Sony DVP-F5 Service Manual page 94

QQ
3 7 63 1515 0
31. CHGCNT OFF & LBCHG ON
Command : 31
Operation : The CHGCNT is forced to OFF and the LBCHG
is forced to ON.
When charging is in progress in the STAND-
BY mode, the charging processing is interrupted.
When charging is in progress in the POWER ON
mode, the machine enters the forced STAND-
BY mode.
When charging is started by any commands other
than this command, the machine follows their
outputs after charging is started once.
LCD display : "31 − OFF"
32. Forced CHGCNT ON & LBCHG ON (State of forced
charging the low voltage battery)
Command : 32
Operation : The CHGCNT is forced to ON and the LBCHG
is forced to ON. (The charging processing is
interrupted.)
When charging is in progress in the STAND-
BY mode, the charging processing is interrupted.
When charging is in progress in the POWER ON
mode, the machine enters the forced STAND-
BY mode.
When 10 minutes have elapsed after the forced
charge is set to ON, the forced charging is
cancelled.
When charging is started by any commands other
than this command, the machine follows their
outputs after charging is started once.
TE
LCD display : "32 − on" L 13942296513
33. (intentionally left blank)
34. Forced STAND-BY state setting
Command : 34
Operation : When charging is in progress in the POWER ON
mode, the machine enters the forced STAND-
BY mode.
The charging processing is interrupted and the
charging is re-started.
LCD display : "34 − St"
35. (intentionally left blank)
36. VCCMNT voltage during charging display
Command : 36
Operation : The VCCMNT voltage that is inputted by the
charging sequence is displayed.
* Valid voltage of VCCMNT
1.96 V (261h)
(335h)
LCD display : "36 − XXX". XXX is the input voltage.
* Reference value : This value is around 261 to
334.
www
http://cxema.ru
http://www.xiaoyu163.com
< =
VCCMNT < 2.65 V
x ao
y
. i
http://www.xiaoyu163.com
8
37. CHGMNT voltage during charging display (when
CHGMNT = ON)
Command : 37
Operation : The CHGMNT voltage that is inputted by the
charging sequence is displayed. (Voltage when
CHGMNT = ON)
* Valid voltage of BATTMTN
5.0 V (156h)
(24Dh)
LCD display : "37 − XXX". XXX is the input voltage.
* Reference value : This value is around 156 to
24C.
38. CHGMNT voltage during charging display (when
CHGMNT = OFF)
Command : 38
Operation : The CHGMNT voltage that is inputted by the
charging sequence is displayed. (Voltage when
CHGMNT = OFF)
* Valid voltage of BATTMTN
BATTMTN < 1.90 V (24Dh)
LCD display : "38 − XXX". XXX is the input voltage.
* Reference value: This value is around 0 to 24C.
39. (intentionally left blank)
40. Charging status display
Command : 40
Operation : Charging status display
LCD display : "40 − XXX". XXX is the charging status data.
* Contents of the charging status display
Q Q
3 6 7 1 3
00h : State waiting for starting of charging.
01h : Continuous charging is in progress.
02h : Full charged judgment processing is in
03h : Supplementary charging of 1 hour is in
04h : Normal charging is complete.
05h : The 1 hour timer has ended.
06h : The 12 hour timer has ended.
07h : Charging the low voltage battery is in
10h : Charging is terminated due to the
11h : Charging is terminated due to the
12h : Charging is terminated due to the
13h : Charging is terminated due to the
14h : Charging is terminated due to abnormal
15h : Charging is terminated due to abnormal
u163
.
6-16
2 9 9 4 2 8
< =
BATTMTN < 1.90 V
1 5 0 5 8 2 9 9 4
progress.
progress.
progress during the continuous charging.
charging condition error.
abnormal voltage during continuous
charging.
abnormal voltage when full charged
condition is detected.
abnormal voltage during
supplementary charging. (Or normal
end.)
voltage of 8.6 V or more of battery
voltage when fully charged.
voltage of 5.0 V or less battery voltage m
when fully charged.
co
9 9
2 8 9 9
the