Page 1
Operating and installation instructions Ceramic cooktops with induction To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en-AU, NZ M.-Nr. 07 839 980...
Contents Warning and Safety instructions................ 4 Caring for the environment ................ 14 Overview....................... 15 Cooktop......................... 15 KM 6113 ...................... 15 KM 6115 ...................... 16 Controls / Indicators....................17 Cooking zone data ....................19 Using for the first time .................. 20 Cleaning the cooktop for the first time..............
They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for non- compliance with these instructions. Keep these instructions in a safe place and ensure that new users are familiar with the contents.
Page 5
This cooktop is not suitable for outdoor use. It is intended only to cook food and keep it warm. Any other use is not supported by Miele and could be dangerous. This appliance is not intended for use by persons (including...
Page 6
Warning and Safety instructions Safety with children Young children must not be allowed to use this appliance. Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely, recognising the dangers of misuse.
Page 7
Repairs and other work by unqualified persons could be dangerous. Installation, maintenance work and repairs to electrical appliances must only be carried out by a Miele approved service technician. A damaged appliance is dangerous. Check it for any visible damage.
Page 8
The manufacturer's warranty will be invalidated if the appliance is not repaired by a Miele approved service technician. Faulty components must only be replaced by genuine Miele spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used.
Page 9
Warning and Safety instructions If the cooktop is installed behind a furniture panel (e.g. a door), ensure that the door is never closed whilst the cooktop is in use. Heat and moisture can build up behind a closed furniture panel and cause subsequent damage to the cooktop, the housing unit and the floor.
Page 10
Warning and Safety instructions In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings clean at all times. Any damage caused by cockroaches or other vermin will not be covered by the warranty. ...
Page 11
Warning and Safety instructions When the appliance is switched on either deliberately or by mistake, or when there is residual heat present, there is the risk of any metal items left on the cooktop heating up, with the danger of burning.
Page 12
Warning and Safety instructions Pans which boil dry can cause damage to the ceramic glass. Do not leave the cooktop unattended whilst it is being used. Only use pots and pans with smooth bases. Rough bases will scratch the ceramic glass. ...
Warning and Safety instructions Do not use two pans on a cooking zone, extended zone or PowerFlex zone at the same time. If the pan only partially covers the cooking zone, the handle could become very hot. Ensure that you always place the pan in the middle of the cooking zone.
Caring for the environment Disposal of the packing Disposing of your old material appliance The transport and protective packaging Electrical and electronic appliances has been selected from materials which often contain materials which, if are environmentally friendly for handled or disposed of incorrectly, disposal, and can normally be recycled.
Overview Cooktop KM 6113 a Cooking zone with TwinBooster b Cooking zone with Booster c Cooking zone with Booster d Controls / Indicators...
Page 16
Overview KM 6115 a Cooking zone with TwinBooster b Cooking zone with Booster c Cooking zone with Booster d Cooking zone with Booster e Controls / Indicators...
Overview Controls / Indicators Sensor controls a For switching the cooktop on/off b Setting - For setting the power level - For setting the time - For activating/deactivating the system lock/safety lock c For switching on/off the Booster/TwinBooster d For selecting the cooking zone e Timer - For switching on and off - For switching between timer functions...
Overview j For cooking zone selection, e.g. rear right burner k Minute minder l In half hours if the minute minder setting exceeds 99 minutes g Cooking zone display Cooking zone ready for use Keeping warm setting to Power setting ...
Overview Cooking zone data Cooking zone KM 6113 Ø in cm* Rating in watts for 230 V** 18–28 Normal 2600 TwinBooster, level 1 3000 TwinBooster, level 2 3700 14–20 Normal 1850 Booster 3000 10–16 Normal 1400 Booster 2200 Total 7400 * Cookware of any diameter may be used within the specified range.
Using for the first time Please stick the extra data plate for Switching on the cooktop for the appliance supplied with this the first time documentation in the space provided The metal components have a in the "After sales service, data plate, protective coating which may give off a warranty"...
Induction The induction principle When the appliance is switched on either deliberately or by mistake, An induction coil is located under each or when there is residual heat cooking zone. When a cooking zone is present, there is the risk of any metal switched on, this coil creates a items placed on the cooktop (e.g.
Induction Noises When using an induction cooking zone, the following noises can occur in the pan, depending on what it is made of and how it has been constructed. On the higher power settings, it might buzz. This will decrease or cease altogether when the power setting is reduced.
Induction – Lift pans into position on the Pans cooktop. Sliding them into place can Suitable pans: cause scuffs and scratches. – Stainless steel pans with a base that – Often the maximum diameter quoted can be magnetised. by manufacturers refers to the diameter of the top rim of the pot or –...
Tips on saving energy – Use a lid whenever possible to minimise heat loss. – Select a smaller pan when cooking small quantities. A smaller pan uses less energy than a larger pan with very little in it. – Cook with as little water as possible. –...
Power level range The cooktop is programmed with 9 power levels at the factory. If you wish to fine- tune a setting, you can extend the power setting range to 17 power levels (see "Programming"). Settings Default Extended setting settings (9 power (17 power levels)
Operation Operating principles Malfunction due to dirty and/or covered sensors: The glass ceramic cooktop is equipped If the sensors are dirty or covered, with electronic sensor controls which this could cause them to fail to react, react to finger contact. For safety to activate a function or even to reasons, in order to switch the cooktop switch the cooktop off automatically...
Operation Switching off Fire hazard! Do not leave the cooktop unattended To switch a cooking zone off, touch whilst it is being used. the sensor for the required cooking Please note that the heating up time zone twice. on induction cooktops is very much ...
Operation Auto heat-up Continued Heat-up time cooking setting [min : sec] When Auto heat-up has been activated, the cooking zone switches on approx. 0 : 15 automatically at the highest setting and approx. 0 : 15 then switches to the continued cooking setting which you have previously approx.
Operation Cooking zones are networked in pairs Booster to supply the power for the Booster The cooking zones are equipped with a function. When the Booster function is Booster or TwinBooster (see "Overview selected, a proportion of energy is – Cooktop"). You can use the Booster taken away from the linked cooking function for a maximum of two cooking zone and the following happens within...
Page 30
Operation Touch the B I/II sensor repeatedly Switching on the Booster until the indicator light for the Booster Briefly touch the sensor of the goes out and the cooking zone desired cooking zone. setting appears in the display. Select a power setting if necessary. ...
Operation Setting the keeping warm function Keeping warm Briefly touch the sensor of the The keeping warm function is not desired cooking zone. designed to reheat food from the cold state. It is only for keeping food warm Touch the + sensor until appears in directly after cooking.
Timer Minute minder The cooktop has to be switched on if you wish to use the timer. Setting You can set a time between 1 minute () and 9.5 hours (.). Touch the sensor. and the minute minder indicator light The timer can be used for two different will flash in the timer display.
Timer If you want to set another cooking Switching a cooking zone off zone to switch off automatically, automatically follow the same steps as described You can set a time after which the above. cooking zone will switch off automatically.
Timer If you want to show the times remaining Using both timer functions at which are counting down in the the same time background: The minute minder and automatic Touch the timer display repeatedly switch-off functions can be used at the until same time.
Safety features The safety lock is set when the Safety lock / System lock cooktop is switched on. When the The system lock and safety lock are safety lock is activated: deactivated if there is an interruption – The power settings for the cooking to the power supply.
Safety features Power management Safety switch-off The total output of the cooktop can be Safety switch-off with an overlong limited to 3.0 kW in order to match to cooking time the requirements of a local network The safety switch-off mechanism is provider.
If, despite removing the cause, the – The set power level will be reduced. overheating protection mechanism triggers again, contact Miele. – The cooking zone will switch off automatically. The fault code Control panel will appear.
Cleaning and care Clean the entire cooktop after each use. Danger of burning! Allow it to cool down before cleaning. The cooking zones must be switched Dry the appliance after using water to off. The cooktop needs to cool clean it.
Page 39
(spots with a glass-ceramic surface and the frame metallic appearance) can be removed or the frame and the worktop with using the Original Miele ceramic and sharp, pointed objects. stainless steel cooktop cleaner. This could damage the seals.
Programming You can programme certain settings on Calling up programming the cooktop to suit your personal With the cooktop switched off touch needs. Several settings can be changed the and B I/II sensors at the same in succession. time until the Booster indicator light After accessing programming mode, ...
Page 41
Programming Settings Programme Status Demonstration Demonstration mode on mode and factory Demonstration mode off default settings Factory default settings reinstated Number of power 9 power settings settings 17 power settings Induction warning tone when there is Quiet no pan or the pan is unsuitable Medium Loud...
Page 42
Programming Settings Programme Status Power management Audible tone if the sensors are covered Sensor switch Slow reaction speed Standard Fast Programmes not shown here have no allocation. The factory setting is shown in bold. After the cooktop has been switched on, will appear in the front left cooking zone display and ...
Programming Reset This function allows you to quickly reset all the programming settings back to their original factory default settings. Initiating reset Switch the cooktop on. Touch the sensors for selecting the front left and front right cooking zones at the same time until the cooking zone displays go out (approx.
Problem solving guide With the aid of the following guide, minor problems can be easily corrected without contacting Miele. If, after reading this guide, you can't remedy the problem yourself, please call Miele (see back cover for details). Please note, however, that a call-out charge will be applied to unnecessary service visits where the problem could have been rectified as described in these operating instructions.
Page 45
Problem solving guide Problem Possible cause and remedy After switching on the The system lock or safety lock is activated. cooktop, appears in Deactivate the system lock or safety lock (see the front left cooking "System lock / Safety lock"). zone display and ...
Page 46
Interrupt the power supply to the cooktop for approx. 1 minute. If the problem persists after power is restored, please contact Miele. The cooktop switches One or several of the sensors are covered, for off and flashes in the example, by finger contact, food boiling over or by an cooking zone displays.
Page 47
Make sure it has not been blocked by something like a fork. Remove the cause of the blockage. If this fault message continues to appear in the display, contact Miele. and other numbers There is a fault in the electronic module.
250 ml appliance. These can be ordered online at: Removes heavy soiling, limescale deposits and aluminium residues. or from Miele (see end of this booklet Original Miele all purpose microfibre for contact details). cloth Saucepans and frying pans Miele offer a wide range of pans which are perfect for Miele cooktops.
Safety instructions for installation The appliance must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations. Fit the wall units and rangehood before fitting the cooktop to avoid damaging the cooktop.
Safety distances Safety distance above the cooktop A minimum safety distance must be maintained between the cooktop and the rangehood above it. See the rangehood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the rangehood, a minimum safety distance of 600 mm must be maintained.
Page 51
Safety distances Safety distances to the sides Minimum safety distances and back of the cooktop underneath the cooktop Ideally the cooktop should be installed To ensure sufficient ventilation to the with plenty of space on either side. cooktop, a certain gap must be left There may be a wall at the rear or a tall between the underside of the cooktop unit or wall on one side (right or left),...
Installation notes Seal between the cooktop and Tiled worktop the worktop Grout lines and the hatched area underneath the cooktop frame must be smooth and even. If they are not, the Do not use sealant between the cooktop will not sit flush with the cooktop and the worktop.
Building-in dimensions KM 6113 a Front b Installation height c Mains connection box The mains connection cable (1440 mm long) is supplied separately with the cooktop.
Page 54
Building-in dimensions KM 6115 a Front b Installation height c Mains connection box The mains connection cable (1440 mm long) is supplied separately with the cooktop.
Installation Preparing the worktop Installing the cooktop Make the worktop cut-out as shown Feed the mains connection cable in "Building-in dimensions". Observe down through the cut-out. the safety distances (see "Safety Place the cooktop centrally in the distances").
AC 230 V, 50 Hz repair work is dangerous to users. The voltage and rated load are given on Miele cannot be held liable for the data plate. Please ensure these damage or injury caused by incorrect match the household mains supply.
If the mains cable needs to be replaced, it must be replaced with a special connection cable, type H 05 VV-F (PVC insulated), available from Miele. The connection data is given on the data plate. Wiring diagram a b c d e...
After sales service, data plate, warranty After sales service In the event of any faults which you cannot easily remedy, please contact Miele. See back of this booklet for contact details. Please quote the model and serial number of your appliance when contacting Miele.
Page 59
Freemans Bay, Auckland 1011 Miele Experience Centre South Melbourne: 206-210 Coventry Street Miele Experience Centre South Melbourne, VIC 3205 Auckland: Miele Experience Centre and Office Sydney: 8 College Hill 3 Skyline Place Freemans Bay, Auckland 1011 Frenchs Forest, NSW 2086 Telephone:...
Page 60
KM 6113 / KM 6115 en-AU, NZ M.-Nr. 07 839 980 / 08...