Note For Repair - Sony DSC-T99 Service Manual

Hide thumbs Also See for DSC-T99:
Table of Contents

Advertisement

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at
the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don't pull at wire of connector. It is possible that
a wire is snapped.
• When installing a connector, don't press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the capacitor
is handled by hand. The electric shock is caused by the charged voltage
which is kept without discharging when the main power of the unit is
simply turned off. Therefore, the remaining voltage must be discharged
as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a resistor
of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent elec-
trical shock.
1 kΩ/1 W
Wrap insulating tape.
DSC-T99/T99C/T99D/T99DC_L2
– ENGLISH –
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 kΩ/1 W
(Part code: 1-215-869-11)1 k
ST-237 Flexible
Board
C901
2-2
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,折れ等がな
いことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しにならないように
注意する。
• コネクタを取り外す時に,線材部 (極細) を持って引っ張ると断線する恐
れがありますので,絶対に線材部 (極細) を持って引っ張らないでくださ
い。
• 線材部 (極細) を押さえながらコネクタを差し込むと,線材部 (極細) が断
線する恐れがありますので,絶対に線材部 (極細) には負担をかけないで
ください。
• 金メッキされているフレキシブル基板には,強い負担をかけないでくだ
さい。
ストロボ用充電コンデンサ (C901) の放電
ストロボ用充電コンデンサは最大315Vの電圧で充電されていま
す。
この高電圧で充電されたコンデンサに手を触れた場合, 電気ショッ
クを受けます。この高電圧には単にセットの電源を切っただけで
は放電されず,残留しています。このため,下記の方法で残留電
圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗 (1-215-869-11) の両端に小型のク
リップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けないように
してください。
1 kΩ/1 W
– JAPANESE –
R:1 kΩ/1 W
(Part code: 1-215-869-11)1 k
ST-237 Flexible
Board
C901

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dsc-t99cDsc-t99dDsc-t99dc

Table of Contents