DeWalt DW682K Manual page 20

E N G L I S H
11 Do not overreach
Keep proper footing and balance at all times.
12 Avoid unintentional starting
Do not carry the plugged-in tool with a finger on the switch.
Be sure that the switch is released when plugging in.
13 Stay alert
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired.
14 Disconnect tool
Shut off power and wait for the tool to come to a complete standstill
before leaving it unattended. Unplug the tool when not in use,
before servicing or changing accessories.
15 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the
tool before operating the tool.
16 Use appropriate tool
The intended use is described in this instruction manual. Do not force
small tools or attachments to do the job of a heavy-duty tool. The tool
will do the job better and safer at the rate for which it was intended.
Warning! The use of any accessory or attachment or performance of
any operation with this tool, other than those recommended in this
instruction manual may present a risk of personal injury.
17 Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the socket.
Keep the cord away from heat, oil and sharp edges.
18 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Inspect the tool cords at regular intervals and,
if damaged, have them repaired by an authorized D
agent. Inspect the extension cords periodically and replace them if
damaged. Keep all controls dry, clean and free from oil and grease.
19 Check for damaged parts
Before using the tool, carefully check it for damage to ensure that it will
operate properly and perform its intended function. Check for
misalignment and seizure of moving parts, breakage of parts and any
other conditions that may affect its operation. Have damaged guards
or other defective parts repaired or replaced as instructed.
Do not use the tool if the switch is defective. Have the switch replaced
by an authorized D WALT repair agent.
E
20 Have your tool repaired by an authorized D
This Power Tool is in accordance with the relevant safety regulations.
To avoid danger, electric appliances must only be repaired by qualified
technicians.
Additional safety rules for biscuit jointers
Plugging into the mains, switching ON and OFF
• Always ensure that the power tool is switched OFF before plugging into
the mains.
• Do not switch OFF before the blade is running freely.
When cutting
• Remove all nails and metal objects from the workpiece before starting
work.
• After switching OFF, never attempt to stop the blade by pressing
against the side of the blade.
• Never put the tool down on a table or workbench unless switched OFF.
Operational protection devices
• The tool must only be used for cutting wood or plastic.
• Ensure that all devices screening the blade are in perfect working order.
en - 2
Checking and changing the blade
Guard against kickback
Package contents
The package contains:
WALT repair
E
Description (fig. A)
Your D
dowel joints in wood and wood products.
WALT repair agent
E
10 Spindle lock
11 Star knob
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Only blades conforming to the specifications contained in these
operating instructions may be used.
• Blades made of high alloy, high speed steel (HSS steel) should not be
used. Best results are achieved using carbide-tipped or CrV blades.
• Only sharp blades in perfect working order should be used; cracked or
bent blades should be discarded and replaced at once.
• Ensure that the blade is securely fixed and rotates in the correct direction.
• Kickback occurs when the tool begins to stall rapidly and is driven
back towards the operator. Release the switch immediately if the blade
sticks or the tool stalls.
• Keep the blades sharp.
• Support large panels near the cutting area.
• Do not remove the tool from the workpiece while making a cut with the
blade rotating. Release the ON/OFF-switch and wait for the blade to
come to a halt.
1 Biscuit jointer
1 Dust bag
2 Dust adapters
1 Pin spanner
1 Torx screwdriver
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
WALT biscuit jointer DW682K has been designed for making flat
E
1 ON/OFF-switch
2 Lock-on button
3 Top handle
4 Fence height adjuster
5 Dust extraction outlet
6 Adjustable fence
7 Anti-slipping pins
8 Plunge depth adjusting knob
9 Locking knob
Your D WALT tool is double insulated in accordance with
E
EN 50144; therefore no earth wire is required.
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
12