AMX NXA-ENET8-2POE Instruction Manual page 69

Access Control List Conf iguration Parameters
ACE CONFIGURATION (Cont.)
• ARP (Cont.) IP/Ethernet Length
• IPv4:
NXA-ENET8-2POE - Instruction Manual
Specifies whether frames can be matched according to their ARP/RARP hardware address
length (HLN) and protocol address length (PLN) settings. (Options: Any - any value is allowed,
0 - ARP/RARP frames where the HLN is equal to Ethernet (0x06) and the (PLN) is equal to IPv4
(0x04) must not match this entry, 1 - ARP/RARP frames where the HLN is equal to Ethernet
(0x06) and the (PLN) is equal to IPv4 (0x04) must match this entry; Default: Any)
IP Specifies whether frames can be matched according to their ARP/RARP hardware address
space (HRD) settings. (Options: Any - any value is allowed, 0 - ARP/RARP frames where the
HRD is equal to Ethernet (1) must not match this entry, 1 - ARP/RARP frames where the HRD is
equal to Ethernet (1) must match this entry; Default: Any)
Ethernet Specifies whether frames can be matched according to their ARP/RARP protocol address
space (PRO) settings. (Options: Any - any value is allowed, 0 - ARP/RARP frames where the
PRO is equal to IP (0x800) must not match this entry, 1 - ARP/RARP frames where the PRO is
equal to IP (0x800) must match this entry; Default: Any)
MAC Parameters
• DMAC Filter The type of destination MAC address. (Options: Any, MC - multicast, BC - broadcast, UC -
unicast; Default: Any)
IP Parameters
• IP Protocol Filter Specifies the IP protocol to filter for this rule. (Options: Any, ICMP, UDP, TCP, Other; Default:
Any)
The following additional fields are displayed when these protocol filters are selected.
ICMP Parameters
• ICMP Type Filter Specifies the type of ICMP packet to filter for this rule. (Options: Any, Specific: 0-255; Default:
Any)
• ICMP Code Filter Specifies the ICMP code of an ICMP packet to filter for this rule. (Options: Any, Specific
(0-255); Default: Any)
UDP Parameters
• Source Port Filter Specifies the UDP source filter for this rule. (Options: Any, Specific (0-65535), Range
(0-65535); Default: Any)
• Dest. Port Filter Specifies the UDP destination filter for this rule. (Options: Any, Specific (0-65535), Range
(0-65535); Default: Any)
TCP Parameters
• Source Port Filter Specifies the TCP source filter for this rule. (Options: Any, Specific (0-65535), Range
(0-65535); Default: Any)
• Dest. Port Filter Specifies the TCP destination filter for this rule. (Options: Any, Specific (0-65535), Range
(0-65535); Default: Any)
• TCP FIN Specifies the TCP No more data from sender (FIN) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the FIN field is set must not match
this entry, 1 - TCP frames where the FIN field is set must match this entry; Default: Any)
• TCP SYN Specifies the TCP Synchronize sequence numbers (SYN) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the SYN field is set must not match
this entry, 1 - TCP frames where the SYN field is set must match this entry; Default: Any)
• TCP RST Specifies the TCP Reset the connection (RST) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the RST field is set must not match
this entry, 1 - TCP frames where the RST field is set must match this entry; Default: Any)
• TCP PSH Specifies the TCP Push Function (PSH) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the PSH field is set must not match
this entry, 1 - TCP frames where the PSH field is set must match this entry; Default: Any)
• TCP ACK Specifies the TCP Acknowledgment f ield signif icant (ACK) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the ACK field is set must not match
this entry, 1 - TCP frames where the ACK field is set must match this entry; Default: Any)
• TCP URG Specifies the TCP Urgent Pointer f ield signif icant (URG) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the URG field is set must not match
this entry, 1 - TCP frames where the URG field is set must match this entry; Default: Any)
• IP TTL Specifies the time-to-Live settings for this rule.
(Options: Any - any value is allowed, Non-zero - IPv4 frames with a TTL field greater than zero
must match this entry, Zero - IPv4 frames with a TTL field greater than zero must not match
this entry; Default: Any)
Configuring the NXA-ENET8-2POE
67