Table of Contents
Advertisement
Linear Audio record timing terminal
26 BIAS (H)
O
recording time
SAFETY TAB DETECTION INPUT
27 S.TAB (L)
I
WITH Safety Tab: Input = Low
Audio Mute Output terminal
28 FM MUTE (H)
O
time = 600msec.
interposing the changing point.
AUDIO SYSTEM (TUNER PRESET) select terminal.
29 SW1
O
Mecha position Input
30 POS.SW4
I
31 POS.SW3
I
32 POS.SW2
I
33 POS.SW1
I
34 RESET (L)
I
Reset terminal
35 32KHz IN
I
Sub clock 32.768KHz osc.input
36 32KHz OUT
O Sub clock 32.768KHz osc.output
37 5V (D)
- Digital port Power Vcc (5V)
38 12MHz IN
I
Main clock 12/16MHz osc.input.
39 12MHz OUT
O Main clock 12/16MHz osc.output.
40 GND (OSC)
- OSC circuit Digital GND.
41 NC
Unused terminal. Fixed Output = Low
42 NC
Unused terminal.Fixed Output = Low.
Clock source selection terminal during reset start.
43 32K.START (L)
I
44 LC.OSC IN
I
LC osc. Input terminal
45 LC.OSC OUT
O LC osc. Output terminal
46 GND
- Terminal B for testing. ( connected to GND )
47 4FC LPF
I
Internal OSC Connection terminal for sync generator circuit.
48 FSC IN
I
Sub carrier (fsc) input terminal for sync generator circuit.
49 GND (OSD)
- GND terminal for OSD circuit
50 CV IN
I
Composite Video signal input terminal
KILLER/COLOR Detection Input Terminal.
51 KILLER (H)
I
KILLER : High
Composite Video Signal Output Terminal.(Do not use as common port)
52 CV OUT
O
When recording linear audio, take (H) as output
Output mode: REC,(ADUB,AV-INSERT)
When start recording, set BIAS(H), R.REC(H) output range 140~160msec
When finish recording, BIAS(L) = Output, D.REC(L) Time = 0 ~ 20 msec
Without Safety Tab: Input = High
During P.Off,Head cleaning,Timer Standby,and VPS/PDC Standby,
(After canceling these modes,take (L) as the output after delayed time= 600msec.
During VV,when tape speed is not 1 time speed, Output = High.
(Take (L) as the output, after switching over to 1 time speed,and after delayed
Take (H) as the output During switching over of EE/VV, Output = High after
(Take (L) as the output, after switching over of EE/VV, and delayed time= 600ms.
When J.CLK/A.DEF/NOR terminal is A.DEF, Output = High.
AUDIO SYSTEM = BG, I: High is Output
AUDIO SYSTEM = DK, M: Low is Output
Refer to the mecha timing chart for Input result data control.
POS.SW1
POS.SW2
POS.SW3
0
0
0
0
0
0
0
0
1
0
0
1
0
1
0
0
1
0
0
1
1
0
1
1
1
0
0
1
0
0
1
0
1
1
0
1
1
1
0
1
1
0
1
1
1
1
1
1
Connect Vcc(5V), when 12/16 MHz High speed mode
Connect to Vss(0V), when 32KHz low speed mode
COLOR : Low
POS.SW4
Position
0
1
0
DOWN
1
R-REW
0
LOAD
1
REV
0
PLAY
1
POFF
0
STOP_R
1
STOP_F
0
1
0
FF / REW
1
0
EJECT
1
51
NV-VP60GL / NV-VP60GC / NV-VP60GCS
Low
Low
Low
In
In
In
High
Hi-z
High
Hi-Z
Hi-Z
Hi-Z
In
In
In
In
In
In
In
In
In
In
In
In
In
In
In
In
In
In
Out
Out
Out
-
-
-
In
In
In
Out
Out
Out
-
-
-
Low
Low
Low
Low
Low
Low
In
In
In
In
In
In
Out
Out
Out
-
-
-
In
Low
In
In
Low
In
-
-
-
In
In
In
In
In
In
Out
Out
Out
- Quick Links:
- General Description
- Operating Instructions
Hide quick links:
Advertisement
Table of Contents
