The use of a substitute replacement component which does Leakage 0.5mA current Device not have the same safety characteristics as the PIONEER tester under recommended replacement one, shown in the parts list in test this Service Manual, may create shock, fire, or other hazards.
Page 3
IMPORTANT LASER DIODE CHARACTERISTICS MAXIMUM OUTPUT POWER : 5 mW THIS PIONEER APPARATUS CONTAINS WAVELENGTH : 780 – 785 nm LASER OF CLASS 1. SERVICING OPERATION OF THE APPARATUS S H O U L D B E D O N E B Y A S P E C I A L LY INSTRUCTED PERSON.
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DVJ-1000...
7.1.1 SERVICE MODE ..........................113 7.1.2 HOW TO UPGRADE THE SOFTWARE OF THE MICROCOMPUTER ...........119 7.1.3 HOW TO INPUT THE ID NUMBER ....................120 7.1.4 SEQUENCE .............................122 7.1.5 DVJ-1000 BLOCK CHART (DJ MODE)....................124 7.1.6 DVJ-1000 BLOCK CHART (NORMAL MODE).................126 7.1.7 DISASSEMBLY ..........................128 7.3 PARTS ..............................140 7.3.1 IC..............................140...
Y (luminance) ........... 1 V p-p (75 Ω) C (color) ........286 mV p-p (75 Ω) (NTSC) Note: 300 mV p-p (75 Ω) (PAL) Specifications and design are subject to possible modification Jack ..............4-pin mini DIN without notice. DVJ-1000...
Page 7
Accessories Power Cord Audio Cable Forced Eject Pin (ADG7021 : KUCXJ) (VDE1064) L=1.5m (housed in a groove in (ADG7097 : TLFXJ) the bottom panel) (DEX1021) (ADG1154 : WYXJ5,TLFXJ Control Cord TLXJ/RD) (XDE3063) L=1 m Video Cable (VDE1065) L=1.5m DVJ-1000...
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING DVJ-1000...
Page 9
NSP 18 User Card DRM1262 Operating Instructions(English) See Contrast table(2) • • • • • (2) CONTRAST TABLE DVJ-1000/KUCXJ, /WYXJ5, /TLXJ/RD and TLFXJ types are constructed the same except for the following: DVJ-1000 DVJ-1000 DVJ-1000 DVJ-1000 Mark No. Symbol and Description...
2.2 EXTERIOR SECTION Refer to "2.3 CONTROL PANEL SECTION". Refer to "2.5 SLOT-IN MECHANISM SECTION". 36 57 DVJ-1000...
Page 11
Insulation Sheet DEC2694 PC Support DEC2736 Cushion Shield DEC2905 Gasket L40 DEC2979 (2) CONTRAST TABLE DVJ-1000/KUCXJ, /WYXJ5, /TLXJ/RD and TLFXJ types are constructed the same except for the following: DVJ-1000 DVJ-1000 DVJ-1000 DVJ-1000 Mark No. Symbol and Description /KUCXJ /WYXJ5 /TLXJ/RD /TLFXJ >...
2.3 CONTROL PANEL SECTION 47 56 34 56 Refer to "2.4 JOG SECTION". DVJ-1000...
Page 13
OBA8038 LOOP MODE Lens DNK4594 REC Knob DAC2322 SET Knob (LOOP) DAC2324 (2) CONTRAST TABLE DVJ-1000/KUCXJ, /WYXJ5, /TLXJ/RD and TLFXJ types are constructed the same except for the following: DVJ-1000 DVJ-1000 DVJ-1000 DVJ-1000 Mark No. Symbol and Description /KUCXJ /WYXJ5...
2.5 SLOT-IN MECHANISM SECTION Lubricating oil ∗1 : GYA1001 Daifree ∗2 : GEM1036 ∗1 ∗1 ∗2 ∗2 ∗2 DVPL to CN7005 ∗1 Refer to "2.6 TRAVERSE MECHA. ASSY-S". DVPL to CN7001 DVPL to CN7002 DVPL to CN7003 DVJ-1000...
Page 17
Driver Gear DNK3912 Loading Gear DNK3911 SW Lever Spacer DEC2420 Loading Lever Assy DXB1880 Clamper D4 Assy DXA2043 Clamper Spring DBH1374 Clamper Arm DNK3576 Eject Lever DNK3684 Lever AP DNK3835 Lever BP DNK3836 Guide Spring DBH1375 Disc Guide DNK3478 DVJ-1000...
Page 25
÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ : The power supply is shown with the marked box. DVJ-1000...
3.9 MAIN ASSY(6/8) MAIN ASSY 1/8, 6/8 (DWG1630) (DV) (DV) : Video Data Signal Rout. (DA) : Audio Data Signal Rout. 1/8, 6/8 : Digital Out Signal Rout. (DV) (DA) (DA) (DA) DVJ-1000...
Page 39
: Analog Audio Signal Rout. : Analog Video Signal Rout. DVJ-1000...
3.10 MAIN ASSY(7/8) MAIN ASSY (DWG1630) : Analog Video Signal Rout. : Analog Audio Signal Rout. : Digital Out Signal Rout. CN4505 CN4300 1/8, 8/8 CN4502 DVJ-1000...
Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. MAIN ASSY IC111– 162pin (CLK66M) IC109– 38pin (66MSDR) V:1V/div. H:5nS/div V:1V/div. H:5nS/div MAIN ASSY IC1707– 7pin (27M_CKGEN) IC305– 55pin (27MAV1) V:1V/div. H:20nS/div V:1V/div. H:20nS/div IC305– 64pin (16/36M) IC303– 38pin(MCLK) V:1V/div. H:10nS/div V:1V/div. H:10nS/div DVJ-1000...
Page 65
Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. MAIN ASSY IC503– 38pin (CARD_66M) IC506– 55pin (27M_MOT) V:1V/div. H:5nS/div V:1V/div. H:20nS/div IC506– 16pin (22/24M) IC505– 97pin V:1V/div. H:20nS/div V:1V/div. H:20nS/div MAIN ASSY IC702– 38pin (SLMCLK) V:1V/div. H:10nS/div. DVJ-1000...
Page 66
Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. MAIN ASSY IC904– 38pin (M1CLK) IC906– 38pin (M2CLK) V:1V/div. H:2nS/div. V:1V/div. H:2nS/div. MAIN ASSY IC1502– 48pin (M_PRG27M) IC1506– 48pin (S_PRG27M) V:1V/div. H:20nS/div. V:1V/div. H:20nS/div. IC1510– 7pin (22/24M_DAC) IC1513– 6pin (22/24M_AQE) V:1V/div. H:20nS/div. V:1V/div. H:20nS/div. DVJ-1000...
Page 67
Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. MAIN ASSY CN1703-18pin(MAIN_V) CN1703-16pin(PRE V) V:1V/div. H:200uS/div. V:1V/div. H:200uS/div. ODD Field ODD Field CN1704-6pin(L-OUT) CN1704-5pin(L+OUT) V:2V/div. H:200uS/div. V:2V/div. H:200uS/div. CN1704-2pin(R+OUT) CN1704-1pin(R-OUT) V:2V/div. H:200uS/div. V:2V/div. H:200uS/div. IC2015-5pin(DIS_XCS) IC2015-7pin(DIS_SCLK) V:1V/div. H:500uS/div. V:1V/div. H:1uS/div. DVJ-1000...
Page 68
DJ MODE : PLAY, VINAL, SD IN, MASTAR TEMPO :OFF, SRIDER :0 %, HOT CUE :OFF DISC : DVD-REF-Z1 TITLE35– 01 Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. MAIN ASSY IC2001-45pin (CK) IC2001-46pin (/CK) V:1V/div. H:2nS/div. V:1V/div. H:2nS/div. IC2003-45pin (CK) IC2003-46pin (/CK) V:1V/div. H:2nS/div. V:1V/div. H:2nS/div. DVJ-1000...
Page 69
Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. DVPL ASSY : LPS1 : LPS2 : EMN : EMP In a load inn : LPS1 : LPS2 : EMN : EMP In unloading : TE : TEDRV : T+ : T- In a CD pose DVJ-1000...
Page 70
Note : The encircled numbers denote measuring point in the schematic diagram and pcb diagram. DVPL ASSY : TE : TEDRV : T+ : T- In CD FWD scan : TE : TEDRV : T+ : T- In CD REV scan : FEPEN : FEPCK : FEPDT DVJ-1000...
Symbol In PCB Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator DVJ-1000...
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5.62k Ω 562 x 10 5621 RN1/4PC 5 6 2 1 7 7 7 7 LIST OF HOLE PCB ASSEMBLIES DVJ-1000 DVJ-1000/ DVJ-1000/ DVJ-1000/ Mark Symbol and Description /KUCXJ...
Page 104
7 7 7 7 PCB PARTS LIST FOR DVJ-1000 UNLESS OTHER WISE NOTED Mark No. Description Part No. Mark No. Description Part No. > IC1507 NJM78L05UA MAIN ASSY IC1510 PCM1738EG-3 IC1511,1512 NJM5532MD MISCELLANEOUS IC1513 PD0274A L101 LCYA1R5J2520 IC1701 TC7SHU04FUS1 L1701 LCYA2R2J2520 L2004,2010–2013...
Necessary Adjustment Points When Adjustment points VR3301 Exchange the SLIDER VR (Zero Point ADJ.) Adjustment and Check Points Value of TEMPO indication 0 ± 10mV POWER DVJ-1000 STOP UNLOCK LOCK TIME AUTO The digital multi- MODE EJECT TEXT MODE meter which can...
Page 111
Remove the screw fixing the adjust plate, then screw it into the hole corresponding to the value (-1, -2, -3, +1, or +2) for a load to be added: -1, -2, -3 : To decrease the load +1, +2 : To increase the load Adjust plate To decrease To increase the load the load JOG Check Mode : CANCEL POWER OFF DVJ-1000...
I change version indication with a Cross button for left/right, and it is indication better. Ver 1. 00 Cross button for left/right PL 1. 00 SUB 1. 00 Service mode screen DVJ-1000 SERVICE MODE region number MAIN : Ver 1.00 PLAYER : Ver 1.00 I display a version of each software : Ver 1.00...
Page 114
Communication of the microcomputer of a display part and the microcomputer of a system part cannot be performed. E-9101 Error in mechanical operations Unrecoverable: Turn the power off. The error indication will be cleared. * Notes: E-7016,E-8304,E-8305 and E-8709 are not memorized by the internal memory. DVJ-1000...
Page 115
JOG > JOG rotating to REV < JOG DIRECTION REVERSE EJECT LOCK lock * Notes: As for HOT CUE button LED, as for HOT CUE(A), red, HOT CUE(B) are green, and LED of an orange turns on HOT CUE(C) DVJ-1000...
Page 116
MEMORY Area : If a TOUCH/BRAKE knob is turned to the right, the number of display dots will increase. CUE Area : If a RELEASE/START knob is turned to the right, the number of display dots will increase. Playing Address: If TEMPO slider knob is moved to + side, the number of display dots will increase. DVJ-1000...
Page 117
When a REV direction was pushed with SINGLE LAYER DISC. L0 inside L0 middle L0 outside * A search address is different in inside/middle/outside at total capacity of a Disc in a relative address. * Outside searches about 20000 sector I than a Disc most circumference address. DVJ-1000...
Page 118
* It turns in 2000rpmCAV.I do not come in turn UP more than it. Mode Change If the MASTER TEMPO button is pushed into "player operation mode", MASTER TEMPO LED will light up, and it will shift to the below-mentioned "test operation mode." DVJ-1000...
7.1.2 HOW TO UPGRADE THE SOFTWARE OF THE MICROCOMPUTER POWER REC MODE RELOOP/EXIT REC MODE RELOOP/EXIT FL Display N O - D l S C Release POWER ON DVJ-1000 Version up disc POWER FL Display E R R O R Failure Repeat from Automatically the beginning. POWER OFF...
If error E11 is returned, wait a few moments then enter "IW" again. 8 Enter "EJ" to eject the disc, then turn off the power of the DVJ-1000 then turn it back on. Check that no error is displayed. DVJ-1000...
After a disc is loaded, loading Long press processing of the key In the power ON and startup processes begin. If a disc is loaded, the playback process starts. Reading data, etc. Distinction between DVD/CD CD playback process DVD playback process DVJ-1000...
Page 123
5,000 rpm. 0m01s time point Tracking balance adjustment Spindle starts Adjustment of tracking-error amplitude Searching for 30000H rotating at 3,100 rpm. Off-track threshold adjustment Measuring eccentricity Tracking on Accurate adjustment of focus position Start of acquiring addresses DVJ-1000...
Be sure to visually check the earth spring after it is installed. SLMB Assy Traverse Mecha. Assy 04RM2 STCN Assy Earth spring Mecha. plate SPCN Assy MAIN Assy Slot-in Mecha. G11 Assy Bottom view Bottom view INSW Assy DVPL Assy DVJ-1000...
Page 129
Stand the MAIN Assy. Rear view Remove the eight screws. Remove the six screws. Remove the heatsink plate. Heatsink plate Bottom view MAIN Assy (Side B) IC902 Bottom view IC2005 MAIN Assy DVPL Assy Bottom view Bottom view Diagnosis Diagnosis DVJ-1000...
Page 130
Remove the seven screws. MAIN Assy Bottom view Disconnect the two flexible cables and the three connectors. Remove the six screws. Bottom view Reverse the DVPL Assy. Remove the control panel section. Control panel section DVPL Assy Bottom view DVJ-1000...
Page 131
Earth lead unit Earth lead unit Remove the four float springs G11. Loosen the jumper wire. Remove the slot-in mecha. section. Bottom view Float spring G11 Damper Disconnect the one flexible cable. DVPL Assy Bottom view Slot-in mecha. section DVJ-1000...
Page 132
Unhook the four hooks. Remove the slot-in mecha. G11 Assy. Traverse mecha. Assy 04RM2 Before shipment, be sure to clean the pickup lens, using the following cleaning materials: Cleaning liquid : GEM1004 Cleaning paper : GED-008 Pickup lens Slot-in mecha. G11 Assy DVJ-1000...
Page 133
Remove the three screws. Remove the five screws. Remove the SW ring. Remove the JOG section. Caution: Be careful not to lost SW spring 25. DIPB Assy SW spring 25 SW ring CN4001 JFLB Assy Bottom view JOG section DVJ-1000...
Page 134
JOG holder 1000 Place to adhere the SW cushions HH48/2 Adhere the cushions to the right and left of the engraved arrows (←) (12 positions in total) on the sheet SW. SW cushion HH48/2 Engraved arrow SW cushion HH48/2 Sheet SW DVJ-1000...
Page 135
Mount the cam plate on place it so that the slit of the cam plate aligns with the gear stopper. Align. JOG holder 1000 Cam plate Slit Projection Joint gear 1 Gear stopper Joint gear 1 Slit JOG holder 1000 Cam plate DVJ-1000...
Page 136
Check mode for the JOG Dial." Forced-eject pin Joint gear 2 Joint gear 3 Joint gear 1 Adjust plate Gear spring 200 Cam plate Place it with the side with the indication ">ABS<" facing upward. Cam plate Upper side (With >ABS< embossed) Cam plate DVJ-1000...
Page 137
(DIPB Assy) (SLDB Assy) Notes: • Fold one end of the flat cable along a line 13 mm from the edge. • The folded end of the cable must be inserted to connector A. CN4000 Bottom view (JFLB Assy) DVJ-1000...
Page 138
Bottom view Notes: • Fold one end of the flat cable at the end of the reinforcing plate. Then connect it to connector A. • Fold the flat cable at point B to fold it back. CN7003 (DVPL Assy) DVJ-1000...
Page 139
• Tracking coil resistance value: 4.3 0.65 METHOD FFC is removed from CN7001 of DVPB ASSY after LD short land of PU ASSY, the resistance value between the terminal board conductor sides of 3 Pin and 4 Pin of FFC is measured. DVJ-1000...
Page 141
RF input pin 2 of inside division into 4 (DVD) VCC1 Power supply pin 1 (5V) VIN3 RF input pin 3 of inside division into 4 (DVD) VIN4 RF input pin 4 of inside division into 4 (DVD) VIN1 3-beam sub (CD) input 1 DVJ-1000...
Page 142
DRV12 DRV12(FEPCK) Clock output to FEP DRV13 DRV13(FEPDT) Data input/output to FEP DRV14 DRV14(FEPEN) Enable output to FEP DRAMVSS DRAMVSS GND for DRAM DRAMVDD15 DRAMVDD15 DRAM power supply (DRAMD1R5) DRAMVDD33 DRAMVDD33 Power supply (VD3V) VDD3 VDD3 Power supply (VD3V) DVJ-1000...
Page 143
Ready output to host NDMACK NDMACK Host DMA acknowledge input INTRQ INTRQ Interrupt output to host NIOCS16 NIOCS16 Data bus width selection Address input NPDIAG NPDIAG Address input GNDD VDD3 VDD3 Power supply (VD3V) Address input NCS1FX NCS1FX Chip select input DVJ-1000...
Page 144
HDD6 Data input/output HDD8 HDD8 Data input/output HDD7 HDD7 Data input/output VDDH VDDH Power supply (VD5V) NRESET NRESET Reset input from host MASTER MASTER Connect to VSS P0/SERIAL LPS1 Loading mechanism SW input P1/SERIAL LPS2 Loading mechanism SW input DVJ-1000...
Page 146
VDEC bus cycle latch VDEC_D6 VDEC stream data VDEC_D3 VDEC stream data GNDD VDEC_D1 VDEC stream data PLL_CLK PLL clock GNDD GSL_DREQ GSL data request GSL_DACK GSL data acknowledge GSL_D1 GSL stream data VCCIO4 VLTTL Input/output power supply (3.3V) DVJ-1000...
Page 147
GNDD GND (unused pin) TI_HRDY TI DSP ready VCCIO3 VLTTL Input/output power supply (3.3V) GNDD GNDD GND (unused pin) TI_XHDS1 TI DSP data strobe GNDD VCCIO4 VLTTL Input/output power supply (3.3V) GNDD GND (unused pin) AVD7 AV1 video data DVJ-1000...
Page 148
S_PRG_27M VDEC sub video data clock Chip enable FTCK Pull down GNDD DATA0 COFDAT1 Configuration data FTDI Pull up FTMS Pull up GNDD VCCINT V+1R2 Core power supply (1.2V) GNDD GNDD GNDD GNDD VCCINT V+1R2 Core power supply (1.2V) DVJ-1000...
Page 149
VCCIO6 VLTTL Input/output power supply (3.3V) GND+ GNDD 27M_FPGA Video system clock Host data Host data Host data Host data Host data GNDD VCCINT V+1R2 Core power supply (1.2V) GNDD GNDD GNDD GNDD VCCINT V+1R2 Core power supply (1.2V) DVJ-1000...
Page 150
Host data VCCIO1 Host data VCCIO1 VLTTL Input/output power supply (3.3V) Host data Host data GNDD GND (unused pin) GNDD GND (unused pin) VCCIO8 V+2R5D Input/output power supply (2.5V) GNDD GNDD GND (unused pin) GNDD GND (unused pin) GNDD DVJ-1000...
Page 151
M_DBCLK DSP audio data switching Host data Host data Host data Host data VCCIO8 Host data VCCIO8 V+2R5D Input/output power supply (2.5V) DDR SDRAM data DDR SDRAM data GNDD GND (unused pin) GNDD DQ14 DDR SDRAM data GND+ GNDD DVJ-1000...
Page 153
Power supply for input/output (3.3V) Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus VssQ GNDD Power supply for input/output (0V) Address bus VccQ V+3SH Power supply for input/output (3.3V) Address bus Address bus DVJ-1000...
4 beats later. • One-Track Loop POWER DVJ-1000 STOP When this button is held depressed for 1 sec- ond or more, the chapter loop or track loop play...
Page 157
. Set to REV position for reverse playback. 41. HOT CUE REC MODE button Press to select the HOT CUE button’s function (record/call). ì Defaults to call mode when power is switched on. DVJ-1000...
Page 158
In the case of WAVE display, the varying volume levels of the cur- rently playing track are displayed, with the track sized to fit into the entire 100-dot display width. For guide messages, “Dot Matrix Guide Display Mes- sages”. DVJ-1000...
Using the supplied accessory control cord, this connector can connector. These connectors output monitor images used to be connected to a Pioneer DJ mixer (sold separately) to al- aid the DJ during operation. Outputs various guide messages low control of this unit from the DJ mixer. This facilitates the and displays.
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Refer to "2.6 TRAVERSE MECHANISM ASSY-S SECTION" , Cleaning paper : GED-008 "7.1.7 DISASSEMBLY SECTION". DVJ-1000...