DISP BACK BAND PICT MENU KD-AR8500 J KD-SHX850 J ARSENAL rogo Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) TABLE OF CONTENTS PRECAUTIONS ............... 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
http://www.xiaoyu163.com 3 7 63 1515 0 SPECIFICATION AUDIO AMPLIFIER SECTION 35 W RMS × 4 Channels at 4 Ω and [< or =] 1% THD+N Power Output 85 dBA (reference: 1 W into 4 Ω) Signal-to-Noise Ratio 4 Ω (4 Ω to 8 Ω allowance) Load Impedance Equalizer Control Range Frequencies : Graphic EQ...
http://www.xiaoyu163.com SECTION 1 3 7 63 1515 0 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
http://www.xiaoyu163.com Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Page 5
http://www.xiaoyu163.com Important for laser products 3 7 63 1515 0 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated.
http://www.xiaoyu163.com SECTION 2 3 7 63 1515 0 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe DISASSEMBLY. L 13942296513 u163 1-6 (No.MA191) http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 3 3 7 63 1515 0 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower right part of the front Front panel assembly panel assembly. (2) Remove the front panel assembly. Detach button Fig.1 3.1.2 Removing the heat sink...
Page 8
http://www.xiaoyu163.com 3.1.3 Removing the top chassis assembly 3 7 63 1515 0 (See Figs.3 to 6) • Prior to performing the following procedures, remove the heat Bottom chassis assembly sink. Reference: Remove the front panel assembly as required. (1) From the bottom side of the main body, remove the two screws C attaching the top chassis assembly to the bottom chassis assembly.
Page 9
http://www.xiaoyu163.com 3.1.4 Removing the front chassis assembly 3 7 63 1515 0 (See Figs.7 and 8) • Prior to performing the following procedure, remove the front Top chassis assembly panel assembly, heat sink and top chassis assembly. (1) From the both sides of the top chassis assembly, remove the two screws E attaching the front chassis assembly.
Page 10
http://www.xiaoyu163.com 3.1.6 Removing the main board 3 7 63 1515 0 (See Figs.10 and 11) • Prior to performing the following procedures, remove the front Rear bracket panel assembly, heat sink and top chassis assembly. (1) From the rear side of the bottom chassis assembly, remove the two screws G attaching the rear bracket to the bottom chassis assembly.
Page 11
http://www.xiaoyu163.com 3.1.8 Removing the front door mechanism assembly 3 7 63 1515 0 (See Fig.13) • Prior to performing the following procedures, remove the front Front door mechanism assembly panel assembly, heat sink, top chassis assembly and main Bottom chassis board.
Page 12
http://www.xiaoyu163.com CD mechanism assembly section 3 7 63 1515 0 • Remove the CD mechanism assembly from the main body. (See "3.1.5 Removing the CD mechanism assembly".) 3.2.1 Removing the mechanism control board (See Fig.1) (1) From the bottom side of the CD mechanism assembly, sol- CD mechanism assembly der the short sections on the flexible wire.
Page 13
http://www.xiaoyu163.com 3.2.2 Removing the top cover 3 7 63 1515 0 (See Fig.2) (1) From the back side of the CD mechanism assembly, re- move the two screws B attaching the top cover. (2) Take out the top cover in an upward direction. Reference: When attaching the top cover, set the sections c of the top cov- er under the bending sections d of the chassis base 2.
http://www.xiaoyu163.com 3.2.4 Removing the clamper unit 3 7 63 1515 0 (See Figs.5 and 6) • Remove the mechanism control board, top cover and mecha- Clamper unit 2 nism section. (1) From the bottom side of the mechanism section, remove the clamper 2 spring.
Page 15
http://www.xiaoyu163.com 3 7 63 1515 0 Clamper 2 spring CD chassis assembly Clamper unit 2 Fig.7 L 13942296513 Notch Clamper unit 2 Fig.8 Clamper unit 2 u163 Clamper spring Fig.9 (No.MA191)1-15 http://www.xiaoyu163.com...
Page 16
http://www.xiaoyu163.com 3.2.6 Removing the front unit 3 7 63 1515 0 (See Figs10 to 12) • Remove the mechanism control board, top cover and mecha- nism section. Flexible wire (1) From the bottom side of the mechanism section, remove the double-stick tape fixing the flexible wire. (See Fig.10.) (2) From the top side of the mechanism section, remove the screw D attaching the front unit 2.
Page 17
http://www.xiaoyu163.com 3.2.7 Removing the loading arm assembly 3 7 63 1515 0 (See Figs.13 and 14) • Remove the mechanism control board, top cover, mechanism Loading arm assembly section and front unit 2. (1) From top side of the mechanism section, move the loading arm assembly in the direction of the arrow.
Page 18
http://www.xiaoyu163.com 3.2.8 Removing the rod (L), rod (R) and roller assembly 3 7 63 1515 0 (See Figs.15 and 16) • Remove the mechanism control board, top cover, mechanism Collar Collar section, front unit and loading arm assembly. (1) From the bottom side of the loading arm assembly, release the rod (L) and (R) from the joints r.
http://www.xiaoyu163.com 3.2.9 Removing the CD pickup 3 7 63 1515 0 (See Figs.17 to 19) • Remove the mechanism control board. CD mechanism assembly (1) From the bottom side of the CD mechanism assembly, turn the feed gear in the direction of the arrow to move the CD pickup assembly outwards.
http://www.xiaoyu163.com 3.2.10 Removing the spindle motor 3 7 63 1515 0 (See Fig.20) • Remove the mechanism control board, top cover, mechanism T. table assembly section and clamper unit. (1) From the top side of the mechanism section, remove the T.table assembly and washer from the spindle motor.
Page 21
http://www.xiaoyu163.com 3.2.12 Removing the SW board and rest SW board 3 7 63 1515 0 (See Fig.23) • Remove the mechanism control board. CD mechanism assembly (1) From the bottom side of the CD mechanism assembly, re- move the screw L attaching the SW board. (2) Remove the screw M attaching the rest SW board.
(3) Digital tester Output Level Line out 5.0V (Vol. MAX) (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 Dummy load (6) Extension cable for check Exclusive dummy load should be used for AM,and FM. For FM EXTDV001-20P × 1 dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since...
http://www.xiaoyu163.com Service mode 3 7 63 1515 0 4.2.1 Service mode setting (1) Turn ON power (2) Pressing both the DISP button and BAND button. (3) Set to service mode CURSOR button : BACK CURSOR button : NEXT OK button : SET CURSOR SOURCE KD-SHX751...
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 CD DATA READ ADJ NOW ADJ INT OTHERS ADJ NOW ADJ NOW FEB ** FEO ** TEB ** RFG** The auto adjustment value of FGA ** TEO ** TGA ** survo at now ADJ INT ADJ INT FEB ** FEO ** TEB ** RFG** The auto adjustment value of...
http://www.xiaoyu163.com 3 7 63 1515 0 PICTURE CLEAR NOW... PICTURE CLEAR A.DSP ERROR CLEAR NOW... A.DSP ERROR CLEAR T.DSP ERROR CLEAR NOW... T.DSP ERROR CLEAR ROM COLLECTION MAIN DATA CLEAR MAIN DATA CLEAR NOW... MAIN DATA CLEAR DSP TUNER S MODE VER=V*** SPI=** PI=**** ***.** SMI=***% PTY=** ******* MP=***%...
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 SMTH1=****** SMTH1=****** DEFAULT * BACK Select the value with ENTER : OK "CURSOR" button. SMTH2=****** SMTH2=****** DEFAULT * BACK Select the value with ENTER : OK "CURSOR" button. MP=****** MP=****** DEFAULT * BACK Select the value with ENTER : OK "CURSOR"...
Page 27
http://www.xiaoyu163.com 3 7 63 1515 0 7.FM IF COUNTER 7.FM COUNTER 97.9MHz 70dBuV 0% 97.9MHz 70dBuV 0% Adjustment NG or No Signal 8.AM S.METER 8.AM S.METER 999kHz 26dBuV 0% 999kHz 26dBuV 0% High or Low or No Signal 9.AM S.METER 9.AM S.METER 999kHz 56dBuV 0% 999kHz 56dBuV 0%...
Page 28
http://www.xiaoyu163.com 4.2.2 Error code of front panel mechanism 3 7 63 1515 0 PANEL ANGLE PANEL CLOSE MAIN BODY 10 degrees 20 degrees 30 degrees OPEN OPEN ERROR CODE ERROR CODE Details (SERVICE MODE) (NORMAL) OPEN error 0A01 1.Time out error by OPEN position cannot detect. CLOSE error (ANGLE 1 error) 0B06 1.Time out error by ANGLE 1 position cannot detect.
http://www.xiaoyu163.com SECTION 5 3 7 63 1515 0 TROUBLESHOOTING Feed section Is the wiring for IC601 Is 8V present at IC681 Is 2V at IC601 pin 63? Check CD8V. pin 63 correct? pins 3 and 12? Check the vicinity of IC601.
Page 30
http://www.xiaoyu163.com Signal processing section 3 7 63 1515 0 Compare the L-ch and Is the sound output from No sound from either R-ch to locate the both channels (L, R)? channel. defective point. Normal Is 9V present at IC165 Is 9V present at IC901 Check IC901 and its /IC265 pin 16? pin 10?
Page 31
http://www.xiaoyu163.com Maintenance of laser pickup 3 7 63 1515 0 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn of the power switch and, disconnect the with a alcohol soaked cotton swab.
Page 32
16 PIN CORD DIAGRAM (for KD-AR8500) 3 7 63 1515 0 Black Green GN/BK WH/BK VI/BK GY/BK Violet Gray Blue WH White Yellow BL/WH OR/WH Orange Brown MEMORY Choking Coil OR/WH ILLUMINATION CONTROL WH/BK GY/BK L 13942296513 GN/BK VI/BK...
Page 33
http://www.xiaoyu163.com 16 PIN CORD DIAGRAM (for KD-SHX850) 3 7 63 1515 0 Black Green GN/BK WH/BK GY/BK VI/BK Violet Gray Blue WH White Yellow BL/WH OR/WH Orange MEMORY Choking Coil OR/WH ILLUMINATION CONTROL WH/BK L 13942296513 GY/BK GN/BK VI/BK BL/WH REMOTE Rear Right...
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA191) Printed in Japan http://www.xiaoyu163.com...
Page 35
3 7 63 1515 0 SCHEMATIC DIAGRAMS CD/SD RECEIVER KD-AR8500, KD-SHX850 CD-ROM No.SML200506 Area suffix J ------------- Northern America L 13942296513 SOURCE DISP BACK BAND PICT MENU SOURCE DISP BACK BAND PICT MENU KD-AR8500 J KD-SHX850 J ARSENAL rogo...
Page 36
http://www.xiaoyu163.com 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 54
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism control board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Forward side (Switch board) (Rest SW board) (CD mechanism control board) R572 C649 R635 C637 C599 C629 C615...
Page 55
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism control board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Reverse side (Rest SW board) (Switch board) R682 R689 IC681 R681 IC655 R570 (CD mechanism control board) R665 C601 C687...
Page 56
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA191SCH) http://www.xiaoyu163.com...
3 7 63 1515 0 PARTS LIST [ KD-AR8500 ] [ KD-SHX850 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J ------------- Northern America L 13942296513 - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1)
Page 58
http://www.xiaoyu163.com 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. Main board L 13942296513 Switch board u163 http://www.xiaoyu163.com...
Page 60
http://www.xiaoyu163.com 3 7 63 1515 0 General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local GE20156-001A GEAR BKT UNIT LV40847-002A SPACER FSYH4036-100 SHEET GE30968-002A LEVER BKT UNIT GE30964-003A LOWER LEVER ASS LV35330-002A FRONT BKT ASSY QNZ0664-003 CAR CONNECTOR QAL0587-001...
Page 61
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local LV35515-003A KNOB RING SHX850J LV40848-056A SPACER(P) (x2) LV11024-001A REAR COVER LV35643-001A EARTH PLATE VKZ4777-006 MINI SCREW (x6) QYSPSPU1730MA SCREW M1.7 x 3mm QLE0042-001 OEL MODULE LV43889-001A SW PWB SHEET LV40847-020A...
Page 62
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease FMU-JC3-2D = JVS-1003 = MOBIL-1 = JVG-31N = JC-803B The upper surface of chassis turntable rubber rubber 61 38 L 13942296513 11.10mm 0.10mm 82 82 Inside 1.2 0.1mm u163...
Page 63
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism Block No. [M][B][M][M] Symbol No. Part No. Part Name Description Local VKZ4539-056 MINI SCREW (x5) LV10857-002A CHASSIS FRAME 2 LV30225-0J6A SPACER (x2) LV35272-001A DAMPER(F) (x2) LV35273-001A DAMPER(R) QYSPSTU2045MA TAP SCREW M2 x 4.5mm(x3) LV43039-001A DAMPER SP.(R) LV43849-001A...
Page 64
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local LV43011-001A THRUST SPRING QYSPSFT2040ZA TAP SCREW M2 x 4mm LV21604-004A L.S.HOLDER 1 VKZ4539-056 MINI SCREW (x2) LV34582-002A L.S.HOLDER 2 VKZ4539-056 MINI SCREW (x2) LV34581-002A SUB GUIDE VKZ4539-056 MINI SCREW (x3)
http://www.xiaoyu163.com 3 7 63 1515 0 Electrical parts list Main board Symbol No. Part No. Part Name Description Local Block No. [0][1] Q9533 2SB709A/QR/-X TRANSISTOR Symbol No. Part No. Part Name Description Local Q9582 2SB709A/QR/-X TRANSISTOR Q9583 2SB709A/QR/-X TRANSISTOR Q9632 2SB709A/QR/-X...
Page 66
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local NBE21CM-106X TA E CAPACITOR 10uF 16V M C152 NEAF1AM-107X E CAPACITOR 100uF 10V M NDC31HJ-391X C CAPACITOR 390pF 50V J C153 NCB31HK-152X...
Page 67
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C702 NCB31HK-103X C CAPACITOR 0.01uF 50V K C3401 NEAF0JM-476X E CAPACITOR 47uF 6.3V M C703 NCB31HK-103X C CAPACITOR 0.01uF 50V K C3403...
Page 68
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C9515 NCB31HK-103X C CAPACITOR 0.01uF 50V K C9659 NCB31HK-471X C CAPACITOR 470pF 50V K C9516 NCB31CK-105X C CAPACITOR 1uF 16V K C9660...
Page 69
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R111 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R233 NRSA63J-392X MG RESISTOR 3.9kΩ 1/16W J R112 NRSA63J-470X MG RESISTOR 47Ω...
Page 70
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R711 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R793 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R712 NRSA63J-102X MG RESISTOR 1kΩ...
Page 71
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R3815 NRSA63J-821X MG RESISTOR 820Ω 1/16W J R9203 NRSA63J-242X MG RESISTOR 2.4kΩ 1/16W J R3816 NRSA63J-473X MG RESISTOR 47kΩ...
Page 72
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R9609 NRSA63J-155X MG RESISTOR 1.5MΩ 1/16W J L706 NQL79GM-4R7X COIL 4.7uH M R9610 NRVA63B-562X CMF RESISTOR 5.6kΩ...
Page 73
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D411 NECBB205/WQR/-X R471 NRSA63J-122X MG RESISTOR 1.2kΩ 1/16W J D412 NECBB205/WQR/-X R472 NRSA63J-122X MG RESISTOR 1.2kΩ 1/16W J D413 NECBB205/WQR/-X R473...
Page 74
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local K491 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J C603 NEAF0JM-107X E CAPACITOR 100uF 6.3V M K801 NRSA63J-0R0X MG RESISTOR 0Ω...
Page 75
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R579 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R431 NRSA63J-225X MG RESISTOR 2.2MΩ 1/16W J R580 NRSA63J-101X MG RESISTOR 100Ω...
Page 76
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local R903 NRSA63J-220X MG RESISTOR 22Ω 1/16W J R904 NRSA63J-220X MG RESISTOR 22Ω 1/16W J R905 NRSA63J-220X MG RESISTOR 22Ω 1/16W J R906 NRSA63J-220X MG RESISTOR 22Ω...
Page 78
Packing materials and accessories parts list Block No. No additional / supplemental order of WARRANTY CARDs are available. A1 A3 A8 A9 A4 A5 L 13942296513 A6 A7 KD-SHX850 A2 A4 A5 A6 KD-AR8500 KD-AR8500 only KIT: A10 A11 A12 A13 u163 3-22 http://www.xiaoyu163.com...
Page 79
http://www.xiaoyu163.com 3 7 63 1515 0 Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local LVT1371-001A INST BOOK ENG SPA FRE LVT1355-001B INST BOOK ENG SPA FRE AR8500J LVT1371-002A INSTALL MANUAL LVT0717-001B TROUBLE SHEET(C ------------ WARRANTY CARD BT-51029-2...