Determine Installation Location - Rinnai c199i Installation And Operation Manual

Determine Installation Location

You must ensure that clearances will be met and that
the vent length will be within required limits. Consider
the installation environment, water quality, and need
for freeze protection. Requirements for the gas line,
water lines, electrical connection, and condensate
disposal can be found in their respective installation
sections of this manual.
Water Quality
Consideration of care for your water heater should
include evaluation of water quality.
The water must be potable, free of corrosive chemicals,
sand, dirt, or other contaminates. It is up to the
installer to ensure the water does not contain corrosive
chemicals, or elements that can affect or damage the
heat exchanger. Water that contains chemicals
exceeding the levels below affect and damage the heat
exchanger. Replacement of the heat exchanger due to
water quality damage is not covered by the warranty.
Total Hardness
Aluminum *
Chlorides *
Copper *
Dissolved Carbon Dioxide (CO2)
Iron *
Manganese *
pH *
TDS (Total Dissolved Solids) *
Zinc *
* Source: Part 143 National Secondary Drinking Water Regulations
If you install this water heater in an area that is known
to have hard water or that causes scale build-up, the
water must be treated and may require more frequent
heat exchanger flushing schedule.
When scale build-up in the heat exchanger begins to
affect the performance of the water heater, a diagnostic
code "LC#" will display. Flush the heat exchanger to
prevent damage to it. Scale build up is caused by hard
water and can be accelerated if the unit is set at a high
temperature.
Rinnai offers Southeastern Filtration's "ScaleCutter
Water Conditioning System" that offers superior lime
scale prevention and corrosion control by feeding a
blend of control compounds into the cold water supply.
Part Number
103000038
ScaleCutter System 3/4" Feed
103000039
6
Maximum Level
Up to 200 mg / L
Up to 0.2 mg / L
Up to 250 mg / L
Up to 1.0 mg / L
Up to 15.0 mg / L or PPM
Up to 0.3 mg / L
Up to 0.05 mg / L
6.5 to 8.5
Up to 500 mg / L
Up to 5 mg / L
Description
Southeastern Filtratrion
ScaleCutter Refill
Environment
Air surrounding the water heater, venting, and vent
termination(s) is used for combustion and must be free
of any compounds that cause corrosion of internal
components. These include corrosive compounds that
are found in aerosol sprays, detergents, bleaches,
cleaning solvents, oil based paints/ varnishes, and
refrigerants. The air in beauty shops, dry cleaning
stores, photo processing labs, and storage areas for pool
supplies often contains these compounds. Therefore it
is recommended that outdoor models be used for these
locations where possible.
The water heater, venting, and vent termination(s)
should not be installed in any areas where the air may
contain these corrosive compounds. If it is necessary for
a water heater to be located in areas that may contain
corrosive compounds, the following instructions are
strongly recommended.
IMPORTANT CONSIDERATIONS FOR:
Indoor/Internal Water Heaters

DO NOT Install in areas where air for combustion
might be contaminated with chemicals.

Before installation, consider where air has the
ability to travel within the building to the water
heater.

Where possible, install the water heater in a sealed
closet so that it is protected from the potential of
contaminated indoor air.

Chemicals that are corrosive in nature should not
be stored or used near the water heater.
Outdoor/External Water Heaters and Vent
Terminations of Indoor/Internal Water Heaters

Install the water heater as far away as possible
from exhaust vent hoods.

Install as far away as possible from any air inlet
vents. Corrosive fumes may be released through
these vents when air is not being brought in
through them.

Chemicals that are corrosive in nature should not
be stored or used near the water heater or vent
termination.
Damage and repair due to corrosive compounds in the
air is not covered by warranty.
C199 Manual