Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Gateway
  5. T3
  6. Installation manual

Cisco T3 Installation Manual

Universal gateway card t3 dial feature card as5400;as5350
Hide thumbs Also See for T3:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
Cisco AS5350 and AS5400 Universal Gateway Card Installation Guide
T3 Dial Feature Card

Table Of Contents

Overview
T3 Dial Feature Card
This chapter describes the T3 dial feature card and includes the following sections:
• Overview
• Online Installation and Removal (OIR) of the T3 DFC
• Getting Help
• Where to Go Next
Overview
The T3 DFC provides physical line termination for a channelized T3 ingress trunk line. It uses an
onboard multiplexer to multiplex 28 channelized T1 lines into a single channelized T3 line. (See
Figure
4-1.)
The T3 DFC provides physical line termination for up to 672 DS0 channels and uses onboard
HDLC controllers to terminate digital (ISDN) calls.
You can use the bantam jacks on the DFC to monitor a T1 line or test any one of the individual
T1 circuits in drop and insert mode.

Advertisement

loading

Related Manuals for Cisco T3

Summary of Contents for Cisco T3

  • Page 1: Table Of Contents

    • Getting Help • Where to Go Next Overview The T3 DFC provides physical line termination for a channelized T3 ingress trunk line. It uses an onboard multiplexer to multiplex 28 channelized T1 lines into a single channelized T3 line. (See Figure 4-1.)

  • Page 2: T3 Dial Feature Card

    You can install a T3 DFC in any DFC slot of the universal gateway chassis. Note The Cisco AS5350 and Cisco AS5400 support only one type of WAN DFC at a time. Refer to "Troubleshooting," for more information. Figure 4-1 T3 Dial Feature Card...

  • Page 3: Removing The T3 Dfc

    Removing the T3 DFC To remove the T3 DFC, follow these steps: Note Following these steps are examples of the output from each command. Step 1 Determine which slot the DFC is in (See Figure 4-2 Figure 4-3.) by entering the...
  • Page 4 Router# show busyout slot-number Step 4 You may use the clear port command to immediately disable active calls on the universal port card. Use the show controller command to show the universal port card associated with the T1 or E1 DFC. Router# show controller t1/e1 slot-number/control-number timeslot timeslot- number Router# clear port slot-number/port number...
  • Page 5 Note OIR of the T3 DFC is similar to that of the T1 or E1 DFC. To see an example of the output during online insertion and removal of an E1 DFC refer to Chapter 3, "T1 and E1 Dial Feature Cards"...

  • Page 6: Installing The T3 Dfc

    Figure 4-6 Remove the DFC from the Cisco AS5350 Figure 4-7 Remove the DFC from the Cisco AS5400 Step 10 After you remove the DFC from the chassis, set it aside on an ESD-preventive mat. Step 11 If a DFC slot on the carrier card is to remain empty, install a blank cover over the open DFC slot to ensure proper airflow inside the chassis.
  • Page 7 If you replace the existing DFC with a new DFC of a different type, you will have to reconfigure the system. For configuration details, refer to the Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide.

  • Page 8: Getting Help

    Figure 4-12 Tighten the Captive Screws on the Cisco AS5400 Step 5 Check the card LEDs to verify that the card is working properly. For information about dial feature card LEDs, refer to "Troubleshooting" Getting Help For information about technical support, onsite service, and exchange and repair services, refer to the "Obtaining Technical Assistance"...
  • Page 9 • "Cabling Specifications."...