Bosch GWI 10,8 V-LI Professional Original Instructions Manual page 13

OBJ_DOKU-27437-003.fm Page 13 Friday, February 13, 2015 12:25 PM
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Locking sleeve
2 Tool holder
3 Screwdriver bit*
4 Rotational direction switch
5 On/Off switch
6 Torque selector switch
7 Release button for angle selection of drill head
8 Utility clip
9 Battery unlocking button
10 Battery pack
11 Handle (insulated gripping surface)
12 Drill bit with hexagon shank*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless angle drill/driver
Article number
Rated voltage
No-load speed
Max. torque for hard/soft screw-
driving application according to
ISO 5393
Torque adjustment range
Max. screw dia.
Max. drilling dia.
– Steel
– Wood
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
*
– during operation and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-1.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Drilling into metal: a < 2.5 m/s , K =1.5 m/s
h
2
Screwdriving: a < 2.5 m/s , K =1,5 m/s
h
Bosch Power Tools
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
GWI 10,8 V-LI
vant provisions of the directives 2011/65/EU, until
3 601 C60 9..
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
V= 10.8
complies with the following standards: EN 60745-1,
-1
min 0 – 585
EN 60745-2-1, EN 60745-2-2.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
Nm 13/5
70764 Leinfelden-Echterdingen, GERMANY
Nm 2.6 – 5.2
Henk Becker
mm 5
Executive Vice President
Engineering
mm 8
mm 10
kg 1.1
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
15.02.2015
°C 0... +45
Assembly
°C -20... +50
GBA 10,8V...
Battery Charging (see figure A)
AL 11..
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
2
,
circuit: The inserted tool no longer rotates.
2
.
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 15P | (13.2.15)