AMX NXA-ENET8-2POE Instruction Manual page 119

QoS Control List Conf iguration parameters
Key Parameters (Cont.)
• DEI
• SMAC
• DMAC Type
• Frame Type
Action Parameters
• Action
1. Click Conf iguration, QoS, QoS Control List.
2. Click the button to add a new QCE, or use the other QCE modification buttons to specify the editing action (i.e., edit, delete, or
moving the relative position of entry in the list).
3. When editing an entry on the QCE Configuration page, specify the relevant criteria to be matched, and the response to a
match.
4. Click Save.
NXA-ENET8-2POE - Instruction Manual
Drop Eligible Indicator. (Options: 0, 1 or Any)
The OUI field of the source MAC address. Enter the first three octets (bytes) of the MAC address, or Any.
The type of destination MAC address. (Options: Any, BC (Broadcast), MC (Multicast), UC (Unicast)
The supported types are listed below:
Any - Allow all types of frames.
Ethernet - This option can only be used to filter Ethernet II formatted packets. (Options: Any, Specific. 600-ffff
hex; Default: ffff)
Note that 800 (IPv4) and 86DD (IPv6) are excluded.
A detailed listing of Ethernet protocol types can be found in RFC 1060. A few of the more common types
include 0800 (IP), 0806 (ARP), 8137 (IPX).
LLC - Link Logical Control includes the following settings:
SSAP Address - Source Service Access Point address. (Options: Any, Specific (0x00-0xff); Default: 0xff)
DSAP Address - Destination Service Access Point address. (Options: Any, Specific (0x00-0xff); Default: 0xff)
Control - Control field may contain command, response, or sequence information depending on whether the
LLC frame type is Unnumbered, Supervisory, or Information. (Options: Any, Specific (0x00-0xff); Default:
0xff)
SNAP - SubNetwork Access Protocol can be distinguished by an OUI and a Protocol ID. (Options for PID: Any,
Specific (0x00-0xffff); Default: Any)
If the OUI is hexadecimal 000000, the protocol ID is the Ethernet type (EtherType) field value for the
protocol running on top of SNAP.
If the OUI is that of a particular organization, the protocol ID is a value assigned by that organization to the
protocol running on top of SNAP.
In other words, if value of the OUI field is 00-00-00, then value of the PID will be EtherType (0x0600-0xffff),
and if value of the OUI is other than 00-00-00, then valid value of the PID will be any value from 0x0000 to
0xffff.
IPv4 - IPv4 frame type includes the following settings:
Protocol - IP protocol number. (Options: Any, UDP, TCP, or Other (0-255))
Source IP - Source IP address. (Options: Any, Specific) To configure a specific source IP address, enter both
the address and mask format. The address and mask must be in the format x.y.z.w where x, y, z, and w are
decimal numbers between 0 and 255. When the mask is converted to a 32-bit binary string and read from left
to right, all bits following the first zero must also be zero
IP Fragment - Indicates whether or not fragmented packets are accepted. (Options: Any, Yes, No; Default:
Any) Datagrams may be fragmented to ensure they can pass through a network device which uses a
maximum transfer unit smaller than the original packet's size.
DSCP - Diffserv Code Point value. (Options: Any, specific value of 0-63, BE, CS1-CS7, EF or AF11-AF43, or
Range; Default: Any)
IPv6 - IPv6 frame type includes the same settings as those used for IPv4, except for the Source IP. When
configuring a specific IPv6 source address, enter the least significant 32 bits (a.b.c.d) using the same type of
mask as that used for an IPv4 address.
Sport - Source TCP/UDP port. (Any, Specific/Range: 0-65535)
Dport - Destination TCP/UDP port. (Any, Specific/Range: 0-65535)
Indicates the classification action taken on ingress frame if the configured parameters are matched in the frame's
content. If a frame matches the QCE, the following actions will be taken:
Class (Classified QoS Class) - If a frame matches the QCE, it will be put in the queue corresponding to the
specified QoS class, or placed in a queue based on basic classification rules. (Options: 0-7, Default (use basic
classification); Default setting: 0)
DPL - The drop precedence level will be set to the specified value or left unchanged. (Options: 0-1, Default;
Default setting: Default)
DSCP - The DSCP value will be set to the specified value or left unchanged. (Options: 0-63, BE, CS1-CS7, Default
(not changed); Default setting: Default)
Configuring the NXA-ENET8-2POE
117