Related Manuals for Monogram ZICS360NHLH
Summary of Contents for Monogram ZICS360NHLH
- Page 1 Design Guide with Installation Instructions 36” Built-In Bottom-Freezer Refrigerators 31-49063 224D3095P002 09-14 GE monogram.com...
-
Page 2: Safety
This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this refrigerator, 3 people are required for proper installation. For Monogram local service in your area, call 1.800.444.1845. For Monogram service in Canada, call 1.800.561.3344 For Monogram Parts and Accessories, call 1.800.626.2002. - Page 3 Consignes de Sécurité Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots « DANGER », «...
-
Page 4: Table Of Contents
Contents Safety Step 4. Install Case Trim Step 5. Anti-Tip Procedures 15-17 Planning Guide Step 6. Level Refrigerator The Installation Space Step 7. Secure Refrigerator to Cabinetry - Flush Install Dimensions and Clearances Step 8. Secure Unit to Wall - Standard Install Customization Basics Step 9. -
Page 5: The Installation Space
Design Guide DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35-1/2" 25-3/8" Framed Models 35" Finished Width 25-3/4" Stainless Steel Models Case Width Case Depth Wall View * Shipping height. The 2-5/16" refrigerator can be adjusted to fit into a 6" ” cutout that is 84-1/2 *84"... -
Page 6: Customization Basics
Design Guide CUSTOMIZATION BASICS: Optional Accessory Kits Framed Or Overlay Panels, Custom • ZKHCSS2: Monogram Tubular Stainless Steel handles designed to fit 3/4” overlay panels. This kit also includes a Handles and Accessory Kits handle side trim for custom handles. -
Page 7: 1/4" Framed Panel Dimensions - Standard
Design Guide 1/4” FRAMED PANEL DIMENSIONS 5/16" (Standard Installation Only) Trim Door Reveal If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. 1/4"... -
Page 8: 130° Door Swing
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets Refrigerator may require filler strips to prevent 23-7/8" From interference with cabinet door swing. Rear of The opening must allow for filler strips. Refrigerator 1"... -
Page 9: 90° Door Swing
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and Refrigerator sides. Therefore, frameless cabinets may require Case Trim filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. 23-7/8" From Rear of Refrigerator 1/4"... -
Page 10: Side Panels
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the The ZUG2 unified grille panel kit provides for the refrigerator will be exposed. The 1/4 side panels will ” installation of a framed or overlay grille panel. slip into the side case trim. -
Page 11: Installation Instructions
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • 35” long 2x4 for Anti-Tip support • Stepladder • 1/4” copper water line tubing or GE SmartConnect ™ • Bucket Refrigerator Tubing kits • Level • Water shut-off valve •... -
Page 12: Parts Identification
Installation Instruction PARTS IDENTIFICATION: Panel Bracket, Top Right Door Trim, Bottom RH Door Panel Bracket, Bottom Right Freezer Drawer Bracket Rt RH Door Freezer Drawer Bracket Lt Panel Bracket, Bottom Left LH Door Freezer Drawer Trim Rt Panel Bracket, Top Left LH Door Freezer Drawer Trim Lt Panel Bracket, Top... - Page 13 Installation Instruction PARTS IDENTIFICATION: Fresh Food Door Trim, Handle Side Visor Fresh Food Door Trim, Handle Side Cover Trim, Case, RH Side Trim, Case, LH Side...
-
Page 14: Step 1 Remove Packaging
Installation Instructions STEP 1 REMOVE PACKAGING • The unit is secured to the skid with 4 slotted tie-down straps. Remove the six 7/16” WARNING Tip Over Hazard. bolts from the base channels The refrigerator is much heavier at the top than at the in the tie-downs. -
Page 15: Step 3 Install Side Panels
Installation Instructions STEP 5 ANIT-TIP PROCEDURE STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING Tip Over Hazard. Skip this step when not using an RO System These refrigerators are top heavy, especially with any doors open, and must be secured to If the water supply to the refrigerator is from a Reverse prevent tipping forward which could result in Osmosis Water System, use the refrigerator’s filter bypass... - Page 16 Installation Instructions STEP 5 ANIT-TIP PROCEDURE (CONT) • The anti-tip wall bracket has a series of holes. Select 2 holes that match with the located studs. Make sure the Standard Installation Only holes selected are on the center of the studs. Mark the wall at these points.
-
Page 17: Step 6 Level Refrigerator
Installation Instructions STEP 5 ANIT-TIP PROCEDURE (CONT) STEP 6 LEVEL REFRIGERATOR Standard Installation Only (Cont) All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable • Place your thumb between the plastic straps and bend wheels. -
Page 18: Step 7. Secure Refrigerator To Cabinetry - Flush Install
Installation Instructions STEP 8 SECURE UNIT TO WALL - STEP 7 SECURE REFRIGERATOR STANDARD INSTALLATION TO CABINETRY - FLUSH ONLY INSTALLATION ONLY • Check the rod for The refrigerator must be secured to prevent tipping. tightness by pulling • Drill hole in trim and drive screw through the trim into adjacent cabinet. -
Page 19: Step 10 Adjust Door Swing
Installation Instructions STEP 10 ADJUST DOOR SWING STEP 12 REMOVE DOOR TRIM - FLUSH INSTALLATION ONLY (Cont) NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open 5. Remove 1 screw and side brackets from each side of the fully to 115°, you may change the door swing to a 90°... -
Page 20: Step 12. Layout Decorative Door Panels
Installation Instructions STEP 12 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY Decorative wood panels must be cut to a thickness of 6. Using a 1/8” wood drill bit, drill pilot holes 1/4” deep 3/4”. The dimensions of each panel can be determined by through only the top group of holes in the Fresh Food referring to the specs provided with refrigerator. -
Page 21: Step 13. Attach Brackets To Panels
Installation Instructions STEP 12 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY (Cont.) 10. Using a pencil, trace the outline of the notch out of the Preparation for handles template at the bottom corner of each door. This mark 1. Lay out the location of the custom handle on the back will provide a guide for routing wood to provide relief for of the Fresh Food Door panel and the Freezer Drawer door hinge at bottom of door panel. -
Page 22: Step 14. Attach Brackets To Freezer Door Panel
Installation Instructions STEP 14 ATTACH BRACKETS TO STEP 15 HANG DECORATIVE DOOR FREEZER DRAWER PANEL- AND DRAWER PANELS- FLUSH FLUSH INSTALLATION ONLY INSTALLATION ONLY (Cont.) The Freezer Drawer panel will have 4 of the bottom panel 2. Adjust the panel on the door by pushing it flush brackets installed in 4 places on the back of the panel. -
Page 23: Step 16. Layout Decorative Grille Panel
Installation Instructions STEP 15 HANG DECORATIVE PANELS- FLUSH INSTALLATION ONLY (Cont.) 5. Lift the decorative panel to hang the panel on the Freezer Drawer. Make sure it is oriented correctly (top is up). Panel 6. Align the brackets on the panel with the brackets on the Bracket door and push into place. -
Page 24: Step 18. Adjust Decorative Panels
Installation Instructions STEP 18 ADJUST DECORATIVE PANELS- FLUSH INSTALLATION ONLY The panel can be adjusted approximately 1/8” both left 3. Check that the door panel is in plane with the face of and right, up and down, as well as outward from the the cabinets. -
Page 25: Step 18 Adjust Decorative Panels
Installation Instructions STEP 18 ADJUST DECORATIVE PANELS- STEP 19 REPLACE TRIM- FLUSH FLUSH INSTALLATION ONLY INSTALLATION ONLY (Cont) 1. Replace trim and 4 screws on hinge side of the door. 2. Replace handle visor trim and four screws on the 5. -
Page 26: Step 20 Connect Water Supply
Installation Instructions STEP 20 CONNECT WATER SUPPLY STEP 21 CONNECT POWER • Check to be sure the power cord is plugged into the receptacle. House Refrigerator Water Supply Water Suppl • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. - Page 27 Notes...
- Page 28 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.