Picture Options - Samsung PS50B550 User Manual

White Balance
„
You can adjust the colour temperature for more natural picture colours.
R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain
•
• Reset : The previously adjusted white balance will be reset to the factory defaults.
Flesh Tone
„
You can adjust the flesh tone to be more or less red.
Changing the adjustment value will refresh the adjusted screen.
N
Edge Enhancement →
„
You can emphasize object boundaries in the picture.
xvYCC → Off / On
„
Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).
xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.
N
This function may not be supported depending on your external device.
N

Picture Options

❑
You can customize the additional picture settings to suit your preference.
In PC mode, you can only make changes to the Colour Tone, Size and Screen
N
Burn Protection from among the items in Picture Options.
Colour Tone → Cool / Normal / Warm1 / Warm2 / Warm3
„
You can select the most comfortable colour tone to your eyes.
The adjusted values are stored according to the selected Picture mode.
N
Warm1 , Warm2, or Warm3 is only activated when the picture mode is Movie.
N
Size
„
You can select the picture size which best corresponds to your viewing requirements.
• 16:9 : Sets the picture to the 16:9 aspect ratio.
• Wide Zoom : Magnify the size of the picture more than 4:3.
• Zoom : Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.
• 4:3 : Sets the picture to the 4:3 aspect ration.
• Screen Fit: Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p) or Component
(1080i/1080p) signals are input.
The picture size options may vary depending on the input source.
N
The items available may differ depending on the selected mode.
N
In PC Mode, only 16:9 and 4:3 mode can be adjusted.
N
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N
Temporary image retention may occur when viewing a static image on the set for more than two hours.
N
After selecting Wide Zoom mode: Press the ► button to select Position, then press the ENTER E button.
N
Press the ▲ or ▼ button to move the screen up / down. Then press the ENTER E button.
After selecting Zoom mode: Press the ► button to select Position, then press the ENTER E button. Press the ▲ or ▼
N
button to move the picture up and down. Then press the ENTER E button. Press the ► button to select Size, then press
the ENTER E button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the
ENTER E button.
After selecting Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing
N
the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.
Reset : Press the ◄ or ► button to select Reset, then press the ENTER E button. You can initialize the setting.
N
If you use the Screen Fit function with HDMI 720p input, 1 line will be cut at the
N
top, bottom, left and right as in the overscan function.
You can select these options simply by pressing the
O
control.
Digital NR → Off / Low / Medium / High / Auto
„
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static
and ghosting that may appear on the screen.
When the signal is weak, select one of the other options until the best picture is displayed.
N
Off / On
: Changing the adjustment value will refresh the adjusted screen.
P.SIZE button on the remote
English - 16
Tint (G/R) : G50/R50
Advanced Setting
Picture Options
Picture Reset
Continued...
►