Table of Contents
Advertisement
KV-AR252M61
RM-W102
3-3. PICTURE QUALITY ADJUSTMENT
SUB COLOR ADJUSTMENT
1. Select Video.
2. Input PAL 100% Color Bar.
3. Set to following condition:
PICTURE 100%,COLOR 50%, BRIGHTNESS 50%,
HUE Center, SHP 50%.
4. Set the PICT 06 WTS to 00h.
5. Connect an oscilloscope to pin 2 (B OUTPUT) of
CN004 A Board.
6. Set the service mode and select SADJ 04 "SCOL"
with
and
of the commander then adjust to VB2 =
1
4
VB3 = VB4 (for PAL) with
data as below:-
- Add 2 steps to SCOL (PAL) - 25" / 29"
- Add 6 steps to SCOL (PAL) - 34"
7. Copy "SCOL 50 PAL(Video)"data to "SCOL 50
SECAM(Video)"
8. Copy "SCOL 50 PAL(Video)" and "SCOL 50 SECAM
(Video)" data to "SCOL 50 PAL(TV)" and "SCOL 50
SECAM(TV)" Table.
9. Input NTSC 75% Color Bar to TV set 3-5.
10. Set the service mode and select SADJ 04 "SCOL"
with
and
of the commander then adjust to VB1 =
1
4
VB4 (for NTSC) with
as below:-
- Add 3 steps to SCOL (NTSC) - 25" / 29"
- Add 6 steps to SCOL (NTSC) - 34"
11. Copy "SCOL 60 NTSC(Video)"data to "SCOL 60
NTSC(TV)"
12. Copy "SCOL 50 PAL"data to "SCOL 50 YUV" table
and "SCOL 60 NTSC" data to "SCOL 60 YUV".
13. Set WTS back to original data.
VB1
VB2 = VB3 = VB4(For PAL sub color adjustment)
VB1 = VB4(For NTSC sub color adjustment)(Difference is
within 70mV)
SUB HUE ADJUSTMENT
1. Select Video.
2. Input NTSC 3.58 Color Bar to TV set.
3. Set to following condition:
PICTURE 100%,COLOR 50%, BRIGHTNESS 50%,
HUE Center, SHP 50%.
4. Connect an oscilloscope to pin 2 (B output) of CN004.
5. Set the service mode and select SADJ 01 "SHUE"
with
and
of the commander then adjust to
1
4
VB1=VB2=VB3=VB4 with
6. Then press [MUTING] t
7. Select TV channel and repeat 3-6.
8. Single systems models with NTSC 4.43 select TV
channel with NTSC 4.43 repeat item 3-6.
and
and write in the
3
6
and
and write in the data
3
6
VB2
VB3
VB4
and
.
3
6
to write the data.
-
VB1
VB2
VB1 = VB2 = VB3 = VB4
The highest level of VB1, VB2, VB3, VB4 must be
aligned at the same time.
The ideal difference between VB2 and VB3 is within ± 80mV.
Sub Hue Adjustment For YUV input
1. Select YUV input.
2. Input NTSC 3.58 Color Bar Into YUV mode.
3. Connect an oscilloscope to pin 1 (B output) of CN004.
4. Set the service mode and select YC 13 "TINT" with
and
of the commander then adjust to
4
VB1=VB2=VB3=VB4 with
5. Then press [MUTING] t
VB1
VB2
VB1 = VB2 = VB3 = VB4
The highest level of VB1, VB2, VB3, VB4 must be
aligned at the same time.
The ideal difference between VB2 and VB3 is within ± 80mV.
PMAX/CONTRAST ADJUSTMENT
Picture Mode: Personal
1. Select Video mode.
2. i)Input PAL Color Bar toTV set. (Other)
ii)Input NTSC 75% Color Bar (NTSC model).
3. Set the following condition:
PICTURE 100%, COLOR 0%,BRIGHTNESS 50%
4. Connect oscilloscope to pin 4 (R Output) of CN004,
5. Set to Service Mode PWL PICT 03 to 00h and WHBL
017 BLBG to 01h.
6. Select SADJ 00 "PMAX" with
commander then adjust VR within spec with
34"
VR
29"
25"
7. Copy SADJ 00 PMAX (Video mode) to SADJ 00
PMAX (TV mode).
8. Select "WIDE" mode for TV & Video mode, Write the
PMAX Data – 6 steps (for model with V-Compression
features only).
9. Set the PWL & BLBG back to (PWL: 01h and BLBG: 00h)
– 30 –
VB3
VB4
80mV
and
.
3
6
to write the data.
-
VB3
VB4
80mV
and
of the
1
4
and
3
VR
Black
PAL
NTSC
2.20±
1.85±0.03Vpp
0.03Vpp
1.90±
1.57±0.03Vpp
0.03Vpp
2.20±
1.85±0.03Vpp
0.03Vpp
1
.
6
Advertisement
Chapters
Table of Contents
Troubleshooting
