Bosch GWS 8-100 ZProfessional Original Instructions Manual page 9

OBJ_BUCH-1556-004.book Page 9 Monday, February 8, 2016 8:05 AM
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Spindle lock button
2 On/Off switch
3 Lock-off button for On/Off switch
Technical Data
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for EC countries:
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 89 dB(A); Sound power level
100 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Surface grinding: a = 4.5 m/s , K=1.5 m/s
h
2
Disk sanding: a = 4.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
Bosch Power Tools
4 Combination spanner for M 10 grinder spindle
5 Auxiliary handle (insulated gripping surface)
6 Grinder spindle
7 Protection guard for grinding
8 Locking screw for protection guard
9 Mounting flange
10 Grinding wheel*
11 Clamping nut
12 Carbide grinding head*
13 Protection guard for cutting*
14 Cutting disc*
15 Hand guard*
16 Rubber sanding plate*
17 Sanding sheet*
18 Round nut*
19 Cup brush*
20 Cutting guide with dust extraction protection guard *
21 Diamond cutting disc*
22 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
W
W
-1
min
mm
mm
kg
kg
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
2
,
Identify additional safety measures to protect the operator
2
.
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
English | 9
GWS 8-100 Z GWS 8-115 Z
3 601 H31 5.. 3 601 H31 5..
800
500
11000
100
M 10
17
2.0
1.9
/II
1 609 92A 28E | (8.2.16)
800
500
11000
115
M 14
17
2.0
1.9
/II