Husqvarna CT151 Instruction Manual

Husqvarna CT151 Instruction Manual

Hide thumbs Also See for CT151:

Advertisement

Instruction manual
Please read these in struc tions care-
ful ly and make sure you un der stand
them before using this ma chine.
Anleitungshandbuch
Bitte lesen Sie diese Anleitungen sorg-
fältig durch und vergewissern Sie sich,
daß Sie diese verstehen, bevor Sie die
Maschine in Betrieb nehmen.
532 43 09-70 Rev. 1
CT151
Manuel d'instructions
Merci de lire trés attentivement le
manuel d'instructions. Assurez-vous
d'avoir tout compris avant d'utiliser ce
tracteur.
Manual de las instrucciones
Por favor lea cuidadosamente y com-
prenda estas intrucciones an tes
de usar esta maquina.
Manuale di istruzioni
Prima di utilizzare la macchina leggete
queste istruzioni con attenzione ed ac-
certatevi di averle comprese bene.
Instructieboekje
Lees deze instructies aandachtig en
zorg dat u ze begrijpt voordat u deze
ma chine gebruikt.

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna CT151

  • Page 1 CT151 Instruction manual Manuel d’instructions Manuale di istruzioni Please read these in struc tions care- Merci de lire trés attentivement le Prima di utilizzare la macchina leggete ful ly and make sure you un der stand manuel d'instructions. Assurez-vous queste istruzioni con attenzione ed ac- them before using this ma chine.
  • Page 2 Safety rules. Reglas de seguridad. Sicherheitsvorschriften. Norme antinfortunistiche. Règles de sécurité. Veiligheidsregels. Assembly. Montaje. Zusammenbau. Montaggio. Montage. Montering. Functional description. Descripción del funcionamiento. Funktionsbeschreibung. Funzionamento. Description du fonctionnement. Beschrijving van functies. Before starting. Antes del arranque. Maßnahmen vor dem Anlassen. Prima dell’avviamento.
  • Page 3: Safety Rules

    1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. III. OPERATION I. TRAINING •...
  • Page 4: Maintenance And Storage

    • Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless ad just ment can be made from the op er a tor’s position. • Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing.
  • Page 5 1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. I. SCHULUNG • Vor dem Gebrauch immer mit einer Sichtprüfung sicherstel- •...
  • Page 6: Wartung Und Lagerung

    • Vor dem Verlassen der Bedienungsstation: - Die Zapfwelle abstellen und alle Anbaugeräte absen- ken. - In Leerlauf schalten und die Feststellbremse einle- gen. - Den Motor abstellen und den Zündschlüssel abzie- hen. • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstel- len und das (die) Zündkerzenkabel abziehen bzw.
  • Page 7: Règles De Sécurité

    1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L ’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES.
  • Page 8: Entretien Et Entreposage

    • Débrayer les lames, arrêter le moteur, et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer. - avant de contrôler, nettoyer ou travailler sur le carter de coupe, - avant de retirer un objet coincé...
  • Page 9: Operación

    1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I.
  • Page 10: Mantenimiento Y Almacenamiento

    • Antes de dejar la posición del operador: - desenganche la fuerza motriz y baje los acceso- rios; - cambie a neutro y enganche el freno de estaciona- miento; - pare el motor y remueva la llave. • Desenganche la transmisión a los accesorios, pare el mo- tor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del con-...
  • Page 11: Norme Antinfortunistiche

    1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. •...
  • Page 12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele op- pure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e pri ma di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia;...
  • Page 13 1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING • Op machines met meerdere messen dient u eraan te denken dat het draaien van één mes andere messen kan •...
  • Page 14: Onderhoud En Opslag

    CT151 • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een ver- stopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt 15/11,2 of eraan werkt;...
  • Page 15 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit.
  • Page 16 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit.
  • Page 17 01738 GEFAHR AUGEN UNVER- ZU VERMEIDEN: SCHWEFELSÄURE ZÜGLICH MIT WASSER AUGEN SCHÜTZEN • FUNKEN KANN ERBLINDUNG AUSSPÜLEN. SOFORT EXPLOSIVE GASE ODER SCHWERE VERÄT- ÄRZTLICHE HILFE KÖNNEN ERBLINDUNG • FEUER ZUNGEN VERURSACHEN. AUFSUCHEN. UND KÖRPERVERLET- • RAUCHEN ZUNGEN VERURSAC- HEN. GEVAAR GEEN ZWAVELZUUR OGEN ONMIDDELLIJK...
  • Page 18: Steering Wheel

    2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Antes de poder utilizar el tractor, hay que montar algunas Before the tractor can be used certain parts must be as- piezas que, por razones de transporte, van empaquetadas sem bled, which for transportation reasons are enclosed in en el embalaje.
  • Page 19 Siège Retirer le bouton de réglage et la rondelle plate qui fixent le siège à l'emballage de carton, le conserver pour le montage du siège sur le tracteur. Basculer le siège vers le haut et le sortir de l'emballage de carton.
  • Page 20 HINWEIS: Prüfen, daß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist. REMARQUE: Vérifier que le câble électrique est bien connecté sur le con- tacteur de sécurité (3) placé sous l'embase du siège. NOTA: Controlar que el cable está correctamente acoplado al inter- ruptor de seguridad (3) en el soporte del asiento.
  • Page 21 Install battery NOTE: If battery is put into service after month and year 1. Battery Cover 1. Ta p a d o r d e l indicated on label, charge battery for minimum of one hour acumulador 2. Cable Positive (+) at 6-10 amps.
  • Page 22 WARNING: Positive terminal must be con nect ed first to prevent sparks from ac ci den tal grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth ca ble to -. Screw tight the cables.
  • Page 23 To install bagger com po nents to tractor 1. Support Bracket 2. Clevis Pin 10 x 17mm 3. 3/8 Lock Nut 4. 3/8 x 63,5mm Hex Bolt 5. 10,3mm (13/32") flat 1. Dis charge Chute washer 2. 3/8 Nut 6. Retainer Spring 3.
  • Page 24: Horizontal Adjustment

    To Assemble Bagger • Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto the tube. • Inside the bag, install spreader bars and retainer springs onto pins on both sides of bag as shown. •...
  • Page 25 Installation der Aufhängung der Grasfangbox des Traktors 1. Strebe 2. Fixierfeder 10x17mm 3. Kontermutter 3/8 4. Sechskantbolze 3/8 x 63,5mm 5. Flache Unterlegscheibe 10,3mm (13/32) 1. Auswurfkanal 6. Splintstift 2. Kontermutter 3/8 3. Flache unterlegscheibe • Die beiden oberen Stützwinkel mittels montieren sie die Fixierfeder 10x17mm und sichern Sie diese mit dem Splintstift.
  • Page 26: Montage Der Grasfangbox

    Montage der Grasfangbox • Entfalten Sie den Beutel, indem Sie das vordere Staub- beutelrohr ganz nach vor klappen und die untere Vinyl- bindung an das Rohr drücken. • Setzen Sie dann im Beutel die Spreizstäbe und die Rück- haltefedern in die Zapfen an beiden Seiten des Beutels wie gezeigt ein.
  • Page 27 Assemblage des composants du collecteur 1. Bras support supérieur 2. Cheville de fixation 10x17mm 3. Ecrou frein 3/8 4. Vis H 3/8 x 63,5 5. Rondelle plate diam. 10,3 mm (13/32") 1. Goulotte d'éjection 6. Epingle 2. Ecrou 3/8 3. Rondelle plate •...
  • Page 28 Pour assembler le collecteur • Déplier le sac en faisant basculer complètement vers l’avant le tube antérieur de l’ensacheuse et en poussant la bordure inférieure en vinyle sur le tube. • Dans le sac, placer les entretoises et les ressorts de retenue sur les goupilles des deux côtés du sac, de la façon illustrée.
  • Page 29 Para montar los componentes del contenedor para costales al tractor 1. Consola portadora 2. Resorte fijador 10x17mm 3. Contratuerca 3/8 4. 3/8x63,5mm arandelas planas 5. Arandela plana 10,3mm (13/32î) 1. Descarga de adaptarse 6. Clavija hendida 2. Tuercas de 3/8 3.
  • Page 30 Para montar el contenedor • Desplegar la bolsa pivoteando el tubo frontal del saco completamente hacia adelante y presionado la atadura de vinilo del fondo hacia el tubo. • En el interior de la bolsa, instalar las barras extendedoras y los resortes de retención en las clavijas en ambos lados de la bolsa como mostrado.
  • Page 31 Per montare i componenti del cesto di raccolta 1. Staffa di supporto 2. Perno di fissaggio 10x17mm 3. Dadi 3/8 1. Convogliatore di scarico 4. Bullone a testa esagonale (3/8 x 63,5mm) 2. Dadi 3/8 5. Rondella piatta 3. Rondella Piatta 6.
  • Page 32 Per montare il cesto di raccolta: • Svolgere il sacchetto ruotando completamente in avanti il tubo anteriore dell’insaccatrice e premendo la parte inferiore in vinile sul tubo. • All’interno del sacchetto, installare le barre distanziatrici e le molle di tenuta sui perni di entrambi i lati del sacchetto, come mostrato in figura.
  • Page 33 Hetmonteren van componenten van de grascontainer op de trekker 1. Stennijzer 2. Vorkbout 10x17mm 3. 3/8 borgmoer 4. 3/8 Zeskantbout 5. Vlakke sluitring 10,3 mm (13.32") 6. Sluitveer 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring • Bevestig de twee bovenste steunbeugels door de achter- •...
  • Page 34 De grascontainer monteren • Vouw de zak open door de voorste zakkenvulbuis helemaal naar voren te draaien en de onderste band van vinyl op de buis te drukken. • Installeer in de zak de spreiders en de borgveren op de pinnen aan de beide zijden van de zak, zoals op de afbeelding.
  • Page 35 1. Mango 1. Handle 2. Resorte fijador 2. Retainer Spring 3. Clavija 3. Pin 4. Tapon o tapa 4. Plug 1. Handgriff 1. Impugnatura 2. Fixierfeder 2. Coppiglia 3. Perno 3. Stift 4. Stöpsel 4. Kit Mulch ing 1. Poignée de l'insert 1.
  • Page 36 TO ADJUST GAUGE WHEELS PARA AJUSTAR LAS RUEDAS CALIBRADORAS Gauge wheels are properly adjusted when they are slightly Las ruedas calibradoras están bien ajustadas cuando se en- off the ground when mower is at the desired cutting height in cuentran un poco a distancia del terreno al mismo tiempo que operating position.
  • Page 37: Beschrijving Van Functies

    3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 03012 Positioning of controls Anordnung der Bedienungseinrichtungen 1. Light Switch. 1. Lichtschalter. 2. Gas- und Kaltstarthebel. 2. Throttle/Choke control. 3. Brems- und Kupplungspedal. 3.
  • Page 38 03012 Emplacement des commandes Comandi 1. Interrupteur de commande des phares 1. Interruttore luci. 2. Comando gas/choke. 2. Commande des gaz et starter 3. Pedale freno/frizione. 3. Pédale d'embrayage et de frein 4. Leva del cambio. 4. Levier de commande de la boîte de vitesses 5.
  • Page 39 1. Light switch 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle and choke control The accelerator control regulates the motor speed and also the speed of the blades. If the lever is in its forward position the choke function is con nect ed.
  • Page 40: Brems- Und Kupplungspedal

    3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus.
  • Page 41 4. Commande de la boîte de vitesses La boîte de vitesses possèdent des vitesses avant, une position neutre (point mort) et une marche arrière. Le pas- sage des vitesses peut s'effectuer du point mort jusqu'à la vitesse maximale sans s'arrêter sur les rapports intermédi- aires.
  • Page 42: Sollevamento/Abbassamento Del Tagliaerba

    5. Attachment clutch switch 5. Ein- und Ausschalten des Mähaggregats 5. Commande d'embrayage et de débrayage du carter de coupe 5. Acoplamiento y desacoplamiento de la uni- dad de corte 5. Leva inserimento tagliaerba. 5. Aan- en uitschakeling van de maaikast 6.
  • Page 43 ROS ON ROS ON START 7. Cerradura de encendido 7. Ignition Lock There are three different positions for the ignition key: La llave de encendido puede hallarse en tres posiciones diferentes: All electric current bro ken. Corriente eléctrica cortada ROS ON Reverse Operation System (ROS) connected ROS ON Sistema de Funcionamiento Atrás (ROS)
  • Page 44 8. Frein de stationnement Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette po si tion. 3. Relâcher la pédale d'embrayage/frein. Relâcher le levier du frein de stationnement qui restera dans sa position verrouillée (en haut).
  • Page 45 4. Before starting. 4. Maßnah men vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Filling up Reposición de combustible The en gine should be run of pure (not oil mixed) un lead ed El motor ha de funcionar con gasolina pura (sin mezcia de petrol.
  • Page 46 Oil level Nivel de aceite The combined oil refilling cap and the oil stick is ac ces si ble La tapa combinada para el llenado de aceite y para la varilla when the bonnet is lifted for wards. The oil level in the engine de nivel queda accesible después de haber levantado hacia should be checked before each run.
  • Page 47: Pressione Pneumatici

    Tire air pressure Check the tire pressure regularly. The pres sure in the front tire should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
  • Page 48 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Démarrage du moteur S’assurer que le carte de coupe est en position de transport (en position supérieure) et que le levier pour l’embrayage/dé- brayage du carte de coupe est en position de débrayage. Arranque del motor Asegúrese de que el equipo de corte está...
  • Page 49 Cold motor: Push the gas control up to end positon choke ( ). Bei kaltem Motor: Gashebel in die Endstellung choke ( ) schieben. Avec un moteur froid: pousser l'accélérateur vers le haut à la limite du starter choke ( ). Con el motor frío: Empuje el acelerador hacia arriba hasta la posición choke ( ) [estrangulación].
  • Page 50 Tourner la clef de contact en position de démarrage “START”. REMARQUE! Ne pas faire tourner le démarreur pendant plus de 5 secondes à la fois. Si le moteur ne démarre pas, attendre une dizaine de secondes avant de refaire un essai de démarrage. Ponga la llave de encendido en la posición de arranque ”START”.
  • Page 51: Betrieb

    NOTE! NOTA! The machine is equipped with a safety switch which La máquina tiene un interruptor de seguridad que corta immediately breaks the current to the en gine if the la corriente al motor si el con duc tor sale del asiento con driver leaves the seat with en gine run ning and with the el motor en marcha y con la palanca de acoplamiento/ con nec tion/dis con nec tion le ver in position “connection”.Your...
  • Page 52 Engine "ON" (Normal Operating) ROS "ON" ROS "AN" Motor "AN" (Normalbetrieb) ROS "ON" Moteur "ON" (Fonctionnement normal) ROS "ON" Motor "ON" (Funcionamiento Normal) ROS "ON" Motore "ON" (Funzionamento normale) ROS "ON" Motor "ON" (normaal functioneren) Reverse Operation System (ROS) Sécurité Marche Arrière (ROS – Reverse Op- Your tractor is equipped with a Reverse Operation System eration System) (ROS).
  • Page 53 Cutting tips Sistema per operazioni in retromarcia (ROS) Il Vostro trattore possiede un Sistema per operazioni in re- • Clear the lawn from stones and other objects which can tromarcia (ROS). Qualsiasi tentativo da parte dell’operatore be thrown away by the blades. di guidare nella direzione opposta con la frizione abbassata •...
  • Page 54 Conseils pour la tonte Consigli per il taglio dell’erba • Retirer de la pelouse, les pierres et autres objets qui • Pulire il prato da pietre e altri corpi estranei. pourraient être propulsés par les lames et devenir ainsi • Individuare ostacoli fissi.
  • Page 55 Pour vider le bac: Votre tracteur est équipé d'une alarme sonore qui vous avertit lorsque le bac est plein. Pour arrêter l'alarme, débrayer les lames. • Amener le tracteur là ou vous souhaitez le décharger. • Mettre le levier de boîte de vitesses au point mort et tirer le frein à...
  • Page 56: To Convert Mower

    To convert mower • Installieren Sie den Auswurfkanal durch die Öffnung der hin- teren Platte des Traktors auf den Adapter des Mähdecks. (Converting to mulching or rear discharging will re quire the • Fixieren Sie den Kanal, indem Sie die beiden Haken in purchase of these ac ces so ries.) die dafür vorgesehenen Bohrungen einrasten lassen.
  • Page 57 Para cambiar el ajuste de la segadora Per lo scarico a terra • Mettere il piatto nella posizione piu' alta. (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos • Togliere il cesto e il Kit Mulching siguientes) •...
  • Page 58 ATTENTION! • Ne jamais utiliser un tracteur sur des pentes excédant 15°. Les risques de renversement étant alors très importants. • Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. •...
  • Page 59: Abschalten Des Motors

    Switching off the engine Move the attachment clutch control to disengaged position. Move the throttle control between half and full speed (fast) position. Lift up the cutting unit and turn the ignition key to “STOP” position. Abschalten des Motors Stellen Sie die Steuerung der Anhängerkupplung auf aus- gekuppelt.
  • Page 60 6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstel- lung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! ADVERTENCIA! Before servicing the engine or cutting unit the fol low ing Antes de proceder a efectuar el servicio en el motor o en shall be carried out: el equipo de corte, hay que hacer lo siguiente: •...
  • Page 61 Engine hood • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt forward and lift off of tractor. • To reinstall, slide hood pivot brackets into slots in frame. • Reconnect headlight wire connector and close hood. Motorhaube •...
  • Page 62 Maintenance Mantenimiento NOTE: Periodic maintenance should be performed on a NOTA: El mantenimiento periódico ha de hacerse con regu- regular basis in order to keep your tractor in good running laridad a fin de mantener el tractor en buen estado. condition.
  • Page 63: Olie Vervangen

    PARA CAMBIAR EL ACEITE ATENCIÓN: El aceite estará caliente si el motor ha estado funcionando durante un tiempo prolongado inmediatamente antes de drenarlo. • Deslice el extensor de drenaje del aceite sobre el chasis situado por debajo del orificio de drenaje. •...
  • Page 64 SERVICE RECORD Fill in dates as you complete regular service. Every 8 Every Every . Every . Every Needed hours 25 hours 50 hours 100 hours 200 hours • Change engine oil (without oil filter) ........... • Change engine oil (with oil filter) ....................•...
  • Page 65 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les Toutes Toutes Toutes Toutes les Toutes les besoins les 8 H les 25 H les 50 H 100 H 200 H Vidange de l'huile moteur • (sans filtre à huile ..................
  • Page 66 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio. Necessità Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore • Cambio dell'olio (Senza filtro dell’olio)..........• Cambio dell'olio (Con filtro dell’olio) .................... •...
  • Page 67 Operator Presence System and Reverse Opera- tion System (ROS) Be sure operator presence and reverse operation sys tems are work ing properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully de pressed, and the attachment clutch con trol is in the dis en gaged position.
  • Page 68 Sistema de Presencia Operador y Sistema de Funcionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu tractor no funciona como descrito, hay que reparar el problema inmediatamente. • El motor no tiene que arrancar hasta que le pedal del freno no esté...
  • Page 69 Blade Care Blades IMPORTANT: The blades on your mower are not the same The blades should be sharp to achieve best cutting results. and must be installed on the correct side. It is suggested Sharpening can be carried out with a file or grinding disc. that you work on one blade at a time to ensure proper as- NOTE: It is very important that both blades are sharpened sembly of components.
  • Page 70 5-Star pattern blade w/ right hand thread ed bolt 6-Star pat tern blade w/ left hand thread ed bolt Messerbohrung mit fünfe- ckiger Aussparung, Gewin- de- Messerbohrung mit sechseckiger Aussparung, bolzen mit Rechtsgewinde. Gewindebolzen mit Linksgewinde Lame avec or i fice de fix a tion central (étoile à cinq branch es) Lame avec orifice de fix a tion central (étoile à...
  • Page 71 5-Star pattern blade w/ right hand thread ed bolt 6-Star pat tern blade w/ left hand thread ed bolt Messerbohrung mit fünfe- ckiger Aussparung, Gewin- de- Messerbohrung mit sechseckiger Aussparung, bolzen mit Rechtsgewinde. Gewindebolzen mit Linksgewinde Lame avec or i fice de fix a tion central (étoile à cinq branch es) Lame avec orifice de fix a tion central (étoile à...
  • Page 72 5 Star pattern blade 1. Hex bolt right hand 5. 5 Star Center Hole thread ed. 6. 5 Star Pattern The center of this blade has a five (5) star pattern. The bolt 2. Lock Washer that attaches this blade has normal Right Hand threads that 7.
  • Page 73 5. Orifico de centraje-es- 1. Tornillo de cabeza de Cuchilla de orificio-estrella de cinco puntas trella de cinco puntas cinco facetas, dextro- El centro de esta cuchilla se parece a una estrella de cinco giro 6. Mandril-estrella de (5) puntas. El tornillo que liga esta cuchilla es dextrogiro nor- cinco puntas 2.
  • Page 74 For best results mower blades must be kept sharp. Re place Para alcanzar resultados mejores las cuchillas de la segadora bent or damaged blades. hay que mantenerlos afilados. sustituya las cuchillas torcidos y estropeados. BLADE REMOVAL C'MO DESMONTAR LAS CUCHILLAS •...
  • Page 75 Desmontaje de la unidad de corte Trabajar desde el lado derecho de la máquina. 1. Quitar después la correa de la polea del motor (1). 2. Quitar los dos resortes posteriores (2) y golpear con un martillo los muñones de eje hasta sacarlos. 3.
  • Page 76 Remplacement de la courroie d'entraînement du carter de coupe 1. Déposer le carter de coupe (voir chapitre précédent). 2. Sortir la courroie d'entraînement des gorges de poulie en commençant par la poulie du côté gauche du carter de coupe, puis par les autres poulies. 3.
  • Page 77 01268 Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. To achieve best cutting results the cutting unit’s front edge (B) should be about 10 mm (0.375") low er than the back edge 3.
  • Page 78 00598 REGLAGE TRANSVERSAL • Relever le carter de coupe au maximum. • A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rap- “A” “A” port au sol . • La distance (A) doit être la même des deux côtés à...
  • Page 79 Cambio de correa propulsora 1. Desmontar el equipo de corte del tractor. 2. Despiezar el contacto de cable de la conexión eléctrica (1). 3. Desmontar el limitador de movimientos del acoplamiento (2). 4. Aplicar el freno de estacionamiento y tirar hacia arriba de la correa para sacarla de la rueda libre (3), de la acoplamiento (4).
  • Page 80 EINSTELLUNG DES SCHALTHEBELS DES DIF- FERENTIALGETRIEBES Das Differentialgetriebe muß sich in Leerlaufstellung be- finden, wenn der Schalthebel in der Neutral-Stellung (N) (Verschlußsperre) steht. Diese Einstellung wird bereits vom Hersteller im Werk durchgeführt. Sollte es jedoch dennoch erforderlich sein, weitere Einstellungen vorzunehmen, so muß folgendermaßen vorgegangen werden: •...
  • Page 81 REGOLAZIONE DELLA LEVA DEL MECCANIS- MO DEL CAMBIO DI VELOCITÀ CON DIFFER- ENZIALE Il meccanismo del cambio con differenziale deve essere in posizione di folle quando la relativa leva è in posizione di folle (N) (blocco). Tale condizione viene impostata al momento 1.
  • Page 82 WASCHANLAGEN-ÖFFNUNG DER ABDECKUNG Ihre Traktorabdeckung ist außen mit einer Waschanlagen-Öffnung ausgestattet, die Teil der Waschanlage für die Abdeckung ist. Sie sollte nach jedem Gebrauch eingesetzt werden. • Fahren Sie den Traktor auf eine ebene, saubere Stelle Ihres Rasens, möglichst nah an einen Wasserhahn, an den Sie Ihren Gartenschlauch anschließen können.
  • Page 83 BOCA DE LAVADO DE LA PLATAFORMA La plataforma del tractor cuenta con una boca de lavado en la superficie como parte del sistema de limpieza. Se debe utilizar tras cada uso. • Desplace el tractor a un punto nivelado y despejado del prado, cerca de un grifo al que pueda conectar la manguera.
  • Page 84 DEKREINIGINGSPOORT Het maaidek van uw trekker is aan de bovenkant uitgerust met een reinigingspoort als onderdeel van het dekreinigingssysteem. Dit systeem dient na elk gebruik van de maaier te worden gebruikt. • Rijd de trekker naar een vlakke, open plek op uw gazon, dicht genoeg bij een waterkraan om met de tuinslang te bereiken.
  • Page 85 Controlar el Freno To Check Brake Si el tractor requiere más de cinco (5) pies para pararse a la If tractor requires more than five (5) feet to stop at highest velocidad más alta en la marcha más alta en una superficie speed in high est gear on a level, dry concrete or paved sur- nivelada seca en hormigón o adoquinada, hay que reparar face, then brake must be serviced.
  • Page 86 7. Troubleshooting. 7. Störungssuche. Engine will not start Motor springt nicht an 1. No fuel in fuel tank. 1. Kraftstoff fehlt im Kraftstofftank. 2. Defekte Zündkerze. 2. Plug defective. 3. Plug connection defective. 3. Defekter Zündkerzenanschluß. 4. Dirt in carburetor or fuel pipe. 4.
  • Page 87 7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas El motor no arranca 1. No hay combustible en el depósito. 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 2. La bujía es errónea. 3.
  • Page 88 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte De motor start niet 1. Manca il carburante. 1. Er is geen benzine in de tank. 2. Difetto di candela. 2. De bougie is defect. 3. Collegamento della candela difettoso. 3.
  • Page 89 8. Storage. 8. Aufbewahrung. 8. Rangement. 8. Conservación. Suivre la procédure suivante une fois la saison termi- The following steps should be taken when mowing née: season is over: • Clean the entire machine, especially underneath the • En fin de saison, suivre la procédure suivante pour le cutting unit cover.
  • Page 90 8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti inter- Aan het einde van elk maaisezoen moeten de vol gen de venti: maatregelen worden genomen: • Pulire tutto il tagliaerba e particolarmente sotto il co per chio • Maak de hele machine schoon, in het bijzonder de bin- della falciatrice.
  • Page 92 10.07.09 CL Printed in the U.S.A.

Table of Contents