Parts List - Koolatron Bite Shield Guardian MK-12 Owner's Manual

Look carefully between all packaging internal dividers for parts.
(A) Trap Body
F
(B) Burner Unit
(C) Support Column
(D) Catch Cup (Shown installed to body)
(E) Base with wheels
(F) Power Supply
Input:120VAC 60Hz, 71W
Ouput:12VAC @4200mA
(G) Regulator with Hose
(attached to burner unit) /
(H) Propane Tank (not included) /
(I) Wheels (attached)
(J) Locking Pin
(K) Octenol Attractant
(L) Bite Shield™ Sticky Paper
L
INSTRUCTIONS FOR OCTENOL MOSQUITO ATTRACTANT
1. Cut foil pack open using scissors. See Illustration A.
2. Remove Octenol cartridge from foil pack.
3. Connect "S" hook to Octenol cartridge. See Illustration B.
4. Connect other side of "S" hook to trap. See Illustration C.
Put larger end of "S" Hook through hole of the Octenol Cartridge
5. Wash hands thoroughly.
6. For best performance, replace lure every 30-60 days.
Please see package for cautions and instructions.
To order more Octenol cartridges please visit a retailer near you or visit us at: www.koolatron.com

PARTS LIST

I
D
H
K
E
J
A
B
C
4
Bite Shield™ Sticky Paper Attachment
INCLUDED FREE TO FURTHER BOOST YOUR CAPTURE RATE OF BLOOD-SEEKING FLYING
A
IMPORTANT! Before removing the masking paper, familiarize yourself with the clips
and sticky paper. Do a test fit of the clips through the slots of the sticky paper so you
are familiar with the feel, flexibility and amount of force that will be required to push
B
the clips through the slots in the sticky paper.
1. Make sure the three (3) clips are properly installed and firmly in place. If they are
G
not pre-installed, follow these instructions:
A. Orient the clip so that the tab with the cross shaped hole is upwards.
C
B. Further, orient the clip so that the snaps (protrusions on the sides of the clip)
face away from your mosquito trap.
C. Slightly pull one of the "legs" of the upper cap outward away from the
mosquito trap body.
D. Place the cross shaped hole onto the 3 bladed peg on the back of the "Leg",
I
then re-insert the peg into the trap's body. Do this for all three clips.
E. Note that only the end and center holes on the Sticky Plastic Sheet are used
on this machine.
2. Place the sticky paper on a clean, flat surface and carefully remove the yellow pro-
tective film from the sticky paper. It may be easier to pull the film off from each end
towards the center. There is a ½ inch strip along the top that has a non-sticky sur-
face for you to hold on to; exercise care to avoid making contact with the sticky
surface to yourself, your clothes or foreign objects to the exposed sticky surface.
3. Holding the sticky paper in the corners, align the first slot in the sticky paper with
the small strap protruding from a clip, push the clip through the slot, fold and snap
into place. Repeat with the other four slots under the rim.
The Sticky Paper will now capture blood seeking flying insects drawn to your trap
without impeding the natural capture technique that deposits flying insects into the
Trap's capture cup – it will only capture those that fly around the trap! Replace as
necessary.
You can re-order additional sticky paper online at www.koolatron.com or by phone at 1-800-265-8456
ITEM CODE: MKSP-3M MOSQUITO TRAP STICKY PAPER 3-PACK - includes 3 pieces of sticky paper
INSECTS!
INSTRUCTIONS
ACCESSORIES
PROPANE TANK COVER
• Made of durable outdoor cotton-based, weather-resistant material
• Machine washable in cold water, looks great!
• Designed with sewn-in velcro strips for quick and easy wrap-around installation
• Fits any standard 9.07kg/20lbs. propane tank
• One year warranty
For prices and availability please call: 800-265-8456