Related Manuals for Hoover HGV 7550B
Summary of Contents for Hoover HGV 7550B
- Page 1 INSTRUCTIONS FOR USE AND INSTALLATION ISTRUZIONI D’USO E DI INSTALLAZIONE MANUAL DE UTILIZAÇÃO E DE INSTALAÇÃO...
-
Page 2: Table Of Contents
All these characteristics are given for information with a constant concern for improving production quality, the manufacturer may make modification to the appliance to incorporate technical improvements. The hobs are in conformity with directives 89/336/CEE, 73/23/CEE and 90/396/CEE. CONTENTS Unpacking the appliance ..............2 Recommendations ................ -
Page 3: Hob Features
(located under the lower casing of the hob) . Rating plate • All accessible parts of the hob will become hot while in operation. Always keep children away from it. • The hob should be given a quick clean after each use, to avoid the accumulation of spillages and grease. -
Page 4: Installation
INSTALLATION Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in accordance with the technical regulations in force. In the event that this advice is ignored and the installation is carried out by an unqualified person, the society declines all responsibility for any technical failure of the product whether or not it results in damage to goods or injury to individuals. -
Page 5: Modification Of The Factory Gas Setting : * Fitting Of The Correct Jets
INSTALLATION: «GAS CONNECTION» ¤ ¤ ¤ ¤ = Factory setting: Natural gas = G20-20 mbar / G25-25 mbar = Gas setting possible according to installation Butane gas G30-29 mbar or Propane gas G 31-37 mbar CHANGING THE GAS TYPE : the calorific power output and gas pressure will vary according to the gas supply. -
Page 6: Fitting The Hob
INSTALLATION : «BUILDING-IN» Both the worktop where the hob will be fitted and any adjacent kitchen furniture must be made from heat resistant material and fixed with heat resistant adhesive. If, when installing the hob, the lower hob face is adjacent to an area normally accessible when handling or cleaning, fit a heatproof partition 1 cm below the base of the hob with a 10X10 cm opening at the rear right-hand corner, to avoid any risk of scorching or damage. -
Page 7: Gas Connection
INSTALLATION: «GAS CONNECTION» The hob can be built-in ; it is in class 3 (in compliance with gas regulations EN 30.1.1) ; adjoining furniture should not be higher than the level of the hob. This appliance is not connected to an evacuation device for the products of combustion. It must be installed and connected in compliance with the norms in force in the country of installation. -
Page 8: Electrical Connection
INSTALLATION: «ELECTRICAL CONNECTION» The mains electricity supply connected to the appliance should comply with the norms in force in the country of installation. Connection to the mains electricity supply should be through a socket with an earth terminal, or through an intermediary switching device with a gap between contacts of at least 3 mm. -
Page 9: After Final Installation Of The Hob (If Modification Of The Gas Setting) : Adjusting Of The Lower Flame On The Gas Burners
INSTALLATION: «REGULATING THE FLAME» • SETTING THE IDLE FLAME If you have changed the type of gas, it is important to verify the flame stability at the minimum regulation. «Gaining access to the by-pass screw» To gain access to hob burner by-pass screws, remove the knobs from the control panel. By-pass screw of the hob burner Never loosen the others screws ! -
Page 10: Using The Appliance The Different Gas Burners
THE GAS BURNER THE ULTRA-RAPID BURNER or "4 RINGS" BURNER, power rating 3,5 kW : use this burner for bringing to boil, for cooking large quantities, and generally for all foods requiring rapid cooking. THE FAST BURNER, power rating 2,5 kW : use the large burner for all foods requiring rapid cooking. -
Page 11: Igniting And Setting The Burner
Each burner is fitted with automatic ignition. The ignition can be made with one hand, while you have the pan in the other hand. USE : • Turn on the gas tap, • A symbol next to each control knob indicates which burner is lit. -
Page 12: The Hot Plate - Some Tips
THE HOT PLATE THE SPEED PROTECTED HOT PLATE - 1500 W. This is a cast-iron hot plate, controlled by a 7 position switch. An internal thermostat cuts off part of the power supply if overheating occurs. (if, for example, a hot plate is working without a pan on it). BEFORE USING THE ELECTRICAL HOT PLATE : •... - Page 13 Cooking with the electrical hot plate To get the best results from your appliance it is important to observe the following : • Use thick, flat-based cooking vessel : a completely flat base prevents overheating to certain parts which causes food to stick. Thick metal allows for good heat distribution.
-
Page 14: General Maintenance
CLEANING AND MAINTENANCE Before cleaning or removing the hob, it is imperative to : • disconnect the hob from the mains supply, • let all parts of the hob cool down. Never use harsh abrasives, scouring pads or sharp objects to clean the hob. Do not use a sponge that it is excessively wet. - Page 15 THE GAS BURNERS Burner cap Pan support Burner head • Burner caps and pan supports : the pan support is made of enamelled cast-iron and the burner cap is made of enamelled steel, for a maximal protection and an easy cleaning. They are simply placed.