And if there are changes, Tenda is not responsible for informing in advance. If you want to know more about our products information, please visit our website at www.tenda.cn...
TEI402M Multifunction Broad Band Router Chapter 1 Introduction 1.1 Product Feature One 10M/100M auto negotiation WAN port, connectible to xDSL/Cable Modem or Ethernet Four 10M/100M auto negotiation LAN ports Compliant with IEEE802.3 Ethernet Standard IEEE802.3u Fast Ethernet Standard Support TCP/IP, PPPoE, PPTP, DHCP, ICMP, NAT, SNTP protocol Prevent D.O.S Network attack...
TEI402M Multifunction Broad Band Router Chapter 2 Hardware Setup 2.1 Rear Panel Power: Special Power Adapter. WAN: WAN PORT(RJ-45) Connect to Xdsl/Cable Modem or Ethernet. LAN Port: 4 RJ-45 ports Computer and HUB/Switch connect Ethernet through these ports. Notice: 1. please use the special power with this router otherwise it will be damaged.
TEI402M Multifunction Broad Band Router 2.3 Hardware Install Process 2.3.1.Establish LAN Connection Connect the port of router with HUB or switch by a line. You also can connect the computer LAN card directly. 2.3.2 Establish WAN Connection Connect the WAN port of router with xDSL/Cable Modem by a line.
TEI402M Multifunction Broad Band Router Chapter 3 Router Setting 3.1 Setup Right Network The default IP address of this router is 192.168.0.1.The default subnet mask is255.255.255.0.All these parameters can be amended if needed but in this use manual we will illuminate according the fault parameters.
Page 8
TEI402M Multifunction Broad Band Router If the user name and password is correct, a screen of administrator pattern will appear .The default user name and password are all admin. Click “Next” or Wizard of left manual to select how to access internet.(This router can access internet in 3 ways).
Page 9
TEI402M Multifunction Broad Band Router Username & Password: Enter Account and password provided by ISP. If you don’t know them please refer to ISP. 2. If you can access internet with dynamic IP address .Namely, you can obtain IP address automatically from your ISP .You needn’t...
Page 10
TEI402M Multifunction Broad Band Router Subnet Mask: The router subnet mask to WAN (default setting:255.255.255.0). Gateway: Fill in the gateway provide by your ISP, If you don’t know them well please refer to your ISP . Primary DNS: Fill in the DNS server provide by your ISP, If you don’t know them well please refer to your ISP.
Page 11
TEI402M Multifunction Broad Band Router IP address: 10.0.0.138 Connection ID: (Connection name. Can be left empty) MTU: 1400 MPPE: un-check ‘enabled’ checkbox. WAN Interface IP: Static IP IP address: 10.0.0.150 Subnet mask: 255.255.255.0 Gateway: 10.0.0.138 (your modem’s ip) After filling in all the above parameters please come to Configuration Wizard as follows: Now, please click Save to save fast setting.
TEI402M Multifunction Broad Band Router and clone MAC address, please click Advanced Config. If you need setup DHCP service, please click DHCP Server . If you need startup DMZ, UpnP and Virtual Service, please click Virtual Service. If you need setup dynamic DNS, modify User information, restart router, upgrade software, backup currently setting, please click System Tool.
TEI402M Multifunction Broad Band Router requirements. Notice: If you change the IP address, you must use the new IP address to log on the router to manage the WEB interface and all default gateway of computers of the LAN must setup as the new IP address.
TEI402M Multifunction Broad Band Router management computer to that of Wan port(you also can modify it by manual). 3.3.3.4 DNS Primary DNS: Fill in the DNS server provide by your ISP, If you don’t know them well please refer to your ISP.
TEI402M Multifunction Broad Band Router 3.3.4.2 DHCP Client List DHCP Client List show the assigned IP address, client MAC address and HOST name. 3.3.5 Virtual Service In the Virtual Service menu, there are five submenu: Virtual server , DMZ Host, UpnP setting, and UpnP mapping Table.
TEI402M Multifunction Broad Band Router 3.3.5.2 DMZ Host In some special situation, a computer need to exposure entirely to WAN in order to implement intercommunication. You need appoint the computer as DMZ host. 3.3.5.3 UPnP Mapping Table This page shows the status of UPnP equipments.
TEI402M Multifunction Broad Band Router Port: The executive web management port number. IP Address: The IP address of the computer in WAN that remote web manages. Notes: 1. The default web management port of the router is 80, if the web management port is changed (e.g..8080), the user...
TEI402M Multifunction Broad Band Router same network segment. 2. If the target IP address is a IP address of host, the subnet mask must be 255.255.255.255. 3. The target IP address must match the subnet mask if it is in IP network segment.