Related Manuals for True GK2200T
Summary of Contents for True GK2200T
- Page 1 Assembly Instructions GK2200T TREADMILL ASSEMBLY INSTRUCTIONS Frame Assembly 120V 220V...
-
Page 2: Important Safety Instructions
Do not allow the treadmill assembly to rest on the cord. Important Electrical Requirements – 120V Your TRUE treadmill requires a dedicated 120 volt, alternating current (AC), 20 amp grounded outlet circuit. This means nothing else can be plugged into the same circuit. Most power circuits are rated for this 120V AC 20 amp requirement, but you must ensure the treadmill does not share the circuit with anything else. - Page 3 Assembly Instructions GK2200T FRAME COMPONENT CHECKLIST ITEM DESCRIPTION Cup Holder Frame Left Upright Right Upright Left Handrail Right Handrail Upper Shoulder Cover(Left) Upper Shoulder Cover(Right) Lower Shoulder Cover(Left) Lower Shoulder Cover(Right) Handrail cover（left） Handrail cover（right）...
- Page 4 Assembly Instructions GK2200T TREADMILL HARDWARE KIT ITEM DESCRIPTION Belt 3.6x163mm Truss Hex Screw (Ø13) Truss Philips Screw M4xP0.7x10 Inner Toothed Washer M8 Truss Hex Screw M8xP1.25x80 Blue Nylon patch Truss Hex Screw M8xP1.25x40 Blue Nylon patch Cup Holder Fixing Plate Bottled Silicon DC-100 30C.C.
-
Page 5: Tool Requirements
Assembly Instructions TOOL REQUIREMENTS o Hex Key – 5mm, T-Spanner-8 mm, Wrench 17mm (included with hardware kit) o 7/16 Open End Wrench (not included) o Long Nose Pliers (not included) o #2 Phillips Screwdriver (not included) FRAME ASSEMBLY PROCEDURE CAUTION: Use caution when assembling treadmill. Unpacking and assembling of this treadmill is a two person task. -
Page 6: Pedestal Installation
Assembly Instructions 2. PEDESTAL INSTALLATION a. Check that Hex Head Bolts in Fig 2-1 are backed out enough to clear Pedestals when installed. b. Install Pedestal – R (D) into pedestal support on Frame (B) while pulling the cable out of pedestal support as shown in Fig. 2-1. NOTE: Be careful not to pinch cables. - Page 7 Assembly Instructions CABLE CONNECTION – FRAME AREA NOTE: Cables will be labeled near their connector with identifying names such as those listed below in BOLD TEXT. Also listed in these instructions are the cable part numbers (KDCA-“xx”), which are called out in each step. NOTE: Reference Wiring Schematic and Frame Cable Routing Diagram at the end of these Assembly Instructions.
- Page 8 Assembly Instructions 4. CONSOLE RACK and MOTOR COVER INSTALLATION a. Install Console Rack (A) onto Pedestals R & L by resting Console Rack tubing on top of Pedestal tubing cradles. See Fig. 4. CAUTION: Do not pinch cabling during this step. b.
- Page 9 Assembly Instructions PEDESTAL TUBING CRADLE Hex Nut Hex Screw Fig. 4...
- Page 10 Assembly Instructions 5. CONSOLE RACK CABLE CONNECTIONS a. NOTE: Connections in this step will be made from Pedestal - Right to Console Rack. NOTE: All three connections made for any Console model. b. CNTRL Control Cable i. Connect CNTRL Cable (p/n KDCA-2B/XL-1063B) from Pedestal –...
-
Page 11: Handrail Installation
Assembly Instructions 6. HANDRAIL INSTALLATION Insert Handrails (E, F) onto Pedestals and secure with four Bolts -M8 x 80mm (e) and Internal Tooth Washer M8 (d) using 5 mm Hex Key. Fig. 6... - Page 12 Assembly Instructions 7. SHOULDER COVER TOP INSTALLATION Using a Phillips screwdriver, install Shoulder Cover Top pieces Left (G) and Right (H) with three Screws M4 x 10mm (c) on each side as shown in Fig. 7. CAUTION: Make sure cabling is NOT pinched during installation. Fig.
- Page 13 Assembly Instructions 8. SHOULDER COVER BOTTOM INSTALLATION a. Using a Phillips screwdriver (magnetic tip option can be used), install Shoulder Cover Bottom pieces Left (G) and Right (H) with five Screws M4 x 10mm (c) on each side as shown in Fig. 8. CAUTION: Make sure cabling is NOT pinched during installation.
- Page 14 Assembly Instructions 9. HANDRAIL COVER INSTALATION a. Assemble left (L) and right (M) handrail covers with the ribbing plate into the square hole in the left and right handrail as shown in Fig. 9-1. b. Tighten the left (L) and right (M) handrail cover using screw (i) and nylon nut (m) c.
- Page 15 POWER INLET CIRCUIT BREAKER Fig. 9-1: GK2200T Treadmill Front Electrical Panel POWER SWITCH: l = ON, 0 = OFF CIRCUIT BREAKER: In the event the current drawn by the treadmill exceeds a specified threshold value, the Circuit Breaker will operate; the Circuit Breaker will trip, and open the circuit.
- Page 16 Assembly Instructions SAFETY KEY INSTALLATION a. Safety key and attachment cord are wrapped around plate during shipping. See picture below. SAFETY KEY - AS SHIPPED Unwind safety key and cord from plate. Attach Safety Key magnet to front of Center Pod as shown below. Attach Safety Key clip to plate located on Console Rack (when not working out).
- Page 17 Assembly Instructions CLIP MAGNET PLATE LANYARD ATTACHED TO PLATE SAFETY KEY INSTALLED...
- Page 18 Assembly Instructions Electrical Schematic www.LiteGait.com / 800-332-9255 / 1-480-829-1727 2012 Mobility Research Inc. Specifications subject to change 09252012...