Table of Contents
Advertisement
(3)
Sv/itchintj
to the
EDIT mode and Entering
Data
(Fig, 22)
{c)
Enter the EDIT mode using
the
EDIT/COMPARE
switch.
This makes
it
possible
to
alter
the data in the EDIT
BUFFER.
(d)
The VOICE MEMORY channel will
automatically
be
selected/ and the
target EDIT voice indicator will flash.
*
If
the
KEY ASSIGN MODE switch is set to
DU/iLr
sound will
be
output from both
channels A and
B,
In
order to monitor
only the target EDIT voice, set the
BALANCE slide control
all the
way
to
the
corresponding channel.
(e)
The LED and
LCD displays display
the
data
for the
target voice,
*
The
leftmost operator select switch
determines which individual operator
data
is
displayed.
*
The LED display displays the data
for
the
parameter shown
belov7 it.
*
The LCD display shows the data
of
.
parameter selected
by the
PERFORMANCE
f
MEMORY/FUNCTION
switch.
(f)
Select
the
parameter
to be
edited
using the row
of
voice parameter
switches below the LED display,
or
the
PERFORI-iAlXE
liEnORY/FUNCTION switches.
*
The voice parameter switches include
most
of the FK
tone generator and
operator functions that
are
essential
for
voice creation.
-*p.27
*
The
PERFORM/J^ICE
MEMORY/FUNCTION switches
include LFO modulation-related effects
that affect
all
operators
simultaneoulsy.
~*p.27
*
Envelope generator voice parameter
Rl
is
automatically selected.
Simply press
the
appropriate switch
to
select
another parameter,
(g)
Set the desired data value using the
DATA ENTRY section.
*
Data can also
be set by
continuously
pressing
the
selected (flashing)
PARAMETER
switch.
*
Use the COMPARE switch to compare the
sound
of
the
edited data
v;ith
the
sound
of
the
original
data.
-»a^
(h)
To set the
parameters
for
each
operator, use the OPERATOR SELECT
switches
to
select the operator
to be
worked
on.
^p.21
*
Using the OPERATOR ON/OFF switches
it is
possible
to
concentrate
on
a
single
operator, permitting extremely fine
sound control,
-^p.22
(i)
After editing on one channel
has been
completed, switch over
to the other
channel and perform
any
necessary
editing on that channel.
Either
channel can be selected
by
pressing
a
bank or voice switch
of
the channel you
wish
to
select.
*
Also set
the balance slider all the
way
to the
appropriate channel.
(4)
Storing Edit
Data
In
order
to
store edit
data,
a
store
operation must
be
performed.
Two
processes
are possible:
(1)
Storing data without
changing
the
memory position, and
(II),
storing data in
a
new
VOICE MEMORY
or
PERFORMANCE MEMORY position.
*
Each time power
to the DXl is
turned
on,
the internal memory protect system is
activated in order
to
prevent
accidental memory erasure.
This
function must
be
turned
off in
order
to
perform
a
store operation.
*
VJhen a
store operation
is
performed,
data
originally
in the memory to
which
the store is
performed will
be
erased.
Data which needs
to be
saved should
therefore
be
stored in an external RAM
cartridge,
-/»4ff
*
In
order
to
store edit data
on
an
external cartridge,
a
cartridge
formatted
for
VOICE MEMORY storage must
be used.
A catridge formtted for
PERFORMANCE MEMORY cannot
be used.
JFig, 22.
Switching to Edit Mode
and
Entering Data
(e)LED
display
1
SEtECI
1
1
1
L(h)Operator
select.
HH
:a9SM99W9gm
0\
M
nSl
JM
(g)
n
Set balance slider to full
to
monitor
the
individual
voice in dual mode.
S
a-B-
(d)Voice
selected
for
editing flashes.
(i)Edit
another channel
voice
by
pressing
the
voice
or
bank switch to change channel.
Parameter switch
B B B B
^
BBBBB SbB
t
(CJ
EL)
IT
nODE
:::Lru:::::
19
Advertisement
Table of Contents
