Canon iR1019 Service Manual page 14

Contents
15.4.1 Menu Switch Composition..................................................................................................................................15- 12
15.4.2 <No.005 NL equalizer> ......................................................................................................................................15- 13
15.4.3 <No.006 telephone line monitor> .......................................................................................................................15- 13
15.4.4 <No.007 ATT transmission level> ......................................................................................................................15- 13
15.4.5 <No.008 V.34 modulation speed upper limit> ....................................................................................................15- 13
15.4.6 <No.009 V.34 data speed upper limit>...............................................................................................................15- 13
15.4.7 <No.010 Frequency of the pseudo CI signal>....................................................................................................15- 13
15.5 Setting of Numeric Parameter (NUMERIC Param.).............................................................................. 15- 13
15.5.1 Numerical Parameter Composition ....................................................................................................................15- 13
15.5.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)>
15- 14
15.5.3 <005: NCC pause length (pre-ID code)> ...........................................................................................................15- 14
15.5.4 <006: NCC pause length (post-ID code)>..........................................................................................................15- 14
15.5.5 <010: line connection identification length> .......................................................................................................15- 14
15.5.6 <011: T.30 T1 timer (for reception)> ..................................................................................................................15- 14
15.5.7 <013: T.30 EOL timer>.......................................................................................................................................15- 14
15.5.8 <015: hooking detection time> ...........................................................................................................................15- 14
15.5.9 <016: time length to first response at time of fax/tel switchover> ......................................................................15- 14
15.5.10 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:
pseudo RBT signal pattern OFF time length (long)> ...............................................................................................15- 14
15.5.11 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)> ...................................................................................................15- 15
15.5.12 <023: CNG detention level for fax/tel switchover> ...........................................................................................15- 15
15.5.13 <024: pseudo RBT transmission level at time of fax/tel switchover> ...............................................................15- 15
15.5.14 <025: Answering machine connection function signal detection time> ............................................................15- 15
15.5.15 <027: V.21 low-speed flag preamble identification length>..............................................................................15- 15
15.5.16 <056 - 061: Count type select > .......................................................................................................................15- 15
15.6 Setting of Scanner Functions (SCANNER)........................................................................................... 15- 18
15.6.1 Numeric Parameter Functional configuration.....................................................................................................15- 18
15.6.2 <024:CIS scan position during ADF scanning> .................................................................................................15- 19
15.6.3 <026:Distance from the standby position of CIS to the shading start point> .....................................................15- 19
15.6.4 <031: Vertical scan start position adjustment> ..................................................................................................15- 19
15.6.5 <032: Horizontal scan start position adjustment> ..............................................................................................15- 19
15.6.6 <033: Vertical scan magnification correction> ...................................................................................................15- 19
15.6.7 <034: Horizontal scan magnification correction> ...............................................................................................15- 19
15.6.8 <035: - 036:Reader motor speed change> ........................................................................................................15- 19
15.6.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)>........................15- 19
15.6.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)>..................15- 19
15.6.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)> ......................................................15- 20
15.6.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)> ................................................15- 20
15.6.13 <045: Horizontal scan end position correction (fine:scanning on ADF)> .........................................................15- 20
15.6.14 <046: Horizontal scan end position correction (standard:scanning on ADF)> .................................................15- 20
15.6.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)> .......................15- 20
15.6.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)>...................15- 20
15.6.17 <054: Pickup motor speed correction (when the ADF is used) > .....................................................................15- 20
15.6.18 <193: ADF special standard-sized paper: LGL misidentification-ready> .........................................................15- 20
15.6.19 <194: ADF special standard-sized paper: LTR misidentification-ready> .........................................................15- 20
15.6.20 <195: ADF special standard-sized paper: LTR_R misidentification-ready>.....................................................15- 20
15.6.21 <213: XYZ correction value (X) of standard white plate> (equipped with SEND functions).............................15- 21
15.6.22 <214: XYZ correction value (Y) of standard white plate> (equipped with SEND functions).............................15- 21
15.6.23 <215: XYZ correction value (Z) of standard white plate> (equipped with SEND functions) .............................15- 21
15.7 Setting of Printer Functions (PRINTER) ............................................................................................... 15- 21
15.7.1 Service Soft Switch Settings (PRINTER) ...........................................................................................................15- 21
15.7.1.1 SSSW-SW05...................................................................................................................................................................... 15- 21
15.7.1.2 SSSW-SW14...................................................................................................................................................................... 15- 22
15.7.1.3 SSSW-SW15...................................................................................................................................................................... 15- 22
fineline6