Harman Kardon AVR135 Service Manual page 11

AVR135
t Direct Button: Press this button when the tuner
is in use to start the sequence for direct entry of a sta-
tion's frequency. After pressing the button, simply
press the proper Numeric Keys r to select a sta-
tion. (See page 26 for more information on the tuner.)
u Tuning Up/Down: When the tuner is in use, these
buttons will tune up or down through the selected fre-
quency band. If the Tuner Mode Button s& has
been pressed so that AUTO appears in the on-
screen display and Lower Display Line
and holding either of the buttons for three seconds will
cause the tuner to seek the next station with acceptable
signal strength for quality reception. When MANUAL
appears in the Lower Display Line
¯
buttons will tune stations in single-step increments. (See
page 26 for more information.)
v OSD Button: Press this button to activate the
On-Screen Display (OSD) system used to set up or
adjust the AVR 135's parameters.
w Dolby Mode Selector: This button is used to
select from among the available Dolby Surround pro-
cessing modes. Each press of this button will select
one of the Dolby Pro Logic II modes or Dolby 3
Stereo. When a Dolby Digital-encoded source is in use,
the Dolby Digital mode may also be selected. (See
page 24 for the available Dolby surround mode
options.)
x DTS Digital Mode Selector: When a DTS-
encoded digital source is selected, each press of this
button will scroll through the available DTS modes. The
specific choice of modes will vary according to whether
or not the source material contains DTS-ES 6.1
Discrete encoding. When a DTS source is not in use,
this button has no function. (See page 24 for the avail-
able DTS Digital options.)
y Logic 7 Mode Select Button: Press this button
to select from among the available Logic 7 surround
modes. (See page 24 for the available Logic 7
options.)
z Skip Up/Down Buttons: These buttons do not
have a direct function with the AVR 135, but when
used with a compatibly programmed CD or DVD
changer they will change to the previous disc in the
changer or carousel.
` Transport Controls: These buttons do not have
any functions for the AVR 135, but they may be
programmed for the forward/reverse play operation
of a wide variety of CD or DVD players, and audio or
video cassette recorders. (See page 32 for more
information.)
28 Stereo Mode Select Button: When the button
is pressed so that DSP SURR OFF appears in
the Lower Display Line ¯, the AVR will operate in
a bypass mode with true, fully analog, two-channel
left/right stereo mode with no surround processing or
bass management, as opposed to other modes where
digital processing is used. When the button is pressed
so that SURROUND OFF appears in the Lower
Display Line ¯, you may enjoy a two-channel pre-
sentation of the sound along with the benefits of bass
management. Depending on whether your system is
configured for 5.1 or 6.1/7.1 channels, the next press
of the button will cause either 5 CH STEREO or
7 CH STEREO to appear, and the stereo signal
¯ , pressing
will be routed to all five (or seven) speaker channels.
(See page 24 for more information on stereo play-
back modes.)
29
DTS Neo:6 Mode Select: Press this button to
, pressing these
select a DTS Neo:6 mode. These modes take a two-
channel stereo- or matrix surround-encoded source
and create a full five-, six- or seven-channel sound
field. (See page 24 for the DTS Neo:6 options.)
30 Macro Buttons: Press these buttons to store or
recall a "Macro" , which is a preprogrammed sequence
of commands stored in the remote. (See page 32 for
more information on storing and recalling macros.)
31 Disc Skip Button: This button has no direct
function for the AVR 135 but is most often used to
change to the next disc in a CD or DVD player when
the remote is programmed for that type of device.
(See page 31 for more information on using the
remote with products other than the AVR 135.)
32
Preset Up/Down: When the tuner is in use,
press these buttons to scroll through the stations
programmed into the AVR 135's memory. When
some source devices, such as CD players, VCRs and
cassette decks, are selected using the device Input
Selectors e, these buttons may function as
Chapter Step or Track Advance.
Clear Button: Press this button to clear incorrect
33
entries when using the remote to directly enter a radio
station's frequency.
34 Memory Button: Press this button to enter a
radio station into the AVR 135's preset memory. First,
tune the desired station, and then press this button.
Two underline indicators will flash at the right side of
the Upper Display Line ˜, and within five seconds
press the Numeric Keys r for the preset number
between 01 and 30 that you wish to assign to the
station. (See page 26 for more information.)
35
Delay/Prev Ch.: Press this button to begin
the process for setting the delay times used by the
AVR 135 when processing surround sound. After
pressing this button, the delay times are entered by
pressing the Set Button p and then using the
Buttons n to change the setting. Press the
/
⁄ ¤
Set Button p again to complete the process.
(See page 19 for more information.)
REMOTE CONTROL FUNCTIONS
36
the process of configuring the AVR 135's bass man-
agement system for use with the type of speakers
used in your system. Once the button has been
pressed, use the
channel you wish to set up. Press the Set Button
p and then select another channel to configure.
When all adjustments have been completed, press
the Set Button p twice to exit the settings and
return to normal operation. (See page 17 for more
information.)
37
for the AVR 135.
38
or lower the system volume.
39
direct function on the AVR 135, but when used with a
compatible VCR, DVD or satellite receiver, pressing this
button will switch between the output of the device
and the external video input.
40
this button to select the device connected to the
6/8-Channel Direct Inputs f. (See page 22 for
more information.)
41
the AVR 135 or TV set being controlled, depending on
which device has been selected. When the AVR 135
remote is being programmed to operate another device,
this button is pressed with the Input Selector Button
e to begin the programming process. (See page
30 for more information on programming the remote.)
REMOTE CONTROL FUNCTIONS
11
harman/kardon
Speaker Select: Press this button to begin
Buttons n to select the
/
⁄ ¤
Spare Button: This button has no direct function
Volume Up/Down: Press these buttons to raise
TV/Video Selector: This button does not have a
6-Channel/8-Channel Direct Input: Press
Mute: Press this button to momentarily silence
11