DigiTech nautila Owner's Manual
  1. Manuals
  2. Brands
  3. DigiTech Manuals
  4. Music Pedal
  5. nautila
  6. Owner's manual
DigiTech nautila Owner's Manual

DigiTech nautila Owner's Manual

Chorus-flange
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL

Advertisement

Table of Contents
loading

Related Manuals for DigiTech nautila

Summary of Contents for DigiTech nautila

  • Page 1 OWNER’S MANUAL...

  • Page 2: Warranty

    The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
  • Page 3 To use the Nautila pedal, enable the effect with the FOOTSWITCH (the LED will light when the effect is enabled). Select the desired effect type (chorus or flange) with the toggle switch. Set the MIX control to the 12 o’...

  • Page 4: User Interface

    Connect the specified Harman power supply (sold separately) to this jack. Be sure to use the proper power supply for your area’s mains line voltage. See 'Specifications' on page 9 for power supply model information. The Nautila can only be powered using the external power supply. 3. Drift Knob Varies the shape of the modulation sweep.

  • Page 5: Indicator Led

    The speed of the modulation effect can be altered during performance by pressing and holding the Footswitch while the effect is on. The Nautila’s LED will turn green and the speed will be altered for as long as the FOOTSWITCH is held.

  • Page 6: Making Connections/Applying Power

    To connect the Nautila pedal to your rig: 1. Turn down the amplifier’s master volume control. 2. Make all audio connections to the Nautila as shown in 'Connection Diagrams' on page 5. 3. Connect the appropriate Harman power supply (not included) to the POWER input connector and connect the other end to an available AC outlet.

  • Page 7: Connection Diagrams

    CONNECTION DIAGRAMS Mono/Stereo Amplifier Setup Amp 1 Harman Power Supply IN 1 (MONO) OUT 1 (MONO) IN 2 OUT 2 Amp 2 Other Effects Use only unbalanced TS instrument cables for audio connections. Optional Amplifier Effects Loop Setup Harman FX SND FX RTN Power Supply IN 1 (MONO)

  • Page 8: Example Settings

    EXAMPLE SETTINGS Try these settings to get started. Flange Wash Flange Wash Warm Lush Chorus Warm Lush Chorus Flange Wash Flange Wash Warm Lush Chorus Warm Lush Chorus Bright Vibrato Bright Vibrato Jet Flange Jet Flange Bright Vibrato Bright Vibrato Jet Flange Jet Flange...
  • Page 9 PERFORMANCE ACCESSORIES The performance accessories make integrating the Nautila pedal into any pedalboard a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • StompLock™ (keeps your settings where you want them)
  • Page 10 StompLock™ The included StompLock lets you lock your settings in place, while the open-top design lets you see your settings. To place the StompLock over the pedal knobs: 1. Set the knobs to your preferred settings. 2. Orient the StompLock so that it lines up with the knobs and gently push it over the top of the knobs.

  • Page 11: Specifications

    SPECIFICATIONS Interface Controls: Mix, Drift, Speed, Depth, Emphasis, Voices, Effect Type, Effect On/Off Jacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Inputs Input Impedance: Effect on: >1 MΩ (stereo), >500 kΩ (mono) Effect off: True hardwire bypass Outputs Output Impedance: Effect on: 1 kΩ...
  • Page 12 PHONE: (801) 566-8800 WEB: digitech.com SUPPORT: digitech.com/en-US/support Nautila Owner's Manual 5077393-A © 2016 Harman. All rights reserved. DigiTech is a registered trademark of Harman.

Table of Contents