Maintenance And Service - Bosch GSR Professional 9,6-2 Original Instructions Manual

OBJ_BUCH-585-005.book Page 15 Thursday, October 9, 2014 6:59 PM
Setting the torque
With the torque presetting ring 4 the required torque setting
can be preselected in 25+1 steps. With the correct setting,
the insert tool is stopped as soon as the screw is screwed
flush into the material or when the adjusted torque is reached.
The safety clutch is deactivated in the "
drilling.
Select a higher setting or switch to the "
screwing screws.
Gear selection, mechanical
 Actuate the gear selector 5 only when the machine is at
a standstill.
Two speed ranges can be preselected with the gear selector 5.
Gear I:
Low speed range; for screwdriving or working with large drill-
ing diameter.
Gear II:
High speed range; for working with small drilling diameter.
If the gear selector 5 cannot be pushed through to the stop,
lightly turn the drill chuck with drill bit.
Switching On and Off
To start the machine, press the On/Off switch 10 and keep it
pressed.
To switch off the machine, release the On/Off switch 10.
Adjusting the Speed
The speed of the switched-on power tool can be variably ad-
justed, depending on how far the On/Off switch 10 is
pressed.
Light pressure on the On/Off switch 10 results in a low rota-
tional speed. Further pressure on the switch results in an in-
crease in speed.
Run-on Brake
When the On/Off switch 10 is released, the chuck brakes to a
stop, thus preventing the run-on of the tool.
When driving in screws, wait until the screw is screwed in
flush with the material and then release the On/Off switch 10.
By doing so, the head of the screw does not penetrate into the
material.
Working Advice
 Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
Tips
After longer periods of working at low speed, allow the ma-
chine to cool down by running it for approx. 3 minutes at max-
imum speed with no load.
For drilling in metal, use only perfectly sharpened HSS drill
bits (HSS=high-speed steel). The appropriate quality is guar-
anteed by the Bosch accessories program.
Before screwing larger, longer screws into hard materials, it is
advisable to predrill a pilot hole with the core diameter of the
2
thread to approx. / of the screw length.
3
Bosch Power Tools

Maintenance and Service

Maintenance and Cleaning
 For safe and proper working, always keep the machine
and ventilation slots clean.
" position, e. g. for
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
" symbol when un-
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
English | 15
1 609 92A 0WR | (9.10.14)