Broan QP430SS Instruction Manual
Hide thumbs Also See for QP430SS:

Advertisement

EVOLUTION
QP4 Series Range Hoods
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code
authorities.
5. This product may have sharp edges. Be careful to avoid cuts
and abrasions during installation and cleaning.
6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. Use only metal ductwork.
9. Do not use this fan with any solid-state speed control device.
10. As an alternative, this product may be installed with the
UL-approved cord kit designated for the product, following
instructions packed with the cord kit.
11. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
flambéing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
3. Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,
or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
4
TM
FOR DOMESTIC COOKING ONLY
MODELS QP430SS • QP436SS • QP442SS
WARNING
2. NEVER PICK UP A FLAMING PAN — You may be burned or
spread the fire.
3. DO NOT USE WATER, including wet dishcloths or towels - a
violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher, and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Firesafety Tips" published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced
impeller, keep drywall spray, construction dust, etc., off power
unit.
4. Do not use over cooking equipment greater than 70,000
BTU/hr. as the blower motor will shut down intermittantly.
5. Your hood motor has a thermal overload which will
automatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues
to shut off and restart, have the hood serviced.
6. The top of the hood MUST NOT BE LESS than 30" and at a
maximum of 36" above cooktop for best capture of cooking
impurities.
7. This hood is not intended to be used as a shelf.
8. Please read specification label on product for further
information and requirements.
Register your product online at: www.broan.com
Installer: Leave this manual
with the homeowner.
Homeowner: Cleaning, Maintenance and
Operating instructions on page 2.
Page 1

Advertisement

Table of Contents
loading

Summary of Contents for Broan QP430SS

  • Page 1 MODELS QP430SS • QP436SS • QP442SS Page 1 EVOLUTION QP4 Series Range Hoods READ AND SAVE THESE INSTRUCTIONS FOR DOMESTIC COOKING ONLY WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR 2. NEVER PICK UP A FLAMING PAN — You may be burned or INJURY TO PERSONS, OBSERVE THE FOLLOWING: spread the fire.
  • Page 2: Operation

    MODELS QP430SS • QP436SS • QP442SS Page 2 CONTENTS OPERATION Always turn the hood ON before cooking in order to establish an INCLUDED WITH THE HOOD: air flow in the kitchen. After turning off the range, let the hood run for a few minutes to clear the air. (1) 3¼” X 14” Operate the hood as follows: DAMPER / DUCT CONNECTOR GREASE FILTERS (2 - FOR 30” & 36” HOODS) (3 - FOR 42” HOODS) (1) 7”...
  • Page 3: Sleep Mode

    MODELS QP430SS • QP436SS • QP442SS Page 3 CLOCK SETTING 10-MINUTE DELAY OFF Press the button once, the “hours” will begin blinking in the When your hood fan is on (any speed) press the button to LED screen. Use the and buttons to set the appropriate activate the delay off feature. When activated, the hood fan will hours for the clock. A small indicator will illuminate in the left automatically turn off after 10-minutes has elapsed. The delay...
  • Page 4: Make-Up Air Damper

    Note: Canadian version does not have this function. WIRES FUSES DAMPER MOTOR RANGE HOOD CONTROL BOARD MAIN LIGHT FUSE FUSE REMOTE CONTROL The hood is compatible with Broan RF Remote Control Model BCR1 (optional). Purchase separately. The Range Hood Control Board contains a Main Fuse and a Light Fuse to protect the controls from power surges. If a fuse has opened (blown), the green fan setting or light setting indicators will not operate properly when the fan or light buttons are pressed, and the fan and lights will not turn on. New fuses can be purchased at your local electronic supply store. Use 8A, 120V, 5 mm diameter, 20 mm long, fast-acting, cartridge- type fuses. To replace a fuse (by qualified person(s): 1. Disconnect power at service entrance.
  • Page 5: Prepare Hood Location

    MODELS QP430SS • QP436SS • QP442SS Page 5 PREPARE HOOD LOCATION 7-INCH ROUND DISCHARGE ROOF CAP 3¼" X 14" or DUCT & ELECTRICAL CUTOUTS 7" ROUND DUCT (For vertical discharge) 9" 8" DIA. HOLE 7-IN. ROUND 7-IN. ROUND SOFFIT DUCT DUCT "...
  • Page 6: Prepare The Hood

    MODELS QP430SS • QP436SS • QP442SS Page 6 PREPARE THE HOOD Remove parts bag and 3¼” x 14” damper/duct connector 3¼” X 14” from inside the hardware box included with the hood. DAMPER / DUCT CONNECTOR TOP/BACK Remove all protective polyfilm from the hood. EDGE OF HOOD DAMPER FLAP PIVOT 7” ROUND DUCT PLATE Remove 6 Screws holding Bottom Pan to hood. Set bot- tom pan and screws aside. VERTICAL 7” ROUND & 3¼” X 14” INSTALLATION SCROLL ONLY: Attach 3¼” x 14” Damper/Duct Connector (if using 3¼”...
  • Page 7: Install The Hood

    MODELS QP430SS • QP436SS • QP442SS Page 7 INSTALL THE HOOD CONNECT THE WIRING WARNING To reduce the risk of electrical shock, switch power off at service panel. Lock or tag service panel to prevent GROUND power from being switched on accidentally. SCREW HOUSE POWER CABLE ELECTRICAL WIRING BOX COVER Connect House Power Cable to range hood wiring - BLACK to BLACK, WHITE to WHITE, and GREEN or BARE WIRE to Ground Screw. Replace electrical wiring box cover. FOR 30” MODEL ONLY: Replace rubber bushing, re-connect left-hand light panel ELECTRICAL electrical connector, and re-attach light panel with (2) POWER screws removed in Step 6.
  • Page 8: Service Parts

    97017735 Parts Bag you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties. 99526707 Suction Cup Tool 97018252 Heat Sensor To qualify for warranty service, you must (a) notify Broan-NuTone at the 97018253 Fuse address or telephone number below, (b) give the model number and part 97018261 Ribbon Cable Kit (contains 3) identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the V05921 50W Halogen GU10 Bulb original purchase date.

This manual is also suitable for:

Qp436ssQp442ss

Table of Contents