Menu Interface; Table - Lennox LGH 036 Installation Instructions Manual

Menu Interface

Table 2 shows the major levels of the menu interface. Many
of these options have more levels and are described in the
following sections that detail DISPLAY, SERVICE, DATA,
and SETTINGS.
Use rectangular button
next menu level (i.e. Level 1 to Level 2).
Use A to "back up" to the next higher menu level (i.e.
Level 2 to Level 1).
Use YB to move (scroll) within a menu level; also use to
change values of selected item.
Table 2. Menu Interface
Level 1 Level 2
NOTE - Features and options not currently available are greyed out in
the manual and will show a message of "N/A" on the display
ALARM
ALARMS
(multiple)
MODE
(dis­
play
area)
LonTalk
USB
TEST
OFFLINE
SER­
VICE
IN / OUT­
PUTS
REPLACE
SOFT­
WARE RE­
COVERY
(ENTER) or " to progress to
Level 3
SILENCE (push ENTER button to silence)
SILENCE ALL (push ENTER button to silence all
alarms; or push " to view alarms and YB to
scroll thru description list.)
COMP LOAD LOW AMBIENT
SHEDDING LOCKOUT
MORNING
COOLING
WARMUP
DEHUMIDIFICA­
M2 FAILED TO
TION
RESPOND
FAN ONLY
M2 RESET
FREE COOLING
OFF ON ALARM
FRESH AIR COOL
PRE-COOL
FRESH AIR HEAT
PRE INSTALL
HEATING
RESTARTING..
HVAC OFF
SMOKE
IDLE TEST
NEURON ID
XX:XX:XX:XX:XX:XX
WRITING USB
WRITING ALARM/STATUS LOG
USB COMPLETE
UPDATE FIRMWARE (For versions
1.09 xx H and later)
GUIDED (N/A)
BLOWER
FANS
COOL
HEAT
DAMPER
HUMIDITROL
MGV
VAV
SENSORS
OUTPUTS
CONTROLLER
LOCKOUT
BLOWER ONLY (N/A)
COOLING ONLY (N/A)
HEATING ONLY (N/A)
RESET
THERMOSTAT
ZONING (N/A)
SENSORS
RELAYS
NETWORK
FILTER
BELT
UV LAMP
FANS
BLOWER
COMPRESSOR
UPDATE M2 SOFTWARE
UPDATE DB1 SOFTWARE
(FOR DB VERSIONS 1.09H AND
LATER ONLY)
Table 2. Menu Interface (cont'd)
Level 1 Level 2
RUNTIMES
HISTORY
SENSORS
(also ac­
cessible
thru In /
DATA
Outputs)
NETWORK
FACTORY
STATUS
UNIT
SET­
POINTS
CONTROL
SET­
TINGS
OPTIONS
INSTALL
Page 6
Level 3
POWER ON
FILTER: XX HRS
BELT: XX HRS
UV LAMP: XX HRS
BLOWER: XX HRS - XX CYC
COOLING
HEATING
FREE COOLING: XX HRS - XX CYC
FANS
EXHAUST
HUMIDITROL: XX HRS - XX CYC
ALARMS
STATUS
LAST USB REPORT
READ INSTALL RPT
CLEAR HISTORY
TSTAT SMK:OFF/ON
RH:XX%
BRPM:XX
IE:XX MA
OAT:XXºF
OE:XX MA
RAT:XXºF
GLO:OFF/ON
DAT:XXºF
DI2:OFF/ON
ZAT:XXºF
DI3:OFF/ON
IAQ:XX PPM DI4:OFF/ON
LCONN ADDRESS
BACNET
LonTalk
READ M2 SOFTWARE VERSION
READ DB SOFTWARE VERSION
READ FACTORY RPT
CATALOG NO.
MODEL NO.
SERIAL NO.
OCCUPIED/UNOCCUPIED
SETPOINTS HH CC F
APP MODE 255 255
COMM TYPE
COMM TIMER
#CURR ALRMS N: A1, A2, ... AN
BLOWER
DAMPER STATUS
DAMPER POS
UNIT NO.
DATE/TIME
UNITS F/C
COOLING
HEATING
DAMPER
REHEAT
EXHAUST
IAQ
ALARMS
LOCAL
THERMOSTAT
LCONN
BACnet
LonTalk
MSAV
REHEAT
SMOKE MODE
GUIDED SETUP
ECTO
N/A
NEW M2
DAMPER
LANGUAGE (ENGL/SPAN/FREN)
FLOAT SW
BLOWER PROVING SW
DIRTY FILTER SW
BLOWER OVERLOAD SW
PHASE MONITOR
UV LAMP
ELECTRIC HEAT STAGES
UPDATE DISPLAY SOFTWARE