MTD 140 Operator's Manual
Single-stage snow thrower
Hide thumbs
Also See for 140:
- Operator's manual (32 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (5 pages)
Table of Contents
Advertisement
O
PERATOR'S
Read safety rules and instructions carefully before operating equipment.
IMPORTANT:
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered,
brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state
laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above
is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal
lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department,
PRINTED IN U.S.A.
ECO No.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
M
ANUAL
Single-Stage
Snow Thrower
Models
140
150
E150
E162
E172
. 770-10000F.fm
FORM NO
(10/2003)
Advertisement
Table of Contents
Related Manuals for MTD 140
Summary of Contents for MTD 140
-
Page 1: Snow Thrower
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 PRINTED IN U.S.A. -
Page 2: Table Of Contents
A sample model plate is explained below. For future reference, please copy the model number and the serial number of the equipment in the space below. Copy the model number here: MTD LLC Copy the serial number here: P. O. BOX 361131... -
Page 3: Important Safe Operation Practices
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning. -
Page 4: Maintenance And Storage
Maintenance And Storage Muffler and engine become hot and can cause a burn. Do not touch. Never tamper with safety devices. Check their proper Exercise extreme caution when operating on or crossing operation regularly. gravel surfaces. Stay alert for hidden hazards or traffic. Disengage all clutch levers and stop engine. -
Page 5: Assembling Your Snow Thrower
SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: This Operator’s Manual covers several models. Snow thrower features vary by model. Not all features discussed in this manual are applicable to all snow thrower models. Upper Handle Contents of Carton Before beginning installation, remove all parts from the carton and compare them to Figure 1. - Page 6 NOTE: The upper hole in the control handle provides for adjustment in belt and cable tension. Refer to page Eye Bolt 9 of this manual for instructions. Installing the Chute Directional Control’s Hex Nut Eye Bolt (on models so equipped) Cross Bar To install the upper crank of the chute directional Saddle Washer...
-
Page 7: Know Your Snow Thrower
SECTION 3: KNOW YOUR SNOW THROWER Discharge Chute Fuel Cap Primer Spark Plug Ignition Key Cover Starter Handle Electric Starter Choke Lever Button Control Handle (If So Equipped) Chute Directional Control Upper Handle Shave Plate Electric Starter Plug (If So Equipped) Auger Electric Starter Button This unit runs on a mixture of gasoline... -
Page 8: Operating Your Snow Thrower
Discharge Chute Shave Plate The pitch of the discharge chute controls the angle at The shave plate scrapes along the pavement as the which the snow is thrown. Loosen the wing knob on the snow thrower is propelled, allowing the snow close to side of the discharge chute before pivoting the the pavement’s surface to be discharged. -
Page 9: Making Adjustments
• After clearing snow, allow the engine to run for an Keep the ignition key in a safe place. The IMPORTANT: extra few minutes before storing to help dry any engine can not be started without it. moisture on the engine. •... -
Page 10: Maintaining Your Snow Thrower
Shave Plate • To check the adjustment of the shave plate, place the unit on a level surface. The wheels, shave plate and augers should all contact the level surface. Note that if the shave plate is adjusted too high, snow may blow under the housing. -
Page 11: Off-Season Storage
NOTE: Call 1-800-800-7310 for information regarding the price and availability of Rubber Paddle Kit 753-0613 price and availability of Shave Plate Kit 753-0451or or contact an authorized MTD Service Dealer in your contact an authorized MTD Service Dealer in your area). -
Page 12: Accessories & Kits
SECTION 9: ACCESSORIES & KITS The following accessories and kits are available for single-stage, two-stroke snow throwers. See the retailer from which you purchased your snow thrower, an authorized MTD Service Dealer or phone (800) 800-7310 for information regarding price and availability. - Page 13 NOTES...
-
Page 14: Parts List
SECTION 10: PARTS LIST... - Page 15 Models 140, 150, E150, E162 & E172 REF. PART DESCRIPTION 710-04071 Splined Carriage Screw, 5/16-18 x 1.0 710-3015 Hex Cap Screw, 1/4-20 x.75 712-3068 Hex Lock Nut, 5/16-18 731-0851A Chute Flange Keeper 731-0915C Lower Chute, 5.0 731-0921 Upper Chute, 5.0 736-0159 Washer, .349 x .879 x .063...
- Page 16 Models 140, 150, E150, E162 & E172...
- Page 17 Models 140, 150, E150, E162 & E172 REF. PART REF. PART DESCRIPTION DESCRIPTION 684-0054A Dash Assembly—Model E162 710-0352 Hex Index Washer Screw, 1/4-14 x .375 (Includes Plastic Cup for Mitten Grip) 710-0451 Carriage Bolt, 5/16-18 x .75 684-0056 Dash Assembly—Model 140 710-0642 Self-tapping Screw 1/4-20 x .75...
- Page 18 NOTES...
- Page 19 MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with MTD LLC does not extend any warranty for products respect to new merchandise purchased and used in the sold or exported outside of the United States, its United States, its possessions and territories.