Table of Contents
Advertisement
Available languages
Available languages
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.
Lubrication
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before lubricating the saw chain.
Fig.13
Lubricate the saw chain and bar using biologically
degradable saw chain oil with an adhesion agent. The
adhesion agent in the saw chain oil prevents the oil from
being thrown off the saw excessively quickly. Mineral
oils must not be used, as they are harmful to the
environment.
CAUTION:
Prevent the oil from coming into contact with the
•
skin and eyes. Contact with the eyes causes
irritation. In the event of eye contact, flush the
affected eye immediately with clear water, then
consult a doctor at once.
Never
use
waste
•
carcinogenic substances. The contaminants in
waste oil cause accelerated wear of the oil pump,
the bar and the chain. Waste oil is harmful to the
environment.
When filling the chain saw with chain oil for the
•
first time, or refilling the tank after it has been
completely emptied, add oil up to the bottom edge
of the filler neck. The oil delivery may otherwise be
impaired.
Fig.14
To fill the oil, perform the following steps:
1.
Clean the area around the oil filler cap thoroughly
to prevent any dirt from entering the oil tank.
2.
Unscrew the oil filler cap and add oil up to the
lower edge of the filler neck.
3.
Screw the oil filler cap firmly back in place.
4.
Wipe away any spilt chain oil carefully.
NOTE:
When the chain saw is used for the first time, it
•
may take up to two minutes for the saw chain oil to
begin
its
lubricating
mechanism. Run the saw without load until it does
so (see "CHECKS ").
CHECKS
Before starting work, carry out the following checks:
Checking the chain tension
WARNING:
Always withdraw the mains plug before checking
•
the chain tension, and wear safety gloves.
oil.
Waste
oil
contains
effect
upon
the
Fig.15
Make sure the saw chain fits snugly against the lower
side of the bar (see circle).
Check the chain tension frequently, as new chains are
subject to elongation.
Excessively high tension of saw chain may cause
breakage of saw chain, wear of the guide bar and
breakage of the adjusting dial.
A chain which is too loose can jump off the bar, and
therefore presents an accident risk.
If the chain is too loose: Refer to the section titled "
Adjusting saw chain tension " and adjust
chain tension again.
Checking the switch action
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the
"OFF" position when released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.
Do not pull the switch trigger hard without depressing
the lock-off button. This may cause switch breakage.
Checking the chain brake
NOTE:
If the chain saw fails to start, check whether the
•
chain brake is released. To release the chain
brake, pull the hand guard backwards firmly until
you feel it engage.
Fig.16
Fig.17
Check the chain brake as follows:
1.
Hold the chain saw with both hands when
switching it on. Hold the rear handle with your
right hand, the front handle with your left. Make
sure that the bar and the chain do not contact
with any object.
2.
First press the lock-off button, then the switch
trigger. The saw chain starts immediately.
3.
Press the front hand guard forwards using the
back of your hand. Make sure that the saw chain
comes to an immediate standstill.
saw
CAUTION:
If the saw chain does not stop immediately, do not
•
use the saw under any circumstances. Consult
Makita authorized service centers.
Checking the run-down brake
Switch on the chain saw.
Release the switch trigger completely. Make sure the
saw chain comes to a standstill within a second.
13
the saw
Advertisement
Table of Contents
