Table of Contents
Advertisement
Available languages
Available languages
INSTALL GRILLE
5. Finish ceiling.
Install ceiling material. Cut out around housing.
6. Attach grille
to housing.
Squeeze grille
springs and insert
them into slots on
each side of
housing.
7. Push grille
against ceil-
ing.
8. Remove
light lens.
Carefully insert a
small flat-blade
screwdriver
between grille and
lens. Pry lens out.
9. Install light
bulbs.
Insert fluorescent
bulb* (supplied)
into its socket.
Purchase a 4W
incandescent
night-light bulb
and screw it into
its socket.
Replace lens.
* Use only one of the following 42W fluorescent lamps:
G.E.
F42TBX827A4P/EOL or F42TBX830A4P/EOL
PHILIPS
PL-T 42W/827/4P/ALTO or PL-T 42W/830/4P/ALTO
SYLVANIA
CF42DT/E/IN/827 or CF42DT/E/IN/830
NEMA Type CFTR42W/GX24q/827 or CFTR42W/GX24q/830
Broan
97016888
MODELS QTXE080FLT • QTXE110FLT • QTXE150FLT
SERVICE PARTS
22
Key No.
Part No.
1
97016466
Housing
2
97016450
Duct Connector-6"
3
98010102
Wiring Plate
4
99170245
Screw, #8-18 X .375 (2 req'd)
5
97016933
Wire Panel/Harness Assembly
6
99020284
Blower Wheel
7
99080562
Motor (QTXE080FLT)
99080580
Motor (QTXE110FLT)
99080565
Motor (QTXE150FLT)
8
99100491
Isolator (4 req'd)
9
97016901
Motor Plate
1 0
99250959
Washer #8 (4 req'd)
1 1
99260558
Nut, Hex Lock #8-32 (4 req'd)
*
97016925
Blower Assembly (QTXE080FLT)
*
97016906
Blower Assembly (QTXE110FLT)
*
97016926
Blower Assembly (QTXE150FLT) (includes key nos. 6 thru 14)
1 2
99500397
Insulation (QTXE150FLT only)
1 3
99420648
Threaded Stud (QTXE150FLT only) (4 req'd)
1 4
99260570
Plastic Nut (QTXE150FLT only) (4 req'd)
1 5
97016864
Ballast Assembly
1 6
99260423
Nut, Hex #8-32 (2 req'd)
1 7
97016866
Grille Assembly (includes key nos. 18 & 20)
1 8
99140199
Grille Spring (2 req'd)
1 9
97016888
Bulb, 42W Fluorescent
2 0
99111284
Lens
2 1
99111293
Spacer (2 supplied)
2 2
QTHB1
Hanger Bar Kit
Order service parts by "Part No." - not by "Key No."
TAB
22
Description
Page 4
Replacement parts can
be ordered on our
website. Please visit us
at www.broan.com
SERVICE NOTE To
remove Blower Assembly:
Unplug motor (7).
Remove screw (4) from
motor plate (9) flange.
Find the single TAB on
the motor plate (located
next to the receptacle).
Push up near motor plate
tab while pushing out on
side of housing. Or insert
a straight-blade
screwdriver into slot in
housing (next to tab) and
twist screwdriver.
99043849A
Advertisement
Table of Contents
