Setting The Bnc Connectors; Setting The Rgb1 Connector; Setting A Computer Image To The Correct Rgb Select Screen - NEC PlasmaSync 50XM3 Model Information
Hide thumbs
Also See for PlasmaSync 50XM3:
- Installation manual (10 pages) ,
- Operation manual (8 pages) ,
- Supplementary manual (28 pages)
Table of Contents
Advertisement
"V"
OPTION1
OSM
BNC INPUT
:
RGB
D-SUB INPUT
:
RGB
RGB SELECT
:
AUTO
HD SELECT
:
1080B
INPUT SKIP
:
OFF
ALL RESET
:
OFF
1024 768
SEL.
MENU/ENTER
OK
EXIT
RETURN
OSM ORBITER settings
ON ........ The position of the menu will be shifted by
eight dots each time OSM is displayed.
OFF ...... OSM will be displayed at the same position.
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults except for Auto Picture.
Setting the BNC connectors
Select whether to set the input of the 5 BNC connectors to
RGB, component or SCART1,2.
Example: Set the BNC INPUT mode to "COMP."
1. On the MAIN MENU, select "OPTION1", then press
the MENU/ENTER button.
The "OPTION1" screen appears.
2. Use the
and
buttons to select "BNC INPUT".
3. To set the BNC INPUT mode to "COMP."...
Use the
and
buttons to select "COMP.".
The mode switches as follows each time the
button is pressed:
→RGB ↔ COMP. ↔ SCART1 ↔ SCART2←
OPTION1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL.
ADJ.
Information
BNC INPUT Settings
RGB ............ Use the 5BNC terminals for RGB input.
COMP. ......... Use the 3BNC terminals for component input.
SCART1 ...... Use the 4BNC terminals for RGB with
composite sync. See page E-8.
SCART2 ...... Use the 3BNC terminals for RGB and the
VIDEO1 terminal for composite sync. See
page E-8.
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory defaults.
or
1 / 3
:
COMP.
:
RGB
:
AUTO
:
1080B
:
OFF
:
OFF
EXIT
RETURN
E-25
3-94
Setting the RGB1 connector
Select one of the signals being transmitted to the RGB1
terminal.
Example: Set the D-SUB INPUT mode to "SCART3"
1. On the MAIN MENU, select "OPTION1", then press
the MENU/ENTER button.
The "OPTION1" screen appears.
2. Use the
and
buttons to select "D-SUB INPUT".
3. To set the D-SUB INPUT mode to "SCART3"...
Use the
and
buttons to select "SCART3".
The mode switches as follows each time the
button is pressed:
RGB ↔ SCART3
OPTION1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL.
ADJ.
Information
D-SUB INPUT Settings
RGB ................ Use the D-SUB terminal for RGB
input.
SCART3 .......... Use the D-SUB terminal for RGB
signal fed from SCART. See page E-8.
Setting a computer image to the correct RGB
select screen
With the computer image, select the RGB Select mode
for a moving image such as (video) mode, wide mode or
digital broadcast.
Example: Setting the "RGB SELECT" mode to
"MOTION "
1. On the MAIN MENU, select "OPTION1", then press
the MENU/ENTER button.
The "OPTION1" screen appears.
2. Use the
and
buttons to select "RGB SELECT".
3. To set the RGB select mode to "MOTION" ...
Use the
and
buttons to select "MOTION".
The mode switches as follows each time the
button is pressed:
→ AUTO ↔ STILL ↔ MOTION ↔ WIDE1 ↔ WIDE2 ↔ DTV ←
OPTION1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL.
ADJ.
CONFIDENTIAL
or
1 / 3
:
RGB
:
SCART3
:
AUTO
:
1080B
:
OFF
:
OFF
EXIT
RETURN
or
1 / 3
:
RGB
:
RGB
:
MOTION
:
1080B
:
OFF
:
OFF
EXIT
RETURN
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
