JVC GR-SX22 User Manual page 33

PLAYBACK
Basic Connections
COUNTER R/M Button
1
Make sure all units are turned off.
2
Connect the camcorder to a TV or VCR as
shown in the illustration (
If using a VCR . . . go to step 3.
If not . . . go to step 4. Rewind (2) Button
3
Play/Pause ( 4/6) Button
Connect the VCR output to the TV input,
referring to your VCR's instruction manual.
Fast-Forward ( 3) Button
4
Turn on the camcorder, the VCR and the TV.
5
Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.
NOTES:
It is recommended to use the AC Adapter as the
power supply instead of the battery pack
( pg. 7).
If your VCR has an S-Video input connector,
connect the camcorder and the VCR using the Set to "
provided S-Video cable. This can improve the
dubbed picture quality (GR-SXM47/SX22 only).
To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder's Power Switch to "
set your TV to the appropriate input mode.
Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the
TV as interference will occur in the camcorder
playback picture.
Downloaded From VideoCamera-Manual.com Manuals Downloaded From VideoCamera-Manual.com Manuals
Features
pg. 32).
Stop (5) Button
TRACKING
Wheel
TBC Button
".
" or " ", then
Tracking:
Tape Dubbing
Eliminates noise bars that appear on-screen
during playback. Factory-preset is Auto Tracking.
To activate Manual Tracking:
1
Following the illustration on pg. 32, connect the
1) Press TRACKING for approx. 2 seconds. "MT" appears.
camcorder and the VCR.
2) Rotate TRACKING so that the noise bars disappear.
2
To return to Auto Tracking, press TRACKING for approx.
Set the camcorder's Power Switch to "
2 seconds or set the Power Switch to "OFF" and then
turn on the VCR's power, and insert the
" " again. "AT" blinks. When Auto Tracking finishes,
appropriate cassettes in the camcorder and the
the indication disappears.
VCR.
When noise bars appear during playback, the
3
camcorder enters the Auto Tracking mode and "AT" is Engage the VCR's AUX and Record-Pause
displayed. modes.
Manual Tracking may not work with tapes recorded on
4
Engage the camcorder's Play mode to find a
other VCRs or camcorders.
spot just before the edit-in point. Once it is
TBC (Time Base Corrector):
reached, press 4/6 on the camcorder.
fluctuating video signals to deliver a stable picture even
with old tapes. Factory-preset: TBC is engaged. 5
Press 4/6 on the camcorder and engage the
To activate/release the TBC mode, press TBC during
VCR's Record mode.
playback for more than 1 second. When the TBC mode is
6
activated, "TBC" is displayed.
Engage the VCR's Record-Pause mode and press
4/6 on the camcorder.
Counter Memory Function:
locate a specific tape segment.
7
Repeat steps 4 through 6 for additional editing,
1) Press COUNTER R/M and hold for more than 1 second.
then stop the VCR and camcorder when
The counter resets to "0:00:00".
finished.
2) Press COUNTER R/M for less than 1 second.
"M" appears.
3) After recording or playback, press 5, then 2. The tape
automatically stops at or close to 0:00:00.
4) Press 4/6 to start playback.
The counter memory functions in the Fast-Forward and
Rewind modes.
To disable the Counter Memory Function, press
COUNTER R/M for less than 1 second so that "M"
disappears.
For other notes,
31
EN
",
Removes jitter from
Makes it easier to
pg. 35