1. Manuals
  2. Brands
  3. Nokia Manuals
  4. Headsets
  5. HS 3W
  6. User manual

Nokia HS 3W User Manual

Wireless clip-on headset
Hide thumbs Also See for HS 3W:
Table of Contents

Advertisement

Quick Links

See also: User Manual
User's Guide for the Wireless
Clip-on Headset (HS-3W)
9356820
Issue 2

Advertisement

Table of Contents
loading

Related Manuals for Nokia HS 3W

Summary of Contents for Nokia HS 3W

  • Page 1 User’s Guide for the Wireless Clip-on Headset (HS-3W) 9356820 Issue 2...
  • Page 2 Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.

  • Page 3: Table Of Contents

    Contents 1. Introduction ... 4 Bluetooth wireless technology ... 4 The card in the sales package... 5 2. Getting started... 6 Overview ... 6 Chargers and batteries... 7 Removing and installing the battery 8 Charging the battery ... 9 When the battery charge falls low...

  • Page 4: Introduction

    ■ Bluetooth wireless technology The Wireless Clip-on Headset HS-3W is specially designed for compatible Nokia phones that support Bluetooth technology. The headset can, however, be used with any compatible Bluetooth devices that support the Handsfree or Headset profiles. (Profile is a set of Bluetooth commands that the phone uses to control the headset).

  • Page 5: The Card In The Sales Package

    I n t r o d u c t i o n ■ The card in the sales package The card contains the general Bluetooth passcode (0000) that you need to pair the phone with the headset. Keep this card in a secure place, see Pairing the headset with a compatible phone on page 9.

  • Page 6: Getting Started

    2. Getting started Note: The use of wireless devices may be restricted in some situations. Observe any restrictions and obey all signs and instructions concerning use of wireless devices. ■ Overview The headset contains the following parts, as shown in Figure 1. Note: Parts of the headset are magnetic.

  • Page 7: Chargers And Batteries

    The Wireless Clip-on Headset HS-3W is intended for use with the following chargers: ACP-8, ACP-9, ACP-12 and LCH-12. Warning! Use only batteries and chargers approved by Nokia for use with this particular enhancement. The use of any other types will invalidate any approval or warranty applying to the enhancement, and may be dangerous.

  • Page 8: Removing And Installing The Battery

    ■ Removing and installing the battery Note: Before changing the cover, always switch off the power and disconnect the device from the charger. Always store and use the device with the covers attached. The headset has a rechargeable Li-Polymer battery. •...

  • Page 9: Charging The Battery

    4. Set the phone to search for Bluetooth devices as instructed in the user’s guide of the phone. 5. Select the Nokia HS-3W from the list. G e t t i n g s t a r t e d...

  • Page 10: Disconnecting The Headset From The Phone

    6. Enter the passcode to associate ("pair") and connect the headset to the phone. The passcode is marked on the card that is provided in the sales package of the headset. Once you have entered the passcode, the phone becomes the default phone for the headset, if the headset has not been previously paired with another phone.

  • Page 11: Troubleshooting

    Note that switching on the headset creates the connection automatically only if you have set the phone to accept Bluetooth connection requests without your permission. In compatible Nokia phones this can be done by changing your paired devices settings in the Bluetooth menu.

  • Page 12: Using The Headset

    3. Using the headset Note: The use of wireless devices may be restricted in some situations. Observe any restrictions and obey all signs and instructions concerning use of wireless devices. ■ Switching the headset on or off To switch on the headset, press and hold the power key for 2 seconds. The headset beeps and the green indicator light starts blinking.

  • Page 13: Call Functions

    U s i n g t h e h e a d s e t When you don’t use the headset, you can wind the earphone wire around the headset as shown in Figure 6. ■ Call functions When the headset is connected to the phone, make a call by using the phone in the normal way.

  • Page 14: Automatic Answer

    U s i n g t h e h e a d s e t Automatic answer If, on the phone, the Automatic answer function is set to on, the phone automatically answers the incoming call after one ring. Rejecting a call When you receive an incoming call and you do not want to answer, briefly press the answer/end key twice.

  • Page 15: Switching The Call Between Phone And Headset

    U s i n g t h e h e a d s e t ■ Switching the call between phone and headset You can switch the active call between the headset and all compatible phones. To switch the call from the headset to the phone and vice versa, press and hold the answer/end key or use the respective function in your phone.

  • Page 16: Resetting The Headset

    U s i n g t h e h e a d s e t ■ Resetting the headset You can reset the headset to its original settings, for example, to change the default user of the headset. Resetting the headset clears all of its settings, including pairing information.

  • Page 17: Battery Information

    B a t t e r y i n f o r m a t i o n 4. Battery information Your headset is powered by a rechargeable battery. Take good care of the battery and follow the guidelines below. ■...

  • Page 18: Care And Maintenance

    Care and maintenance Your headset is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep all accessories out of the reach of small children. •...

Table of Contents