Samsung DVD-D360K User Manual page 5

- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture quality.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this
DVD player using your TV remote control. This is only available with Samsung TVs that support
Anynet+(HDMI-CEC).
- If your TV has an logo, then it will
• HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital transmission of video and audio data with just a single
connector.Using HDMI, the DVD player transmits a digital video and audio signal and displays a
vivid picture on a TVhaving an HDMI input jack.
• HDMI connection description HDMI connector
- Both uncompressed video data and digital audio data (LPCM or Bit Stream data).- Though the
player uses a HDMI cable, the player outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears
on the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a DVD, the data trans-
mitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an
analog-to-digital converter (in the TV) is required. During this conver-sion, the picture quality is
degraded due to noise and signal loss. DVI technology is superior because it requires no D/A con-
version and is a pure digital sig-nal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted
via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a
display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized.
D. Connection to an Audio System (2 Channel Amplifier, Dolby Digital,
or MPEG2 )
1. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD
player to the AUDIO (red and white) IN terminals of the Amplifier. If using a coaxial cable, connect
the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO
IN (COAXIAL) terminal of the Amplifier.
2. Using the video signal cable(s), connect the VIDEO, COMPONENT or HDMI OUT terminals on the
rear of the DVD player to the VIDEO, COMPONENT or DVI IN terminals of your TV
3. Turn on the DVD player, TV, and Amplifier.
4. Press the input select button of the Amplifier to select external input in order to hear sound from the
DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input.
E. Connecting to a TV (SCART)
1. Using Scart cable, connect to SCART terminal on the rear of the DVD player to the SCART IN
terminals of TV.
2. Turn on the DVD player and TV.
3. Press the input selector on your TV remote control until the Video signal from the DVD player
appears on the TV screen.
Supports the Anynet+ Function.
DVD-D530K
DVD-D530
D
Coaxial Kabel
GREEN
BLUE
WHITE
RED
YELLOW RED
Audio Kabel A Video
B Compoent
kabel
E
kabel
Scartkabel
YELLOW
RED BLUE
GREEN
RED
DVD-D360K
D
Coaxial Kabel
BLUE GREEN
WHITE
RED
RED
YELLOW
A
Video
Audiokabel kabel
B
E
Component kabel
Scartkabel
YELLOW BLUE
WHITE
GREEN
RED
RED
2-Channel stereo amplifier
Audio Kabel
WHITE
RED
C
HDMI Kabel
OR
HDMI-DVI Kabel
2-Channel stereo amplifier
RED WHITE
Audio Kabel
WHITE
RED
Do not use the connection
Scart and Component Video
(Y.Pb,Pr) Simultaneously
Do not use the
connection Scart
and Component
Video (Y.Pb,Pr)
Simultaneously
5