Download
Share
Print this page
HP 425 802.11n Quick Start Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Wireless Access Point
  5. 425 802.11n
  6. Quick start manual

HP 425 802.11n Quick Start Manual

Wireless dual radio
Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
The HP 425 AP is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED
802.11n/a/b/g product. The Wi-Fi CERTIFIED Logo is a
certification mark of the Wi-Fi Alliance.
This Quickstart shows you how to install and get started using the HP 425 Dual Radio 802.11n Access Point, hereafter referred to as the AP.
Important: Minimum controller software versions are required to operate this AP. For more information, see the HP MSM3xx / MSM4xx and HP 425 Access
Points Release Notes v6.2.x. The latest HP documentation is available at www.hp.com/support/manuals.

Hardware overview

2 1
2
2 3
2 4
1: Status LED
4: Ethernet port
2: Reset button
5: Power connector
3: Console port
6: 5 GHz antenna ports (2)
HP 425 802.11n Access Point Quickstart
2 5
2 6
2 6
7: Rubber feet (4)
8: 2.4
GHz antenna ports (2)
9: Mounting hook holes (3)
In
AP part numbers
JG654A (WW), JG653A (AM), JG655A (JP), JG656A (IL).
Package contents
The AP, mounting hardware, rubber feet, MAC address label, and
documentation.
7
2 8
2 9
2 8

Advertisement

loading

Related Manuals for HP 425 802.11n

Summary of Contents for HP 425 802.11n

  • Page 1: Hardware Overview

    HP 425 802.11n Access Point Quickstart This Quickstart shows you how to install and get started using the HP 425 Dual Radio 802.11n Access Point, hereafter referred to as the AP. Important: Minimum controller software versions are required to operate this AP. For more information, see the HP MSM3xx / MSM4xx and HP 425 Access Points Release Notes v6.2.x.

  • Page 2: Radios And Antennas

    HP 425 Wireless Dual Radio 802.11n Access Point Quickstart Important information to read before installing Ports Plenum installation: The AP can be installed in a plenum. The AP is suitable for use in environmental air space in accordance with Section 300-22(C) of the •...

  • Page 3: Selecting The Installation Site

    2: Screw hole 3: Clip 4: T-rail hook cut-out HP recommends that you connect power and verify the Ethernet cable and LEDs before you install the AP in a hard-to-reach location. Record the MAC address and AP serial number for future reference.
  • Page 4 HP 425 Wireless Dual Radio 802.11n Access Point Quickstart Installation Loosen, but do not remove all four M3 screws (7) on the clip holders (3). Hook the mounting bracket clip (3) onto the T-rail holder mounting hook (2). 1: T-rail clip...
  • Page 5 AP and the controller are on the same subnet and have IP connectivity. For more information about using the AP with HP 10500/7500 WLAN Module, HP 830, or WX5002/WX5004 Controllers, see the HP 830 Switch and HP 10500/7500 20G Module Access Controller Module Basic Configuration Guide, or the H3C WX Series Access Controller Module Configuration Guide.
  • Page 6 AP status LEDs your radio settings, it may be mandatory to reduce the radio transmission power level to maintain regulatory compliance. For specific power limits for your country, see the HP 425 AP Antenna Power-Level Setting Guide available LED color State Description from www.hp.com/support/manuals.