Advertisement
Quick Links
Operation 3M-30
Time
Slot
Day
Time
of day
Target
Temperature
Statement of use: The 3M-30 can be used with millivolt, 24VAC,
single and 2 stage conventional systems, gas/oil/electric heat, 1
stage heat pumps, 2 stage heat pumps, zoned hot water (2 or 3 wire),
zoned forced air, single and 2 stage cooling and hybrid systems.
Basic Screens
The MODE SWITCH of the 3M-30 must be in the HEAT or the COOL position to access all
control functions. The 3M-30 Thermostat has 3 basic screens.
The HOME screen is displayed when unit is operating your system.
Touching the
Time of day
Touch here
to change
from 12 to 24hr
clock display.
Target
Temperature
HOME screen
Current
Room Temperature
Thermostat
Touch
Mode
Screen
will always return you to this screen.
Day
Using a TOUCH SCREEN
Mode
Please take a moment to try out your
Switch
touch screen itself.
To select a function on the touch
screen, place your finger on the main
Fan
temp display and give a short firm push.
Switch
Try a "tap" of the finger or stylus. Your
Menu
input must last long enough for the
button
system to determine it is not an
Program
accidental 'bump'.
button
Using the stylus is more comfortable
for some users. Again allow the system
enough time to recognize your inputs.
When you are comfortable with touch
inputs, proceed.
Chirp indicator
Time
Slot
Current Room
Temperature
Thermostat
Mode
1
PG
2
PG
Advertisement
Related Manuals for 3M 3M-30
Summary of Contents for 3M 3M-30
-
Page 1: Home Screen
2 stage cooling and hybrid systems. Basic Screens The MODE SWITCH of the 3M-30 must be in the HEAT or the COOL position to access all control functions. The 3M-30 Thermostat has 3 basic screens. -
Page 2: Menu Screen
MENU screen Displayed when the MENU button is pressed. Set Day Touch this to set temperature Touch this area to set display. the day of the week. Set Time Return Touch this area to set HOME the time of day. Left arrow goes back, right arrow goes forward. - Page 3 The Mode Switch must be in Configure HEAT or COOL mode to configure. Press MENU to configure the thermostat (from HOME screen). Set day of the week - Touch the Day of the week area to cycle through the days of the week to select the current day.
- Page 4 Program NOTE: 60 Second Rule-During programming, if a button is not pushed in 60 seconds, the unit will return to the home screen. Everything you have changed while programming will automatically be saved. Select HEAT with the HEAT/Cool MODE switch. Press PROGRAM to go to the programming screen.
- Page 5 Manual The 3M-30 has 3 manual override commands. These are accessed by touching the Current Temp Display at the HOME screen (center of screen). Target Temperature Return HOME HOLD Touch this area to set a comfortable target temp for the system to hold until you return and remove HOLD.
- Page 6 At the HOME screen touch the time to toggle from 12 to 24 hr display. Filter The 3M-30 has a feature that keeps track of actual furnace run time and reminds you to periodically replace your system's air filter. Press MENU (from HOME screen) and touch FILTER icon.
- Page 7 When the heat pump is again operational, be sure to change jumper 3 back to the B position as the Auxiliary heat is more expensive than the heat pump. 3M-30 Features This thermostat can be used with all millivolt and 24VAC heating and cooling systems.
- Page 8 Calibration NOTE: Your thermostat comes from the factory calibrated to + or - F actual temperature. It is an accurate instrument. If you want your thermostat to display the same temperature as another thermometer in your home, you can adjust it. Maximum calibration is +/-6 To change the calibration: With the switch MODE in HEAT or COOL.