Process After Fixing Flash Error - Sony DSC-HX9V Service Manual

Ver. 1.1 2011.07
The changed portions from
Ver. 1.0 are shown in blue.
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Block Detailed
Function Code
The internal memory has experienced a
media error.
The internal memory has experienced a
format error.
Memory card is unformatted.
C 1 3 0 1
Memory card is broken.
Memory card type error.
The camera cannot read or write data on
the memory card.
Trouble with hardware.
C 3 2 0 1
E 4 1 0 0 * Abnormality of network control.
E 4 1 0 1 * Abnormality of network control device.
Difficult to adjust focus.
E 6 1 0 0
(Cannot initialize focus)
Zoom operations fault.
E 6 1 1 0
(Cannot initialize zoom lens.)
Reset position detection error on the step-
E 6 1 3 0
per iris initializing.
E 6 2 0 2 Abnormality of IC for steadyshot.
E 6 2 1 0 Lens initializing failure.
E 6 2 1 1 Lens overheating (PITCH).
Lens overheating (YAW).
E 6 2 1 2
Abnormality of thermistor.
E 6 2 2 0
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note 1)
E 9 1 0 1
E 9 4 0 0 Internal memory fault.
GPS hardware error.
E 9 5 0 0
Acceleration sensor hardware error.
E 9 5 0 1
(GPS hardware error)
Electronic compass hardware error.
E 9 5 0 2
(GPS hardware error)
Note 1: After repair, be sure to perform "1-6. PROCESS AFTER FIXING FLASH ERROR".
Note 2: Functions of codes with * mark are not provided in this unit.
DSC-HX9/HX9V_L2
Correction
Turn the power off and on again.
Format the internal memory.
Format the memory card.
Insert a new memory card.
Insert a supported memory card.
Turn the power off and on again, or taking out and inserting the memory
card several times.
Turn the power off and on again.
Turn power off and turn power on again.
Turn power off and turn power on again.
Retry turn the power on by the power switch. If it does not recover, check
the focus reset sensor of lens block (pin wj, wl of CN403 on the SY-286
board). If it is OK, check the focus motor drive IC (IC202 on the SY-286
board).
Retry turn the power on by the power switch. Check the zoom reset sensor
of lens block (pin rg of CN403 on the SY-286 board) when zooming is
performed when the zoom button is operated. If it is OK, check the zoom
motor drive IC (IC202 on the SY-286 board).
Turn power off and turn power on again.
Check or replacement of the IC for steadyshot (IC401 on the SY-286
board).
Check or replacement of the IC for steadyshot (IC401 on the SY-286
board).
Check the HALL element (PITCH) of optical image stabilizer (pin 8, qa
of CN403 on the SY-286 board). If it is OK, check PITCH angular velocity
sensor (SE401 on the SY-286 board) peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pin qa, qd
of CN403 on the SY-286 board). If it is OK, check YAW angular velocity
sensor (SE401 on the SY-286 board) peripheral circuits.
Check the OIS temp sensor of optical image stabilizer (pin ea of CN403
on the SY-286 board).
Inspect the internal memory (IC201 on the SY-286 board).
Check whether the RL-115 flexible board of connected between SY-286
board and RL-109 board is broken, and check whether it is inserted im-
perfectly. If there is no problem the coaxial cable or flexible board, inspect
or replacement of the SY-286 or RL-109 board.
Check whether the RL-115 flexible board of connected between SY-286
board and RL-109 board is broken, and check whether it is inserted im-
perfectly. If there is no problem the coaxial cable or flexible board, inspect
or replacement of the SY-286 or RL-109 board.
Check whether the RL-115 flexible board of connected between SY-286
board and RL-109 board is broken, and check whether it is inserted im-
perfectly. If there is no problem the coaxial cable or flexible board, inspect
or replacement of the SY-286 or RL-109 board.

1-6. PROCESS AFTER FIXING FLASH ERROR

When "FLASH error" (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed
automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be on the HOME screen.
Method for Initializing the Flash Error Code
Reset Flash Error using the Flash Error Repair Tool Ver_[].[].exe.
1-7. Reading QR Code
The lens data of this unit is read from the QR code.
The QR code can be read by using a USB web camera or from an image captured with a digital camera or similar.
Read the lens data in the following way.
Note 1: Use a USB web camera provided with manual focus and macro shooting functions.
Note 2: When using a USB web camera, do not use the standard Windows driver.
Install the dedicated driver for the USB web camera to be used.
When a USB web camera is used
1. Connect a USB web camera to the PC and install the dedicated driver to make the camera available.
2. Start the Adjust Manual.
3. Click the QR code reader button to activate the QR code reader.
4. Read the QR code with the USB web camera.
When replacing the lens: Read the QR code attached to the lens for service.
When replacing the board: The QR code need not be read.
5. Save the lens data with a file name.
When a digital camera is used
1. Shoot the QR code with a digital camera and save the data in the PC.
2. Start the Adjust Manual.
3. Click the QR code reader button to activate the QR code reader.
4. Click the LOAD button to open the saved image.
5. Save the lens data with a file name.
1-3
– ENGLISH –