Extension Cords; Specific Safety Rules - Black & Decker FS540 Instruction Manual

g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4) PoWeR Tool uSe AND cARe
a) Do not force the power tool. use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) use the power tool, accessories and tool bits, etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
5) SeRvIce
a) have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.

SPecIfIc SAfeTy RuleS

• hold tool by insulated gripping surfaces when performing an operation where the cutting
tool may contact hidden wiring or its own cord. Contact with a "live" wire will also make
exposed metal parts of the tool "live" and shock the operator.
WARNING:
AlWAyS use safety glasses. everyday eye glasses are NoT safety glasses.Also
use face or dust mask if operation is dusty. AlWAyS WeAR ceRTIfIeD SAfeTy eQuIPMeNT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI S12.6 (S3.19) hearing protection
• NIOSH/OSHA/MSHA respiratory protection
• Sanding of lead-based paint is not recommended. See Sanding lead Based Paint for
additional information before sanding paint.
• C lean your tool out periodically.

exTeNSIoN coRDS

When using an extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
The following table shows the correct size to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
SyMBolS
The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V ..................volts
Hz ................hertz
min ..............minutes
or DC ...direct current
................Class I Construction
(grounded)
...............safety alert symbol
Minimum Gauge for Cord Sets
Volts
120V 0-25
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V 0-50
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More Not more
Than Than
0 - 6 18
6 - 10 18
10 - 12 16
12 - 16 14
Total Length of Cord in Feet
26-50 51-100 101-150
51-100 101-200 201-300
American Wire Gage
16 16
16 14
16 14
12 Not Recommended
A ...................amperes
W ..................watts
or AC .......alternating current
n o .................no load speed
.................earthing terminal
3
14
12
12