Clutch Pedal; Adjustment - Acura 1994 Integra Service Manual

Adjustment
N O T E :
a To check the clutch interlock switch and clutch
switch, see seclion 23.
a The clutch is selt-adjusting to compensate for wear.
CAUTION: It there is no clearanco between the mastel
cylinder piston and push lod. the releaso boaring is held
againsl the diaphragm spring, which can result in clutch
slippage 01 othel clutch problems.
Loosen locknut A, and back otf the clutch switch
{or adjusting bolt) until it no longer touches the clutch
p e d a l .
Loosen locknut C, and turn the push rod in or out
to get the specified stroke (@) and height (O) at the
clutch pedal.
Tighten locknut C.
Turn the clutch switch (or adjusting bolt) until it con-
tacts the clutch pedal.
Turn the clutch switch (or adjusting bolt) in 3/4 to
1 full turn further.
Tighten locknur A.
7. Loosen locknut B and the clutch interlock switch.
8. Measure the clearance between the tloor board and
clutch pedal with the clutch pedal tully depressed.
9 . R e l e a s e t h e c l u t c h p e d a l 1 5 - 2 0 m m { O . 5 9 - O . 7 9
in) from the fully depressed position and hold it there.
Adiust the position of the clutch interlock switch so
that the engine will start with the clutch pedal in this
oosition.
1 0. Turn clutch interlock switch 3/4 to 1 tull turn funher.
1 1 . T i g h t e n l o c k n u t B .
LOCKNUT B
9.8 N.m (1.0 kgf.m, 7 lbf.ftl
CLUTCH INTERLOCK
swtrcH
6 .
1 .
2 .
ASSIST SPRING
-6ll
LOCKNUT C
l3 N.m l'l.3 kgf.m, 9
CLUTCH SWITCH
{or AOJUSTING BOLTI
LOCKNUT A
9.8 {N.ml (1.0 kgl.m, 7 lbt.ftl
(STROKE at PEDALI: 130-140 mm 15.12-5.51 in)
{TOTAL CLUTCH PEDAL FREE PLAY): 12-21 mm 10.47-0.83 inl including tho p.dal play I -lO mm 10.04-0.39 inl
{CLUTCH PEDAL HEIGHTI: 164 mm (6.46 in} to tho lloot
{CLUTCH PEDAL DISENGAGEMENT HEIGHTI: 83 mm 13.27 inl minimum to tho lloo.
PUSH ROD
CLUTCH MASTER CYLINDER
Clutch Pedal
ctutch Pedat
I
[-],ll'"-"" f
| :;i:'":fff*tr#:?iff:".,*::,::".
| .#::J:::
sb''''""
| |
| "orr,O", It there is no clearanco between the master
|
,. aoo""n locknut B and the clutch intertoct switcl.
| |
cylinder piston and push lod. the releaso boaring is held
| | I
against the diaphragm spring, which can result in clutch
|
8. Measure tne clearance between the floor board and
I I
slippage 01 othel clutch problems.
I
clutch pedal with the clutch pedal tully deeressed.
I I
1. Loosen locknut A, and back otf the clutch switch
|
9. Release the clutch pedal 15-2O mm (O.59-O.79
I I
{or adiusting boltl until it no longer touches the clutch
I
int trom ttre fully depressed position and hold it there.
I I
, ::":"" rocknut
c, and rurn the push rod in or out |
iliiiliffi:l1l:J"'1"-:H"l:tJ:i"i#fT: I I
. il*:*j':"'-(@)andheisht(olatthe
|
,:.;:,nterrockswitch3/4torrurrturnturtner.
I tf
,
:: ***r**''
.,".,u"**;
|
'-"'"'';*1,,0*
I I