ...........246 Anti-lock brake system ... 246 Active traction control.....246 Armrest ........359 Adaptive variable suspension Ashtrays ........345 system ........238 Assist grips ......362 Air conditioning filter....430 A-TRAC ........246 Air conditioning system Audio input.......
Page 563 Alphabetical index Back-up lights Front passenger occupant Replacing light bulbs .... 447 classification system ...124 Wattage ........ 522 Infant seats, definition ...129 Back door Infant seats, installation..138 Back door ....... 40 Installing CRS with LATCH Back window ......93 system ........135 Wireless remote control..
Page 564 Alphabetical index Cooling system Electronically modulated air Engine overheating ....504 suspension ......233 CRS ...........129 Emergency flashers Cruise control Switch ........460 Cruise control ......202 Emergency, in case of Dynamic laser cruise If the engine will not start ..497 control .........206 If the shift lever cannot be Cup holders ......333...
Page 565 Alphabetical index Engine FFV ........100, 523 Compartment......400 Flex-fuel ......100, 523 Engine switch ....... 158 Flexible fuel vehicle ..100, 523 Hood........399 Floor mat........363 How to start the Fluid engine ........ 158 Brake........407 Identification number .... 514 Washer........413 If the engine will not start..497 Fog lights Ignition switch ......
Page 566 Alphabetical index Garage door opener....370 I/M test ........394 Gas station information...576 Identification Gauges........168 Engine........514 Glove box........318 Vehicle ........514 Ignition switch......158 Illuminated entry system..313 Hands-free system Indicator lights ......173 (for cellular phone) Initialization Hazard lights Items to initialize ....543 Switch........460 Inside rear view mirror ....81 Head restraints...
Page 567 Alphabetical index LATCH system......135 Maintenance License plate lights Do-it-yourself Replacing light bulbs .... 447 maintenance .......395 Wattage ........ 522 General maintenance....391 Light bulbs Maintenance data....512 Replacing ......447 Maintenance requirements..388 Wattage ........ 522 Reset the maintenance Lights data........389 Door courtesy lights....313 Map holder........324 Emergency flasher switch ..
Page 568 Alphabetical index Noise from under vehicle ..23 Parking assist ......220 Parking brake ......166 Parking lights Odometer ........168 Replacing light bulbs..... 447 Off-road precautions ....254 Switch ........187 Wattage......... 522 Engine oil ......401 Pen holder ........ 326 Opener Personal lights Back door ........40 Switch ........
Page 569 Alphabetical index Radiator........407 Seat belts Radio Adjusting the seat belt.....69 Rear air conditioning ALR .........74 system ........303 Automatic Locking Rear console box ....328 Retractor .......74 Rear seat Child restraint system Adjustment ......51 installation......133 Folding down second Cleaning and maintaining seatback.......
Page 570 Alphabetical index Service reminder Stop lights indicators ......173 Replacing light bulbs..... 447 Shift lever Wattage......... 522 Automatic Storage feature ......317 transmission......161 Storage precautions ....261 If the shift lever cannot Stuck be shifted from P....499 If your vehicle becomes Shift lock system .....499 stuck ........
Page 571 Alphabetical index Tachometer......168 Tissue pocket ......327 Tail lights Tools .........486 Replacing light bulbs .... 447 Total load capacity....264 Switch........187 Towing Wattage ........ 522 Dinghy towing......290 Talk switch Emergency towing....461 Telephone switch Trailer towing......270 Theft deterrent system Trailer weight rating..272, 513 Alarm ........
Page 572 Alphabetical index Warning buzzers Weight Brake system ......469 Cargo capacity ...... 259 Open door ......471 Load limits......264 Seat belt reminder....471 Towing capacity ....513 Warning lights Trailer Weight Rating ..275, 513 ABS ........470 TWR......275, 513 Airbag system .......470 Vehicle capacity weight..
Page 573: What To Do If
What to do if... What to do if... A tire punctures If you have a flat tire P. 486 P. 497 If the engine will not start The engine does not start P. 105 Engine immobilizer system P. 501 If the vehicle battery is discharged If the shift lever cannot be shifted The shift lever cannot be P.
Page 574 What to do if... The warning light or indicator If a warning light turns on P. 469 light comes on ■ Instrument cluster Vehicles with multi-information display Vehicles without multi-information display ■ Center panel...
Page 575: Warning Lights
What to do if... ■Warning lights Brake system warning Low washer fluid light warning light P. 473 Power steering warning P. 469 light P. 470 Charging system warning Master warning light light P. 469 P. 474 Malfunction indicator Slip indicator lamp P.
Page 576: Gas Station Information
GAS STATION INFORMATION Auxiliary catch lever Fuel filler door P. 399 P. 100 Hood lock release lever Tire inflation pressure P. 399 P. 521 Fuel tank capacity 26.4 gal. (100.0 L, 22.0 lmp.gal.) (Reference) Fuel type P. 515 Cold tire inflation P.

Toyota 2016 Sequoia Manual

1 Before Driving

1-1. Key Information

1-2. Opening, Closing and Locking the Doors

Adjustable Components (Seats, Mirrors, Steering Wheel)

1-4. Opening and Closing the Windows and Moon Roof

Refueling Opening the Fuel Tank Cap

1-6. Theft Deterrent System

1-7. Safety Information

2 When Driving

2-1. Driving Procedures

Instrument Cluster Gauges and Meters

Operating the Lights and

2-4. Using Other Driving Systems

2-5. Driving Information

Interior Features

Using the Air Conditioning

3-2. Using the Multimedia System

3-3. Using the Interior Lights

3-4. Using the Storage Features

3-5. Using the Other Interior Features

4 Maintenance and Care

Maintenance Requirements

4-3. Do-It-Yourself Maintenance

5-1. Essential Information

Steps to Take in an Emergency if a Warning Light Turns on or a Warning Buzzer Sounds

Vehicle Specifications

Specifications Maintenance Data (Fuel, Oil Level, Etc.)

6-2. Customization

For Owners

Index

Abbreviation List

Alphabetical Index

What to Do if

Quick Links

Related Manuals for Toyota 2016 Sequoia

Summary of Contents for Toyota 2016 Sequoia