Advertisement
la
use
d adapter pk..lfj
E&ause of po&nt~a/safety hazards
undercertain conditions, we strongly
recommend againstuse of an adapter
plug. However, if you still eiectto use
artadapter,where local codes permit,
aTEMPORARYCONNECTION may
be madeto a properly grounded
two-prong wail receptacle by use of
a UL listed adapter (Fig. 2) available
at most local hardware stores,
TEMPORARY MEIIKNI
(ADAPTER P LUGS NOT
PERMITTED I N CANADA)
n
/
ALIGN LARGE
Q
'\
PRONGS/SLOTS ~
-..
-.
&l&jjyJ7E~
u
@
GROIJNII A ND
~
FIRMCONNECTION
Fig. 2
~ ]
BEFORE USE
TheIargerslot in the adapter must be
aligned with the Iargerslot in the wall
receptacle to provide proper polarity
in the connection of the power cord.
CAUTK3N: Attaching adapter
ground terminal to wall receptacle
cover screw does not ground the
appliance unless cover screw is
metal, and not insulated, and wall
receptacle is grounded through
house wiring. Customer should
17ave the circuit checked by a qual-
ified electrician to make sure the
receptacle is properly grounded.
When disconnecting the power
cord from the adapter, always hold
the adapter with one hand. If this
is not done, the adapter ground
terminal is very likely to break
with repeated use.
Should the adapter ground
terminal break, DO NOT USE the
appliance until a proper ground
has again been established.
Because of potential safety hazards
under certain conditions, we strongly
recommend against the use of an
extension cord. However,if you still
elect to use an extension cord, it is
absolutely necessarythat it be a UL
listed 3-wire grouriding type appli-
ance extension cord and that the
current carrying rating of the cord be
15amperes minimum. Such exten-
sion cords are obtainable through
your Iota/ service organization.
The rehkywator
slm.dd
always
be p!ug'jged
i ntoits
own
hdivichali ekedrical
cNJtkt——
(115volt, 60 Hertz, or 100 volt,
50 Hertz, single phase AC).
This is recommended for best
performance and to prevent over-
loading house wiring circuits,
which could cause a possible fire
hazard from overheating wires.
LCm3ticm
Do not installrefrigeratorwhere
temperaturewill go below 60°F.
because it will not run often enough
to maintain proper temperatures.
Do installit on a floorstrongenough
to supporta fullyloadedrefrigerator.
Also see Energy-Saving Tips
regarding location.
Mow 5/8" at each sick and 1" over
the top for ease of installationand
proper air circulation.
consider providing water supply to
refrigerator location. It will simplify
connection of optional automatic
icemaker should you wish to install
one at a later date.
Adjustabk rokm, which enable
you to move your refrigerator away
from the wall for cleaning, are
located behind the base griile.
These rollers should be set so that
the refrigerator is firmly positioned
on the floor and the front is raised
just enough that the doors close
easily when opened about halfway.
[
I
Toadjustrollers,remove the base
grille by grasping it at the bottom
and pulling it cwt.
Turnrolleradjustingscrewsclock-
wise to raise refrigerator, counter-
clockwise to lower it. Useadjustable
wrench (3/8" hex head bolt) or pliers.
When adjusting front rollers for
proper door closure, it is recom-
mended that the bottom front edge
of the cabinet be approximately
5/8 inch from the floor.
To replace base grille, align prongs
on back of grille with clamps in
cabinet and push forward until
grille snaps into place.
Advertisement
