General Instructions; General Information; Care Of Glass, And Plated Parts - Napoleon BGD42 Installation And Operation Instructions Manual

4

GENERAL INSTRUCTIONS

THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERVICED BY
A QUALIFIED INSTALLER to conform with local codes. In absence of
local codes, install the BGD42 to the current National Fuel Gas Code,
ANSI Z223.1, or the current CAN/CGA B149, Installation Codes.
Installation practices vary from region to region and it is important to
know the specifi cs that apply to your area,
for example: in Massachusetts State:
• The fi replace damper must be removed or welded in the open
position prior to installation of a fi replace insert or gas log.
• The appliance off valve must be a "T" handle gas cock.
• The fl exible connector must not be longer than 36".
• The appliance is not approved for installation in a bedroom or
bathroom unless the unit is a direct vent sealed combustion
product.
• WARNING: This product must be installed by a licensed plumber
or gas fi tter when installed within the commonwealth of Mas-
sachusetts.
Mobile home installation must conform with local codes or in the absence
of local codes, install to the current standard for gas equipped mobile
housing CAN/CSA ZA240 MH Series in Canada or the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or
the Fire Safety Criteria for Manufactured Home Installations, Sites and
Communities Standard ANSI/NFPA 501A in the United States.
The fi replace and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa). The fi replace
must be isolated from the gas supply piping system by closing its
individual manual shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or less than 1/2 psig
(3.5 kPa).
When the fi replace is installed directly on carpeting, vinyl tile or
other combustible material other than wood fl ooring, the fi replace
shall be installed on a metal or wood panel extending the full width
and depth.
If the optional fan or blower is installed, the junction box must be
electrically connected and grounded in accordance with local codes.
In the absence of local codes, use the current CSA C22.1 CANADIAN
ELECTRICAL CODE in Canada or the ANSI/NFPA 70 NATIONAL
ELECTRICAL CODE in the United States.

GENERAL INFORMATION

FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN TEST-
FIRED TO ASSURE ITS OPERATION AND QUALITY! Maximum input
is 28,500 BTU/hr for natural gas and 24,000 BTU/hr for propane.
When the fi replace is installed at elevations above 4,500ft, and in the
absence of specifi c recommendations from the local authority having
jurisdiction, the certifi ed high altitude input rating shall be reduced at
the rate of 4% for each additional 1,000ft.
Maximum output for natural gas is 19,500 BTU/hr at an effi ciency of
68.5% with the fan on, and 16,000 BTU/hr for propane at an effi ciency
of 67% with the fan on. The maximum A.F.U.E. (annual fuel utilization
effi ciency) rating is 64% for natural gas and 61.5% for propane.
Minimum inlet gas supply pressure is 4.5" water column for natural
gas and 11" water column for propane. Maximum inlet gas pressure
is 7" water column for natural gas and 13" water column for propane.
Manifold pressure under fl ow conditions is 3.5" water column for
natural gas and 10" water column for propane.
This fi replace is approved for bathroom, bedroom and bed-sitting room
installations and is suitable for mobile home installation.
No external electricity (110 volts or 24 volts) is required for the
gas system operation.
Expansion / contraction noises during heating up and cooling
down cycles are normal and are to be expected.
W415-0381 / H / 12.07.07

CARE OF GLASS, AND PLATED PARTS

Do not use abrasive cleaners to clean plated parts. Buff lightly with a
clean dry cloth. The BGD42 is factory equipped with tempered glass.
The glass thickness is 3/16". Use only replacement glass available
from your Napoleon® dealer. DO NOT SUBSTITUTE MATERIALS.
Clean the glass after the fi rst 10 hours of operation with a recom-
mended gas fi replace glass cleaner. Thereafter clean as required.
DO NOT CLEAN GLASS WHEN HOT! If the glass is not kept clean
permanent discolouration and / or blemishes may result.
Use only accessories designed for and listed with your spe-
cifi c fi replace.
Provide adequate ventilation air. Provide adequate accessibil-
ity clearance for servicing and operating the fi replace. Never
obstruct the front opening of the fi replace.
For safe and proper operation of the fi replace follow the venting
instruction exactly.
Deviation from the minimum vertical vent length can create dif-
fi culty in burner start-up and/or carboning.
Provide a means for visually checking the vent connection to
the fi replace after the fi replace is installed.
In order to avoid the possibility of exposed insulation or vapour
barrier coming in contact with the fi replace body, it is recom-
mended that the walls of the fi replace enclosure be 'fi nished',
(i.e. drywall/sheetrock) as would any other outside wall of the
home. This will ensure that clearance to combustibles is main-
tained within the cavity.
Vent lengths that pass through unheated spaces (attics, garages,
crawl spaces) should be insulated with the insulation wrapped
in a protective sleeve to minimize condensation.
Objects placed in front of the fi replace must be kept a minimum
of 48" away from the front face of the unit.