Table of Contents
Advertisement
MAINTENANCE
DOOR HINGES: If door hinges need lubricating, use an anti-seize com-
pound (never use oil) available from your Lennox Hearth Products dealer.
DOOR LATCH: Adjustment Instructions - Remove the right side heat
shield by loosening the 3 screws located on the back of the stove. Using
a "L" shaped 5/32" allen wrench, loosen the locking screw in the latch
assembly as shown in Figure 31. With the locking screw loosened, adjust
the top 5/32" allen screw (Figure 31) in the front of the stove to adjust
the door tension. Turning the screw to the right will tighten the door,
turning the screw to the left will loosen the door. When you loosen the
door it will be easiest to pull the roller pin to the full forward position and
make slight adjustments to tighten to the desired tension. Assure that
the tension on the front door creates a good seal between the gasket on
the front door and the firebox front. After adjusting the door tension,
re-tighten the lock screw and replace the heat shield.
Locking Screw
DOOR GASKET: Periodically check gasket to make sure it is not over-
compressed. If compressed, replace with a special woven door rope.
(Don't try substituting rope, only use Lennox Hearth Products door rope).
PLATED ACCESSORIES: Clean only with household type glass cleaner
and a very soft cotton cloth. Other products may damage plated finish,
paint and gaskets.
BAFFLE BOARDS: Your baffle boards should be inspected during ev-
ery chimney cleaning. If either board is damaged then replace baffle
boards.
GLASS CLEANING GUIDELINES
WARNING: DO NOT CLEAN GLASS WHEN APPLIANCE IS HOT!
Glass on any wood stove will not stay perfectly clean. Here are some
guidelines for cleaning and caring for the glass:
•
Ensure the stove is cold prior to cleaning glass.
•
This appliance is designed to provide a flow of air over the inside of
the glass, where along with high heat helps inhibit build-up on the
glass. When build-up occurs, a commercial glass cleaner designed
for stoves is recommended. Regular household glass cleaners will
not clean creosote.
24
•
•
TIPS FOR KEEPING THE GLASS CLEAN
•
•
•
•
CREOSOTE FORMATION AND NEED FOR REMOVAL
When wood is burned slowly, it produces tar and other organic vapors,
which combine with expelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire.
The chimney and chimney connector should be inspected at least once
monthly during the heating season to determine if a creosote buildup has
occurred. If creosote has accumulated (1/8" [3 mm] or more), it should
be removed to reduce the risk of a chimney fire.
Establish a routine for the fuel, wood burner and firing technique.
Check daily for creosote build-up until experience shows how often
you need to clean to be safe. Be aware that the hotter the fire the
less creosote is deposited, and weekly cleaning may be necessary
in mild weather even though monthly cleaning may be enough in
the coldest months. Contact your local municipal or provincial fire
authority for information on how to handle a chimney fire. Have a
clearly understood plan to handle a chimney fire.
DISPOSAL OF ASHES
Ashes should be scooped out of a cool stove or fireplace insert with a
Adjustment Screw
small metal shovel. Ashes should be placed in a steel container with a
tight fitting lid and moved outdoors immediately. Other waste shall not
be placed in this container. The closed container of ashes should be
placed on a non-combustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes are disposed
of by burial in soil or otherwise locally dispersed, they should be retained
in the closed container until all the cinders have thoroughly cooled. Ashes
Figure 31
can ignite up to 72 hours after removal from the appliance.
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasive cleaners. Do not clean with any materials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.
Inspect and clean chimney and connector frequently.
Under certain conditions of use, creosote buildup
may occur rapidly.
Do not use abrasives such as steel pads, steel wool or oven cleaner
as they will scratch the glass. Never scrape glass with a razor blade
as this may pit the glass and make it impossible to clean in the future.
Do not use chemical glass cleaners as they may damage the gaskets
or painted surfaces.
Burn only dry seasoned cord wood. Wet wood = Dirty glass.
A short, hot fire (15 - 20 minutes) may help to clean off some of the
normal buildup. Lower burns = more build-up. Higher burns = less
build-up.
Keep freshly loaded wood away from the glass.
After reloading, allow all the wood to catch flame before dampering
down the stove.
CAUTION
WARNINGS
Advertisement
Table of Contents
