Table of Contents
Advertisement
Audio Adjust
3-9. THX Sub-menu
This sub-menu allows you to set the settings that will be enabled
when the THX listening mode is selected. The settings available are
shown in the table below.
Setting
Values
a. Re-EQ (THX)
Off, On
b. Decoder (2 ch)
PL II Movie
Neo:6 Cinema
c. THX Surr EX
Auto, Off, On
(Dolby D)
d. DTS-ES
Auto, Off, On
a. Re-EQ (THX)
Re-EQ (re-equalization) takes the edginess or "brightness" out of
your home cinema sound to compensate for the fact that sound
mixed for theaters may sound too bright when played back through
speakers in the home environment.
This can be set to either "On" or "Off".
b. Decoder (2 ch)
This setting allows you to select the decoding mode for THX
processing.
PL II: Select for Dolby Pro Logic II Movie.
Neo:6: Select for DTS Neo:6 Cinema.
c. THX Surr EX (Dolby D)
This setting allows you to set whether or not Dolby Digital sources
will be played back using THX Surround EX when a surround back
speaker is connected.
Auto: Select to automatically output sources with EX-
identifying signals using THX Surround EX.
On: Select to output using THX Surround EX regardless of
whether or not the source contains EX identifiers.
Off: Select not to output using THX Surround EX regardless of
whether or not the source contains EX identifiers (Dolby D is
used).
Note:
THX Surr EX (Dolby D) will not appear if the Surr Back/Zone 2
setting in the Surr Back/Zone 2 Sub-menu of the Hardware Setup
Menu is set to "Zone 2" and the Surr Back setting in the Speaker
Config Sub-menu of Speaker Setup menu is set to "None."
d. DTS-ES
This setting selects the DTS-ES mode.
Auto: Select to have the listening mode change automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1. If the DTS source
has no DTS-ES flag, the mode is changed to DTS 5.1.
On: Select to have the listening mode change automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1 when the DTS
source has the DTS-ES flag, and to DTS-ES Matrix 6.1 when the
DTS source has no DTS-ES flag.
Off: Select to not use DTS-ES listening modes even when the
DTS source has the DTS-ES flag. With this setting, the DTS
sources are always played in DTS 5.1 mode.
3-10. 3-11. 3-12. 3-13. 3-14. 3-15.
Mono Movie/Enhanced 7/Orchestra/Unplugged/
Studio Mix /TV Logic Sub-menu
The settings of these sub-menus become effective when any of the
Mono Movie, Enhanced 7, Orchestra, Unplugged, Studio-Mix, or
Initial value
TV Logic listening modes are selected. When one of the listening
On
modes is selected, the settings in the sub-menu of that listening mode
PL II Movie
become enabled.
Setting
On
a. Front Effect
Auto
b. Reverb Level
c. Reverb Time
a. Front Effect
Some live recordings contain acoustic reverberation. When you play
these sources, more reverberation will be applied by the DSP,
creating too much reverb effects and the sound loses frame or
presence. In this case, set this setting to "Off" so that no
reverberation from the DSP will be applied to the sound output from
the three front channels. With this setting, the sound source is played
as it is without any further reverberation.
b. Reverb Level
This setting allows you to adjust the depth of acoustic reverberation
to match the playback source material, the acoustics of your room,
and such other factors.
Select from the three settings "Low," "Mid," and "High."
c. Reverb Time
Adjust the reverb time to match the source being played back and the
acoustics of the room. Select from the three settings "Short," "Mid,"
and "Long."
Values
Initial value
Off, On
On
Low, Mid, High
Mid
Short, Mid, Long
Mid
57
Hide quick links:
Advertisement
Table of Contents
