1. Manuals
  2. Brands
  3. T&C Manuals
  4. Burner
  5. TC36.NG03.C.
  6. Instruction manual

T&C TC36.NG03.C. Instruction Manual

Black diamond burner kit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the fi replace and should be
kept together. Refer to the Installation and Operating Instructions
for proper gas supply, safety requirements and operating
instructions
010408-16
TC36
BLACK DIAMOND
BURNER KIT
INSTRUCTIONS
PART#
TC36.NG03.C.
FOR TC36
TC36.NG03.C
5056.427.C3

Advertisement

Table of Contents
loading

Related Manuals for T&C TC36.NG03.C.

Summary of Contents for T&C TC36.NG03.C.

  • Page 1 INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together. Refer to the Installation and Operating Instructions for proper gas supply, safety requirements and operating instructions TC36...

  • Page 2: Package Contents

    Package Contents • BURNER TUBE • MEDIA SPACER, Rear • BURNER TRAY ASSY • MEDIA SPACER, Front • 5 lbs. TUMBLED GLASS • MEDIA SPACER, Center • BURNER SHIELD • PANEL, LOWER REAR • MANIFOLD ASSEMBLY (including supply tube) • PILOT SHIELD (including pilot and supply tube) •...
  • Page 3 Fig. # 2 2) Attach the manifold bracket to the fl oor shield in the bottom of the fi rebox with one screw. (Fig. # 2) 3) Attach the manifold and pilot supply tubes to the bulk head Fig. # 3 fi tting and tighten.
  • Page 4 Fig. # 5 5) Remove panel retaining clips from the upper heat shield. Install right side panel by placing the bottom into the fi rebox and tipping the top into position. (Fig. # 5) 6) Position upper rear panel on top of lower rear panel and Fig.
  • Page 5 8) Install burner shield by tipping the shield into the fi rebox, Fig. # 8 feed the pilot assembly through the opening in the shield. (Fig. # 8) Fig. # 9 9) Attach pilot shield to burner tray with two screws. (Fig.
  • Page 6 11) Install front and rear media spacers. (Fig. # 11 & 12) Fig. # 11 Fig. # 12 12) Install burner by tilting burner inlet through tray. Ensure Fig. # 13 that the orifi ce has entered the inlet tube. (Fig.

  • Page 7: Inlet Tube

    Fig. # 14 ORIFICE INLET TUBE Fig. # 15 13) Install the center media spacer. Secure the spacer and burner with two long screws.(Fig. # 15) Four holes must line up to set each screw. Some pressure may need to be applied to the front tray support on the shield to align the holes.
  • Page 8 Fig. # 17 14) Apply just enough glass media to cover the burner assembly. (Fig # 17) NOTE: Too much glass media over the burner will cause sooting with the use of propane gas TC36.NG03.C 010408-16...

  • Page 9: Propane Conversion

    Propane Conversion If the unit is to be used on propane convert as follows using the components supplied with this fi replace: WARNING This conversion kit shall be installed Fig. # 18 by a qualifi ed service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction.
  • Page 10 6) Slide the pilot adjustment band over and ensure that the 9) Replace the minimum rate screw with the one provided in the propane conversion kit supplied with this fi replace. hole in the orifi ce band is showing. (Fig. #20 indicates NG position, Fig.

  • Page 11: Gas Pressure Test

    Fig. # 26 12) Fill in the date and the name of the person who performed the conversion in the white area on the conversion label. Peel off the protective backing and apply the conversion label directly over the gas specifi cations on the rating label. 13) Attach the access panel to the side of the fi rebox with the previously removed screws.

  • Page 12: Flame Adjustment

    Flame Adjustment The air shutter at the end of the burner inlet tube controls the primary combustion air to the gas burner and is preset closed at the factory for natural gas fuel. Shutter must be fully open for propane. See Fig. #29 for proper fl ame pattern. The fl ame should be just orange and “lazy”.

  • Page 13: Replacement Parts

    Replacement Parts NOTE: FIREPLACE & VALVE REPLACEMENT PARTS ARE LOCATED IN THE APPLIANCE INSTRUCTIONS ITEM..DESCRIPTION ........PART NO. ITEM ..DESCRIPTION ........PART NO. 10...BURNER SHIELD ........9636 1.... BURNER TUBE ......TC36.5011835 11...SPRING NUT ..........5044 2.... ORIFICE, NG ........... 5022.13 12...BURNER TRAY ...........
  • Page 14 NOTES TC36.NG03.C 010408-16...
  • Page 15 NOTES TC36.NG03.C 010408-16...
  • Page 16 TECHNICAL SUPPORT: 1-877-715-2664 www.townandcountryfi replaces.net 2975 Allenby Rd., Duncan, BC V9L 6V8 Printed in Canada...

Table of Contents