Casio QW1382 General Manual

Module No. 1382
• Press C to change from mode to mode. After you perform an operation in
any mode, pressing C returns to the Timekeeping Mode.
Timekeeping Mode
L
B
P
C
Hand Setting Mode
P
TIMEKEEPING MODE
In addition to time and date settings, the Timekeeping Mode also lets you
adjust the contrast of the digital display.
• The Timekeeping Mode is actually made up to four sub-modes. Press D to
switch between the sub-modes.
Time/Date
Month-Date
Day of week
L A
B
P
C
D
Seconds
PM indicator
Hour : Minutes
Date
• This watch displays text for the day of the week in any one of the five
different languages (English, German, French, Italian, and Spanish).
• See the "Day of the Week List" at the back of this manual for information on
abbreviations used.
About Manual Time Setting and Time Calibration
Signal Reception
The current time for this watch can be set by inputting the time and date you
want (manual setting) or by a time calibration signal. Note that the time
calibration signal is available only in certain areas in Europe. For details on
time calibration reception and the areas in which the time calibration signal is
available, see the section of this manual titled: "TIME CALIBRATION SIG-
NAL RECEPTION."
To set the current time manually
A
L
B
P
C D
Receive indicator
Auto
DST Language
Receive
CNT Date
• The Auto Receive, DST, and GMT differential settings are used for time
calibration signal reception only. For details on these settings, see the
section of this manual titled: "TIME CALIBRATION SIGNAL RECEPTION."
• See the section of this manual titled "To adjust the display contrast" for
details on using the CNT (contrast) setting.
A
Press C
D
Analog
Seconds
1. Press B while in the Timekeeping Mode.
The current Auto Receive on/off setting
flashes on the display because it is selected .
• The receive indicator also flashes along with
ON OFF
the current on ( ) /off (
2. Press C to change the selection in the
following sequence.
GMT 12/24-Hour
differential format
Month Year Minutes

GENERAL GUIDE

• Press L in any mode to illuminate the display for about two seconds.
Language indicator
L
B
P
C
Press D
ENG
(English)
Press A
5. Press C until the 12/24-hour indicator is flashing on the display.
•
12H indicates 12-hour format, while
6. Press D to toggle between the 12-hour (
• With the 12-hour format, the P (PM) indicator appears to the left of the
digital time for times in the range of noon to 11:59 pm. Times from midnight
to 11:59 am are shown without any indicator.
• With the 24-hour format, times are indicated in the range of 00:00 to 23:59,
with a 24 indicator to the left of the digital time.
7. Press C until the seconds digits are flashing on the display.
8. Press D to reset the seconds to
• If you press D while the seconds count is in the range of 30 to 59, the
seconds are reset to
count is 00 to 29, the minutes count is unchanged.
9. Press C until the hour digits are flashing on the display.
10. Press D to increase the setting or A to decrease it. Holding down either
button changes the setting at high speed.
11. Repeat steps 9 and 10 to set the minutes, year, month, and date.
12. After you make the settings you want, press B to return to the
Timekeeping Mode.
• When you use the above procedure to set the digital display time, the hands
of the analog timepiece normally adjust according to your setting. If, for any
reason, the digital time does not match the analog time, use the procedure
described under "HAND SETTING MODE" to match the analog setting with
the digital display.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is
flashing, the flashing stops and the watch goes back to the Timekeeping
Mode automatically.
To adjust the display contrast
) setting.
CNT indicator
L
Seconds
B
P
C
Hour
3. Use D to increase the contrast value and A to decrease it.
4. After you make the setting you want, press B to return to the Timekeeping
Mode.
Telememo Mode
Stopwatch Mode
3. Press C until the language indicator is
flashing on the display.
• The language indicator shows the language
A
currently set for the day of the week.
• The day of the week is set automatically in
accordance with the date.
4. Use A and D to change the language
D
setting in the following sequence.
DEUT. FRA
(German) (French)
24H
12H
00 .
00 and 1 is added to the minutes. If the seconds
1. Press B while in the Timekeeping Mode.
The current Auto Receive on/off setting
flashes on the display because it is selected .
A
2. Press C 11 times until the
indicator is flashing on the display.
• The value to the right of the
shows the current contrast setting. You can
D
set the contrast to a value from 1 (lightest) to
7 (darkest).
1382-1
World Time Mode
P
Alarm Mode
ITA ESP
(Italian) (Spanish)
indicates 24-hour format.
24H
) and 24-hour ( ) formats.
CNT
(contrast)
CNT indicator