World Time Mode; To Turn Auto Receive On And Off - Casio QW1382 General Manual

About Auto Receive
When auto receive is turned on, the watch automatically starts to receive the
time calibration signal when the digital time in the Timekeeping Mode reaches
2:00 AM and 4:00 AM each day (calibration times).
• The Auto Receive operation is performed only if the watch is in the
Timekeeping Mode or World Time Mode when one of the calibration times
is reached. It is not performed if the time is reached while you are making
settings (while settings are flashing on the display).
• Auto receipt of the calibration signal is designed to be performed early in
the morning, while you sleep (provided that the digital time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put
it in a location where it can easily receive the signal.
• The receive indicator (
) indicates that at both or at least one of the last
calibration time receipt attempts were successful.
• When auto receive is turned on, the watch receives the calibration signal for
8 to 15 minutes each day when the digital time reaches 2:00 AM and 4:00
AM. Do not operate any of the watch's buttons within 15 minutes prior to or
following the calibration times. Doing so can interfere with correct
calibration.
• Remember that receipt of the calibration signal depends on the time shown
on the digital display. The receive operation will be performed whenever the
digital display shows 2:00 AM and 4:00 AM, regardless of whether or not
that is actually the correct time.
• When both receipts are successful, the watch uses the data of the second
receipt for calibration. When only one receipt is successful, the watch uses
the data of the successful receipt.

To turn auto receive on and off

1. Press B while in the Timekeeping Mode. The current Auto Receive on/off
setting flashes on the display because it is selected .
• The receive indicator flashes along with the current on (
setting.
2. Press D to toggle Auto Receive on and off.
3. Press B to return to the Timekeeping Mode.
Last signal receipt display
In the Timekeeping Mode, press A to display
the date and time of the last successful receipt.
• The last receipt data remains on the display
A
L
for about one or two minutes or until you
press A again to return to the Timekeeping
B
Mode.
C D
TELEMEMO MODE
Number of telememo
items stored
Mode indicator
Remaining
memory
Name
A
L
B
C
D
Telephone number
To input new Telememo data
1. In the Telememo Mode, press A or D
Text area
until the new data display appears.
Cursor
• The new data display is the one that is blank
L A
(contains no name and telephone number).
• If there is no Telememo data stored in
B memory yet, the new data display appears
as soon as you enter the Telememo Mode.
C D 2. Press B and a cursor appears in the text
area.
3. Use A and D to change the character at
Number area
the cursor position in the text area. The
[New Data Display]
character changes in the following
sequence.
Press D
A to Z
(space)
l
:
• Holding down either button changes the character at high speed.
4. When the character you want is at the cursor position, press C to move
the cursor to the right.
5. Repeat the steps 3 and 4 until your text is complete.
• You can input up to eight characters in the text area.
ON ) /off ( OFF
The Telememo Mode lets you store up
to 30 pairs of name and telephone
number data. Data is automatically
sorted based on the characters of the
name. You can recall data by scrolling
through it on the display.
• See the "Character List" at the back
of this manual for details on how the
watch sorts data.
• The data item on the display when
you exit the Telememo Mode
appears first the next time you enter
the Telememo Mode.
• If you do not operate any button for a
few minutes while in the Telememo
Mode, the watch automatically goes
back to the Timekeeping Mode.
Press A
0 to 9 -
/ .
6. After you input a name, use C to move the cursor to the number area.
• The text area can hold up to eight characters. When the cursor is located at
the eighth space of the text area, moving the cursor to the right causes it to
jump down to the first digit in the number area. When the cursor is at the
12th digit of the number area, moving it to the right causes it to jump back
up to the first character of the text area.
7. Use A and D to change the character (hyphen, number, or space) at the
cursor position in the number area. The character changes in the following
sequence.
Press D
Press A
• Holding down either button changes the character at high speed.
8. When the character you want is at the cursor position, press C to move
the cursor to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits in the number area.
10. After inputting your data, press B to store it.
• At this time, the cursor appears in the text area, ready for input of a new
Telememo data item. Note, however, that if the last data item saved
resulted in the memory becoming full, pressing B returns to the Telememo
Mode data screen instead.
11. Input more data (starting from step 3 above) or press B again to return to
the Telememo Mode data screen (without the cursor).
• When you press B, the message
seconds. After the sort operation is complete, the watch returns to the
Telememo Mode data screen (without the cursor).
• The text area of the display can show only five characters at a time, so
longer text scrolls continuously from right to left.
)
Text area
• If the message
{ FULL
that memory is full. To store more data, you will first have to delete some of
the data stored in memory.
• If you do not perform any button operation for a few minutes while the
cursor is on the display, the watch automatically returns to the Telememo
Mode data screen (without the cursor).
To recall Telememo data
In the Telememo Mode, press D to scroll forward through stored data items
or A to scroll in reverse.
• Holding down either button scrolls through the data at high speed.
To edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one
you want to edit.
2. Press B and the first character of the text area starts to flash.
3. Use C to move the flashing to the character you want to change.
4. Use A and D to change the character.
• For details on inputting characters, see "To input new Telememo data"
(steps 3 for name input and 7 for number).
5. After making the changes that you want, press B to store them and return
to the Telememo Mode data screen.
To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one
you want to delete.
2. Press B and the first character of the text area starts to flash.
3. Press A and D at the same time to delete the data item.
• At this time the cursor appears in the text area, ready for input.
4. Input data or press B to return to the Telememo Mode data screen.
Mode indicator
P
L
City code
B
P
C
Current time in the selected city
0 to 9
(space)
SORT appears on the display for a few
Continuously scrolls
Separator (inserted automatically)
Last letter of text
appears in the text area of the display, it means

WORLD TIME MODE

The World Time Mode shows the cur-
rent time in 29 time zones around the
world.
• For full information on city codes,
see the "City Code Table" at the
back of this manual.
• The GMT differential is the time
difference of the time zone where the
GMT
city code is located from Greenwich
differential
Mean Time.
• The GMT differentials used by this
A
watch are based on Universal Time
Coordinated (UTC) data.
• The seconds count of the World Time
is synchronized with the seconds
D count in the Timekeeping Mode.
• The time zone that is displayed
when you leave the World Time
Mode will still be displayed when you
enter the World Time Mode again.
1382-3